Klipsch WA-2 Bedienungsanleitung

Klipsch Subwoofer WA-2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Klipsch WA-2 (4 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

WA-2 WIRELESS SUBWOOFER KIT

Owner's Manual

IMPORTANT SAFETY INSTRUCTIONS!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wider blade or the third

prong are provided for your safety. If the provided plug does not ﬁt into your

outlet, consult an electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories speciﬁed by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table speciﬁed by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods

of time.

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

15. DO NOT ex pose this apparatus to dripping or splashing and ensure

that no objects ﬁlled with liquids, such as vases, are placed on the apparatus.

16. To completely disconnect this apparatus from the AC Mains, disconnect the power

supply cord plug from the AC receptacle.

17. The mains plug of the power supply cord shall remain readily operable.

The exclamation point, within an equilateral triangle, is intended to

alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

The lightning ﬂash with arrowhead symbol within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufﬁcient

magnitude to constitute a risk of electrical shock to persons.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to

rain or moisture.

WARNING: No naked ﬂame sources – such as candles – should be placed on the product.

Place the equipment near a main power supply outlet and make sure that you can

easily access the power breaker switch.

WARNING: This product is intended to be operated ONLY from the AC Voltages listed on

the back panel or included power supply of the product. Operation from other voltages

other than those indicated may cause irreversible damage to the product and void the

products warranty. The use of AC Plug Adapters is cautioned because it can allow the

product to be plugged into voltages in which the product was not designed to operate.

If the product is equipped with a detachable power cord, use only the type provided

with your product or by your local distributor and/or retailer. If you are unsure of the

correct operational voltage, please contact your local distributor and/or retailer.

FCC AND CANADA EMC COMPLIANCE INFORMATION

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not in-stalled and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved under the veriﬁcation provision of FCC Part 15 as a Class B Digital Device.

Caution: Changes or modiﬁcations not expressly approved by the manufacturer could

void the user’s authority to operate this device.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

EU COMPLIANCE INFORMATION

Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive

2006/95/EC; Conforms to European Union EMC Directive 2004/108/EC.

WEEE NOTICE

Note: This mark applies only to countries within the European Union (EU)

and Norway.

This appliance is labeled in accordance with European Directive 2002/96/EC

concerning waste electrical and electronic equipment (WEEE). This label indicates that

this product should not be disposed of with household waste. It should be deposited at

an appropriate facility to enable recovery and recycling.

WIRELESS TRANSMITTER COMPLIANCE INFORMATION

The term “IC:” before the radio certiﬁcation number only signiﬁes that Industry

Canada technical speciﬁcations were met. This equipment complies with FCC and IC

radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20cm between the radiator

and your body. This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

Le terme «IC:» avant le numéro de certiﬁcation radio signiﬁe seulement que les

spéciﬁcations techniques d’Industrie Canada ont été respectées.

Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites ﬁxées

pour un environnement non contrôlé. Cet appareil doit être installé et utilisé avec une

distance minimale de 20 cm entre le radiateur et votre corps. Cet transmetteur ne doit

pas être co-situé ou opérant en liaison avec toute autre antenne ou transmetteur.

This device has been designed to operate with the antennas listed below, and having a

maximum gain of [x] dB. Antennas not included in this list or having a gain greater than

[x] dB are strictly prohibited for use with this device. The required antenna impedance

is 50 ohms.

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not

more than that permitted for successful communication.

C A U T I O N

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this

equipment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel.

THANK YOU FOR YOUR PURCHASE OF THE KLIPSCH

WA-2 WIRELESS SUBWOOFER KIT!

The WA-2 will only operate with select Klipsch, Energy, Mirage and Jamo brand

subwoofers that have a “WA Port” input. The WA-2 is a 2.4 GHz product designed to

wirelessly transmit a signal up to a 50 foot radius.

