JVC VN-V685U Bedienungsanleitung
JVC
Überwachungskamera
VN-V685U
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JVC VN-V685U (130 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 34 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/130
PTZ IP DOME CAMERA
OUTDOOR PTZ IP DOME CAMERA
VN-V685U
VN-V686BU
VN-V686WPBU
INSTRUCTIONS
Thank you for purchasing this product.
Before beginning to operate this unit, please read
the instruction manual carefully in order to make
sure that the best possible performance is
obtained.
For Customer Use:
Enter below the Serial No. which is located on the
body.
Retain this information for future reference.
Model No.
VN-V685U/VN-V686BU/VN-V686WPBU
Serial No. LST0819-001A
VN-V686WPBU
VN-V685U/
VN-V686BU
2
Getting Started
Safety Precautions
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK. DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE.REFER SER VICING T O
QUALIFIED SERVICE PERSONNEL.
The lightning flash wish arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the pres-
ence of uninsulated "dangerous volt-
age" within the product's enclosure that
may be of sufficient magnitude to con-
stitute a risk of electric shock to per-
sons.
The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important op-
erating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
FOR USA AND CANADA Information for USA
This device complies with part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product
should be handed over to the applicable collection point for the recycling of
electrical and electronic equipment for proper treatment, recovery and recycling
in accordance with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your local municipal office, your household waste disposal service
or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance
with national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with
applicable national legislation or other rules in your country for the treatment of
old electrical and electronic equipment.
Attention:
This symbol is
only valid in
the European
Union.
3
● This installation should be made by a
qualified service person and should conform
to all local codes.
● This installation shall be in accordance with
the National Electrical Code, ANSI/NFPA 70.
● The unit is to be powered by an AC 24 V
power supply.
The AC 24 V power supply should conform to
the following:Class 2 only(For USA),Isolated
power supply only(For Europe and other).
● Any Mention in this manual of Alarm inputs/
outputs have not been evaluated by UL to be
used for Burglar Alarm Functionality.
FOR USA-California Only
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material -
special handling may apply.
See
www.dtsc.ca.gov/hazardouswaste/perchlorate
4
Getting Started
These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances.
1. Read all of these instructions.
2. Save these instructions for later use.
3. All warnings on the product and in the operating instructions should be adhered to.
4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
5.
Do not use attachments not recommended by the appliance manufacturer as they may cause hazards.
6. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool, etc.
7.
Do not place this appliance on an unstable cart, stand, or table. The appliance may
fall, causing serious injury to a child or adult, and serious damage to the appliance.
Use only with a cart or stand recommended by the manufacturer, or sold with the
appliance. Wall or shelf mounting should follow the manufacturer’s instructions,
and should use a mounting kit approved by the manufacturer. An appliance and
cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the appliance and
cart combination to overturn.
8. Slots and openings in the cabinet and the back or bottom are provided for
ventilation, and to insure reliable operation of the appliance and to protect it from
overheating, these openings must not be blocked or covered. The openings
should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface.
This appliance should never be placed near or over a radiator or heat register. This appliance should
not be placed in a built-in installation such as a bookcase unless proper ventilation is provided.
9.
This appliance should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your dealer or local power
company. For appliance designed to operate from battery power, refer to the operating instructions.
10.For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and power-line surges.
11.Do not allow anything to rest on the power cord. Do not locate this appliance where the cord will be
abused by persons walking on it.
12.Follow all warnings and instructions marked on the appliance.
13.Do not overload wall outlets and extension cords as this can result in fire or electric shock.
14.Never push objects of any kind into this appliance through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the appliance.
15.Do not attempt to service this appliance yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
16.Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under
the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the appliance.
c. If the appliance has been exposed to rain or water.
d. If the appliance does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the appliance to normal operation.
e. If the appliance has been dropped or the cabinet has been damaged.
f. When the appliance exhibits a distinct change in performance - this indicates a need for service.
17.When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
18.Upon completion of any service or repairs to this appliance, ask the service technician to perform
routine safety checks to determine that the appliance is in safe operating condition.
