Klipsch CP-4 Bedienungsanleitung

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Klipsch CP-4 (60 Seiten) in der Kategorie Speaker. Dieser Bedienungsanleitung war fĆ¼r 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/60
CP SERIES
OWNERā€™S MANUAL
RECOMMENDED RECEIVER/AMPLIFIER POWER TO USE WITH KLIPSCH CP SPEAKERS
A speaker can be damaged just as easily with too little power as
with too much power. A general rule is when you raise the volume
level on a receiver/ampliļ¬er past the ā€œone halfā€ (or ā€œ12 oā€™clockā€
position with a marked volume knob), that receiver/ampliļ¬er is now
starting to work beyond its capabilities, sending harmful distortion
that can damage any speaker, no matter how many watts that
speaker is rated to accept. This is true for any speaker and receiver/
ampliļ¬er combination. The recommended wattage to use on your
new Klipsch CP speaker depends on which one you have you have:
CP-4: up to 50 watts continuous (for an extended period of time);
200 watt ā€œpeaksā€ (very short bursts/surges)
CP-6: up to 75 watts continuous (for an extended period of time);
300 watt ā€œpeaksā€ (very short bursts/surges)
HOOKING SPEAKERS UP TO AN AMPLIFIER/RECEIVER
When connecting speakers to an ampliļ¬er/receiver, always
make sure speaker polarity is correct and the best sound is
obtained by connecting amp/receiver positive (+) to speaker
positive (+) and amp/receiver negative (-) to speaker negative
(-). The CP speaker terminals are designed to accept up to 16
gauge wire.
One pair of Klipsch CP Series speakers, 8 Ohms, can connect to
the left/right speaker terminals of any 8 Ohm rated ampliļ¬er/
receiver as shown:
+
-+
-+
-
+
-
ONE PAIR TO
8 CAPABLEĪ©
AMP/RECEIVER
Right Channel Left Channel
IF YOU WISH TO USE TWO PAIRS OF KLIPSCH CP
SERIES SPEAKERS ON ONE AMPLIFIER/RECEIVER
WE RECOMMEND ONE OF TWO METHODS:
Method 1 (Preferred): IF your amp/receiver has both A
and B speaker terminals, connect one pair to A and one
to B. Depending on your amp/receiverā€™s capability you
can then either play Speaker pairs A and B together or
separately or Speaker pair A OR Speaker pair B only.
Method 2: IF YOUR AMP/RECEIVER IS RATED TO 4
OHMS OR LESS make a parallel wire connection as shown
from the amp/receiverā€™s right and left speaker terminals.
Your amp/receiver may output more power to the
speakers this way (check amp/receiver speciļ¬cations).
OTHER POSSIBLE SPEAKER CONNECTION OPTIONS:
Series Wiring of Two Pairs to one Amp/Receiver:
Instead
of a parallel connection using a series connection as
shown has the amp/receiver work at 16 Ohms but this cuts
the power going to each of the speakers usually in half.
If you are using a surround (7/9/11 channel) receiver
that receiver MIGHT allow connection of an additional
pair of speakers to unused surround channels for use in a
different listening area or may have a ā€œZone 2ā€ capability
to connect those speakers (check your receiver manual)
Using an outboard speaker switcher:
Several types of
available selector boxes allow hookup of multiple pairs
of speakers to one ampliļ¬er/receiver and allow switching
between them. Some models allow simultaneous play of two
pairs of speakers. (see your audio dealer for availability).
+
-
+
-+
-+
-+
-
+
-
Right Channels Left Channels
HOOKING SPEAKERS UP TO AN AMPLIFIER/RECEIVER (CONTINUED)
R
+
L
+
_
_
R
+
L
+
__
SPK A SPK B
Amp/Receiver Rear Amp/Receiver Front
SPK A SPK B
+
-
+
-+
-+
-+
-
+
-
Right Channels Left Channels
METHOD 2
METHOD 1
SERIES WIRING OF TWO PAIRS
TO ONE AMP/RECEIVER

Produktspezifikationen

Marke: Klipsch
Kategorie: Speaker
Modell: CP-4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Klipsch CP-4 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Speaker Klipsch

Bedienungsanleitung Speaker

Neueste Bedienungsanleitung fĆ¼r -Kategorien-