Packing List:

1. Transmitter

2. Receiver

3. Power supply

4. Audio cable

5. Velcro strips

6. This Owner’s Manual

SETUP

1. Decide where the subwoofer will go (refer to your subwoofer owner’s manual).

2. Most receivers (and pre-ampliﬁers) have a line level subwoofer output labeled

Subwoofer Pre Out, Sub Out, SW Out, etc. If you have this, connect one end of

the supplied audio cable to it and connect the other end of the cable into WA-2

transmitter input ‘C’ . In absence of a subwoofer output connect Left and Right

channel Pre-Amp outputs from your receiver (if provided) to ‘C’ and ‘B’ inputs on

the transmitter.

3. Connect the cable from the WA-2 receiver to the “WA Port” on the back of the

subwoofer. Carefully match the 4 pins of the cable to the corresponding 4 holes

on the WA Port and gently push in until connected. Improper pin alignment can

result in damage to the connector.

4. Plug supplied power supply cable into ‘E’ on the WA-2 transmitter and plug other

end into an AC wall outlet.

5. Check to make sure Gain Switch ‘A’ is in middle position (0dB). This position best

matches the output voltage of most receivers and processors.

6. Turn receiver/pre-ampliﬁer on.

7. Turn subwoofer to “On” or “Auto On” position.

8. The WA-2 transmitter and receiver should be automatically “paired”with their

green LED’s ‘D’ on solid and the subwoofer should now be operational.

9. You can use the supplied Velcro strips to attach the WA-2 receiver to the back

of the subwoofer. Some subwoofers have two screws on back that the receiver

attachezs to.

TROUBLESHOOTING

- If the subwoofer does not operate and the red LED’s ‘D’ are ﬂashing on the WA-2

transmitter and receiver, a simple “pairing” is needed. Push and hold in button

‘F’ on the transmitter while pushing and holding button ‘G’ on the receiver and

keep pushed until both LED’s stop ﬂashing and glow solid (approximately 5

seconds).

- Since the WA-2 is a wireless device it may encounter RF interference from other

wireless devices in the same area. If there is difﬁculty “pairing” the transmitter

and receiver, or their signal connection “fades”, you may need to move them

closer together and/or farther away from other “wireless” products.

- If you do not get a signal, or get a low signal level from the subwoofer, make

sure the subwoofer out level control on your surround receiver is set correctly

(usually at the halfway point sometimes labeled “0dB”). If your subwoofer out

level on your surround receiver is correct, and you have adjusted the subwoofer

volume level and the signal is still too low, move the gain control ‘A’ to the right

(+12dB) to increase the signal to the subwoofer. If the signal is too high, move the

gain control to the left (-12dB) to reduce signal strength.

Produktspezifikationen

Marke:	Klipsch
Kategorie:	Subwoofer
Modell:	WA-2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Klipsch WA-2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Subwoofer Klipsch

Klipsch SW-310 Bedienungsanleitung

18 September 2024

Klipsch RSW SUB Bedienungsanleitung

16 September 2024

Klipsch Icon Series XW Sub Bedienungsanleitung

8 September 2024

Klipsch C Series C-310ASWi Bedienungsanleitung

8 September 2024

Klipsch SUB 260 Bedienungsanleitung

2 September 2024

Klipsch R-120SWi Bedienungsanleitung

25 August 2024

Klipsch LF-10 Bedienungsanleitung

14 August 2024

Klipsch KD-10SW Bedienungsanleitung

7 August 2024

Klipsch Reference Premiere RP-1600SW Bedienungsanleitung

3 August 2024

Klipsch Reference Premiere RP-1400SW Bedienungsanleitung

2 August 2024

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung für -Kategorien-

Pioneer S-21W Bedienungsanleitung

13 Oktober 2024

JL Audio SGR-10TW3 Bedienungsanleitung

13 Oktober 2024

Polk DB1040 Bedienungsanleitung

10 Oktober 2024

Blaupunkt GBW801 Bedienungsanleitung

7 Oktober 2024

JL Audio TW1 Bedienungsanleitung

6 Oktober 2024

Jensen J12W Bedienungsanleitung

6 Oktober 2024

Musway MT169Q Bedienungsanleitung

6 Oktober 2024

JL Audio 12W0v3 Bedienungsanleitung

4 Oktober 2024

Yamaha YST-SW315PN Bedienungsanleitung

2 Oktober 2024

JBL SW10 Bedienungsanleitung

30 September 2024