IMPORTANT SAFEGUARDS
PORTABLE CART WARNING
(symbol provided by RETAC)
S3125A
5
Getting Started
Safety Precautions ........................................2
Contents ........................................................5
Main Features ...............................................6
Safety precautions .........................................8
Operating Environment .................................8
Precautions ...................................................9
Name and Function of Parts .......................13
VN-V685U/VN-V686BU ...........................13
VN-V686WPBU .......................................15
Features ......................................................16
Connection/Installation
(VN-V685U/VN-V686BU)
Mounting the Camera ..................................18
Power Connection .......................................23
LAN Cable Connection ................................24
Connecting the alarm signal terminal ..........25
Connection/Installation
(VN-V686WPBU)
Mounting the Camera ..................................26
Power Connection .......................................30
LAN Cable Connection ................................31
Connecting the alarm signal cable ..............32
Network Setting
Network Requirements ................................33
IP Address Settings .....................................36
IP address setting procedure ..................36
IP address setting at the computer ..........37
Internet Explorer settings ........................38
Connecting the camera to the computer
.....40
IP address setting for the camera ............42
Enter user name and password ...............44
Setting Using Internet Explorer
Setting ......................................................... 46
How to open the setting page ..................46
Basic Settings1 ....................................... 47
Basic Settings2 ....................................... 48
Camera Page ..........................................51
Encoding Page ........................................56
Alarm Page ..............................................58
Alarm Environment Page ........................62
PTZ Page ................................................66
Auto Patrol Page .....................................72
Privacy Mask Page .................................. 74
Motion Detection Page ............................76
Network Basic Page ................................78
Network Details Page ..............................80
Protocol Page ..........................................81
Streaming Page .......................................82
Access Restrictions Page ........................84
Time Page ...............................................86
Password Page ........................................87
Maintenance Page ..................................88
List of Factory Settings of Each Page .....90
Miscellaneous page .................................94
Operation Page .......................................95
Settings Page ..........................................96
Position List Page ....................................99
Patrol Settings Page ..............................100
Operation
Built-in Viewer ...........................................101
Screen Configuration of Built-in Viewer
....102
Image quality setting .............................104
PTZ Setting ...........................................106
PTZ Control ...........................................112
JPEG Viewer Settings ...........................117
MPEG4 Viewer Settings ........................119
Operator Password ................................121
Exiting the Viewer ..................................122
Others
Troubleshooting .........................................123
Specifications ............................................126
Contents
6
Getting Started
Support for PoE (Power over Ethernet)
This camera supports PoE (IEEE802.3af) and enables
power supply through a LAN cable.
T
Connect to AC 24 V when using the heater.
(VN-V686WPBU only)
Dual Stream Full Frame Rate
Transmission
Dual stream (JPEG, MPEG4) data transmission
is possible in VGA size at a rate of 30 fps.
Realizing a High Picture Quality
This product uses high resolution 380,000 pixels
CCD and a new digital image processing IC to
achieve high resolution and image quality.
Progressive Output
This function realizes high picture quality of
moving objects by fixing combing noise on the
contour of the objects.
Long Magnification Zoom Lens
The optical 36 times (VN-V686BU/VN-
V686WPBU) and 27 times (VN-V685U) long
magnification lenses allow you to conduct
detailed monitoring. The high power and large
focal ratio F1.6 (WIDE edge) and bright zoom
lens realize 1.0 lux (AGC Super, 50 %) high
sensitivity during color mode.
Equipped with high precision high
speed rotation platform
The newly developed direct drive rotation platform
rotates at a high speed of 400
⬚
/s both horizontally
and vertically, thus allowing the camera to move to
the preset positions quickly. As it does not have a
slowdown mechanism, it is very durable, has a high
stopping accuracy and can rotate smoothly even at
low speed.
Image Stabilizer
This function detects camera shaking and reduces
image shaking.
Automatic Tracking function
This product is equipped with a function that easily
tracks moving objects when home position is
displayed.
Intelligent Tracking Feature
This feature enables you to track color information of
the object that you selected by clicking. Linking the
zoom feature enables tracking while automatically
adjusting to the optimal magnification ratio.
Day/Night surveillance
This product is equipped with infrared filter
mechanism for day/night surveillance. During low
illuminance such as nighttime, switching out the
infrared filter will switch the product to high sensitivity
mode (B&W).
Privacy Mask function
This function allows you to blank out areas that you do
not wish to display in the location to be recorded.
Motion Detection Feature
This feature enables output of an alarm upon
detection of motion in the video image within preset
area. Pre-/Post-recorded JPEG image files can be
sent to FTP server by the alarm.
Support for Multicast
This product supports multicast, which enables
transmission of image data to multiple
computers on the network without lowering the
frame rate.
Support for IPv6 dual stack
This camera supports IPv6 and enables
transition from IPv4.
HTTP-based API
This product comes with HTTP-based API. This
feature enables you to perform setting and control via
the network.
Built-in Integrated Viewer Software
This product comes with a built-in integrated viewer
that enables you to monitor camera images (JPEG or
MPEG4) on the computer. It can also be used to
configure the camera settings and control the camera.
