Kidde RF-SM-ACDC Bedienungsanleitung

Kidde Rauchmelder RF-SM-ACDC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Kidde RF-SM-ACDC (2 Seiten) in der Kategorie Rauchmelder. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
DO NOT POWER-UP THE DEVICES.
Locate the 8-position dipswitch on the back
of each of your Kidde Wireless devices.
Choose a random sequence of OFF and
ON positions and set all your devices to this pattern. The devices
only read the sequence when they are first powered up. DO NOT
USE THE DEFAULT CODE THE DEVICES WERE SHIPPED WITH!
Power each device up, push and hold the test button for 5 sec-
onds and verify all the devices produce an alarm signal. If all the
units do not respond, disconnect power, remove the batteries, verify
the dipswitches on all units are the same and wait 30 seconds.
Power the units back up and try again. If the units do not respond
refer to the user’s guide for more information
CAUTION: Due to the loudness of the alarm, always stand an
arms length away from the unit when testing.
Install your units using the guidelines in the User’s Guide and then
test again.
Test your Kidde wireless devices weekly to ensure changes in your
home, such as the location of furniture, have not interfered with
the reception and transmission capabilities of your system.
If your Wireless smoke alarms enter alarm mode, first check to
see if there is a fire. If a fire does not exist, and the test button
has not been activated on any of the units, it is likely that you
are receiving interference from a similar system nearby. In this
case, repeat the above steps and select a different dipswitch
pattern, making sure to disconnect the power and remove the
batteries before changing the switch positions.
Quick Setup Guide for
Kidde Wireless Alarms
1
2
3
4
5
DIPSWITCH
Battery Operated:
Alarm DOES NOT have any wires connected to the back of it.
The alarm is ONLY powered by a battery or batteries.
Hardwired:
Alarm has two wires (typically white and black colored) connected
to the back of it. Alarm DOES NOT have a third wire (typically red,
orange or yellow in color) connected to the back of it. You can
determine if an alarm is by confirming that two power Hardwired
wires are connected to it, and then by pressing the test button on
the alarm, and listening for the other alarms to sound. If other
alarms DO NOT sound, the alarm is Hardwired.
Hardwired with Interconnect:
Alarm has two wires (typically white and black colored) connected
to the back of it. Alarm DOES have a third wire (typically red,
orange or yellow in color) connected to the back of it. You can
determine if an alarm is by confirming Hardwired with Interconnect
that three wires are connected to it, and then by pressing the test
button on the alarm, and listening for the other alarms to sound.
If other alarms DO sound, the alarm is Hardwired with Interconnect.
DO NOT connect two RF-SM-ACDC alarms to a Hardwired with
Interconnect system. Doing so will result in the RF-SM-ACDC alarms
triggering each other. They will not stop alarming until one is
disconnected from the electrical circuit. If your home has Hardwired
alarms, which are not interconnected, you can use up to twelve
RF-SM-ACDC alarms.
TEST YOUR ALARMS WEEKLY: This ensures that changes in your
environment (i.e. moved furniture, addition of electronic appliances)
have not adversely affected the operation of your Wireless system.
820-0926 Rev.A
Types of Alarms


Produktspezifikationen

Marke: Kidde
Kategorie: Rauchmelder
Modell: RF-SM-ACDC

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kidde RF-SM-ACDC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Rauchmelder Kidde

Bedienungsanleitung Rauchmelder

Neueste Bedienungsanleitung für -Kategorien-