Kemppi A7 MIG Power Source 350 Bedienungsanleitung
Kemppi
Las apparaat
A7 MIG Power Source 350
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Kemppi A7 MIG Power Source 350 (67 Seiten) in der Kategorie Las apparaat. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/67
350, 450
1920300
1824
A7 MIG WelderA7 MIG Welder
EN
OPERATING MANUAL
2A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
2. Installation .............................................................................................5
3. System Overview ................................................................................6
3.1 Power Source ............................................................................................. 6
3.2 Robot interface unit ..................................................................................7
3.3 User interfaces ........................................................................................... 8
3.4 A7 MIG Wire Feeder 25 ..............................................................................9
3.5 MIG Guns .................................................................................................11
3.6 Cooling unit .............................................................................................12
3.7 I/O device.................................................................................................13
4. Using the welder ...............................................................................14
4.1 Basic controls ...........................................................................................14
4.2 Setup panel .............................................................................................14
4.2.1 Button functions ..................................................................................15
4.2.2 Main menu ..........................................................................................16
4.2.3 Memory channel wizard ........................................................................16
4.2.4 User settings ........................................................................................22
4.2.5 Welding system settings ........................................................................22
4.2.6 System tests ........................................................................................25
4.2.7 Robot settings .....................................................................................26
4.3 Web user interface ..................................................................................29
4.3.1 Welding display....................................................................................30
4.3.2 Gas, air and wire inch ............................................................................30
4.3.3 Logbook .............................................................................................31
4.3.4 About .................................................................................................31
4.3.5 Welding settings – Memory channels .......................................................31
4.3.6 Settings – Language .............................................................................35
4.3.7 Settings – Users ....................................................................................35
4.3.8 Settings – Change PIN ...........................................................................35
4.3.9 Settings – Fieldbus................................................................................36
4.3.10 Settings – Network ...............................................................................36
4.3.11 Settings – Backup, restore and reset .........................................................37
4.3.12 Settings – Licenses ................................................................................37
4.4 User identication ...................................................................................38
4.4.1 Overview ............................................................................................38
4.4.2 Turning user identication system on .......................................................39
4.4.3 Creating new users ...............................................................................39
4.4.4 Deleting a user .....................................................................................40
4.4.5 Changing user role ...............................................................................40
4.4.6 Changing username ..............................................................................40
4.4.7 Changing PIN code ...............................................................................40
4.4.8 Resetting PIN code ...............................................................................41
4.4.9 Logging in and out, changing active user ..................................................41
4.5 Touch sensor (seam search) ....................................................................42
4.5.1 Voltage source, levels and safety .............................................................44
4.5.2 Touch tool ...........................................................................................45
4.5.3 Fast status output .................................................................................45
4.5.4 Selecting output voltage .......................................................................45
4.5.5 Conguring touch tool ..........................................................................46
4.6 Through Arc Seam Tracking (TAST) ........................................................46
4.7 Collision sensor .......................................................................................47
4.7.1 Setting collision sensor on and o ...........................................................48
4.7.2 Selecting sensor type ............................................................................48
4.7.3 Selecting output polarity .......................................................................48
4.8 Wire feeder ..............................................................................................49
4.8.1 Loading the ller wire ...........................................................................49
4.9 Arc measurement ....................................................................................53
4.9.1 Setup and calibration ............................................................................53
4.9.2 Display ...............................................................................................53
3A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.10 Gas ow sensor .......................................................................................54
4.10.1 On/O control .....................................................................................54
4.10.2 Gas ow sensing level ...........................................................................54
4.10.3 Gas mixture setup ................................................................................55
5. Troubleshooting ................................................................................56
5.1 Typical problems .....................................................................................56
5.2 Error codes ...............................................................................................57
5.2.1 Power source errors ..............................................................................57
5.2.2 Cooling unit errors ................................................................................58
5.2.3 Wire feeder errors .................................................................................59
5.2.4 Welding curve errors .............................................................................59
5.2.5 Robot interface errors............................................................................60
5.2.6 I/O device errors ...................................................................................61
6. Operation disturbances ..................................................................62
7. Maintenance .......................................................................................63
7.1 Daily maintenance ..................................................................................63
7.2 Periodic maintenance .............................................................................63
7.3 Service shop maintenance ......................................................................63
8. Disposal ................................................................................................64
9. Ordering numbers ............................................................................64
10. Technical data ....................................................................................65
Produktspezifikationen
Marke: | Kemppi |
Kategorie: | Las apparaat |
Modell: | A7 MIG Power Source 350 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kemppi A7 MIG Power Source 350 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Las apparaat Kemppi
23 September 2024
22 September 2024
22 September 2024
22 September 2024
20 September 2024
20 September 2024
17 September 2024
24 August 2024
23 August 2024
22 August 2024
Bedienungsanleitung Las apparaat
- Las apparaat Parkside
- Las apparaat GYS
- Las apparaat Elektra Beckum
- Las apparaat DEKO
- Las apparaat Frilass
- Las apparaat Weldkar
Neueste Bedienungsanleitung fĂĽr -Kategorien-
17 September 2024
27 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024