It also employs a new GUI for greater user-
friendliness.
Waterproof and Weatherproof Chassis
(VN-V686WPBU)
This camera is equipped with a dust-proof and drip-
proof mechanism that prevents it from being
subject to rain, and therefore can be installed
outdoors. (IP66 specification)
T However, VN-V685U/VN-V686BU can only
be used indoors. Do not use them in an
outdoor environment or expose them to
moisture.
Main Features
7
This manual contains the detailed
instructions for using this unit.
Please refer to [READ ME FIRST] for
description on the general usage of this
unit.
For the latest information, please refer to
the AReadmeB file in the CD-ROM supplied
with this product.
●
The supplied CD-ROM includes
INSTRUCTIONS (this manual) (pdf), [API
Guide] (pdf), [VSIP Guide] (pdf) and [Search
tool].
● Before starting an important recording, be
sure to perform a test recording in order to
confirm that a normal recording is possible.
●
We do not accept liability for the loss of a
recording in the case of it becoming
impossible to record due to a problem in the
video camera, VTR, hard disk recorder or
video tape.
●
The Automatic Tracking, Intelligent Tracking,
and Motion Detection features are simple
functions and cannot be used as a substitute
for a security alarm. JVC shall not be liable for
any inconveniences or damages caused in
the event of false detection or when these
functions cannot be detected. We shall not be
liable for any inconveniences or damages
caused as a result of operational failure for
alarm input/output.
How to Read this Manual
䡵
Symbols used in this manual
Note
:States precautions to be taken
during operation.
Memo
:States restrictions on the functions
or use of this equipment. For
reference purposes.
A
:Indicates the page numbers or items
to refer to.
䡵
Contents of this manual
●
JVC holds the copyright to this manual. Any
part or all of this manual may not be
reproduced without prior consent from the
company.
●
Windows is a registered trademark of
Microsoft Corporation in the U.S.
●
Product names of other companies described
in this manual are trademarks or registered
trademarks of the respective companies.
Symbols such as
姠
,
姞
and
姝
are omitted in
this manual.
●
Design, specifications and other contents
described in this manual are subject to
change for improvements without prior notice.
●
Screen displays in this manual may differ
from the actual ones.
8
Getting Started
Recommended Computer
Specifications
OS : Windows XP (Professional or
Home Edition) (SP2)
:Windows Vista Business (SP1)
CPU : Pentium4 2 GHz or higher
Memory capacity: 1 GB and above
Free hard disk space
:512 MB or more
Display and video card
:1024 ⳯ 768 pixels or higher, True
Color (24 bits or 32 bits)
VRAM 8 MB or more (256 MB
and above recommended)
Web browser: Internet Explorer
XP : Version 6.0
Vista : Version 7.0
LAN Environment
● 10BASE-T/100BASE-TX network
interconnected using devices such as an
IEEE802.3-compliant switching hub.
● IEEE802.3af-compliant switching hub when
PoE is used
●
IGMPv2-compliant network when multicast is
in use.
M
emo:
● The above PC specifications are guides for
smooth use of the applications, and not a
guarantee of their operation.
● Depending on the condition of use,
applications may not run smoothly even when
the user’s computer meets the specification
requirements.
● The following may occur if the performance of
the computer is insufficient.
● Playback frame rate for JPEG images may
drop
● Delay in the MPEG4 playback images
may occur, and playback is interrupted
● To use MPEG4 images on the integrated
viewer, install the open source codec
“ffdshow”. You can download “ffdshow” from
the Internet.
Safety precautions
Mounting to a firm place
As the unit rotates at high speed, mount it on a
firm place with sufficient strength to support
the vibration and weight of the unit
Mass:Approx. 1.9 kg
(VN-V685U/VN-V686BU)
:Approx. 5.5 k
g
(VN-V686WPBU)
If the strength is weak, the vibration will cause
fuzzy images on the monitor screen. In the
worst scenario, the camera may even fall off
and hit somebody, resulting in serious
accidents.
Mounting the camera correctly with
the designated clamping brackets
Always use the designated clamping brackets.
Be sure to connect the fall prevention wire and
tighten the fixing screws or nuts securely.
Using the correct power and voltage
The rated power of this product is AC 24 V, 50
Hz/60 Hz. Supplying a power beyond the rated
value may result in failures and in the worst
scenario, smoking and fire.
This unit is able to divert lightning conduction
to itself and the connecting cables to a certain
extent but this is not 100 % guaranteed. For
installation locations that are likely to suffer
lightning strikes, be sure to take appropriate
measures such as adding arrestor to the
connecting cables.
Consult your dealer as special technique is
required when installing this product. Ensure
that the fixing screws or nuts are tightened
securely, otherwise, the unit may fall off.
Inspect the unit regularly.
Screws may be loosened due to vibration or
deterioration of the mounting section. Perform
regular inspections for loosened screws and
check whether there is any danger of the unit
falling off.
Do not hang on this product, shake it, or hang
objects over it. Applying an excessive load
may cause the product to fall off and result in
accidents.
Do not modify this product. It may result in
accidents.
Operating Environment
9
Storage and operating environment
䢇
VN-V685U/VN-V686BU is an indoor camera. It
cannot be used outdoors.
䢇
VN-V685U/VN-V686BU is a pendant mount camera.
Be sure to place the camera head horizontally. The
product will not work properly if it is tilted.
䢇
VN-V686WPBU is specially designed to be mounted
on walls. Be sure to place the camera head
horizontally. The product will not work properly if it is
tilted.
䢇
Do not store in the following environments.
It might result in malfunctions or failure.
●
Locations beyond the allowable operating
humidity range of 20 %RH to 90 %RH.
(condensation is not allowed)
●
Near equipment that emits strong magnetic fields,
such as transformers or motors.
●
Near equipment that emits radio waves, such as
transceivers and mobile phones.
●
Locations with excessive dust and sand.
●
Locations that are subject to vibration such as
inside the car or ship.
●
Locations prone to moisture such as window side.
●
Locations subject to steam or oil, such as
kitchens.
●
Special environment, such as those with
combustible atmosphere
●
Locations that are subjected to radiation, X-rays,
salt attack or corrosive gases.
●
Locations where medicine is used such as pools.
●
Hot or cold places that are beyond the allowable
operating temperature range
䡵Allowable operating temperature
●
When power is supplied to VN-V686WPBU using
PoE, the heater will not work. Use an AC 24 V
power supply when using the camera in an
environment under -10
I
.
䢇
When using VN-V686WPBU in a low temperature
environment (-40
I
to -20
I
), images may not be
displayed for up to two hours until the interior is
warmed up by the built-in heater. It is therefore
recommended that power be supplied to the camera
at all times when the surrounding temperature is low.
Inadequate heat ventilation may result in malfunction
of this product. Be sure not to block vents around the
product. This product discharges heat from the
surface of the main unit.
䢇
Do not install it at locations directly subjected to cold
air such as near the vents of air-conditioners or at
locations with high temperature. Condensation may
occur inside the dome cover.
䢇
Use of this product and cables connected to this
product at locations where strong electric waves and
magnetic waves are generated (e.g., near radio, TV,
transformer, monitor, etc.) may cause noise
interferences in the images or changes in the color.
Others
䢇
Do not subject the lens to strong light source such as
sun rays. This may cause the equipment to
malfunction.
䢇
This camera comes with a built-in AGC circuit. The
sensitivity increases automatically at a dark place
and the screen may appear grainy. This is not a
malfunction.
䢇
While AGC is activated, if a transceiver which causes
strong electromagnetic wave is used near the
camera, the picture may suffer from beat. Please use
the camera more than three meters away from such
transceivers.
䢇
When automatic iris is selected, the Iris Control
button may not work depending on the brightness of
the screen (when the amount of light is not sufficient).
In this case, set the iris to Manual.
䢇
When automatic iris is selected and AGC is ON, even
if the iris setting can be changed with the Iris Control
button, the Sense Up function will be enabled and the
brightness of the screen may not change. In this
case, set AGC to OFF or set the iris to Manual.
䢇
When this camera is used in the White Balance
A
ATW-N ar ro w
B
,
A
ATW-Wi de
B
(automatic adjustment)
mode, the color tone may differ slightly from the
actual color due to the principle of the automatic
tracking white balance circuit. This is not a
malfunction.
䢇
If a high brightness object (such as a lamp) is shot,
the image on the screen may have white vertical
tailings. This phenomenon (smear) is characteristic of
solid-state image sensors and is not a malfunction.
䢇
Do not touch the dome cover with your hands. Dirty
covers will cause image deterioration.
䢇
Do not subject the dome cover to strong impact. It
may result in damage and water seepage.
䢇
The dome cover may fog up due to the drastic change
of temperature when humidity is high.
䢇
Do not connect an AC 24 V cable to AC 110 V/AC
230 V power supply. The camera internal circuit will
be damaged. Should that happens, do not use the
camera. Bring it to your nearest JVC dealer for repair.
(charged separately)
䢇
To supply AC 24 V, use an AC 24 V supplying power
unit that is insulated from AC 110 V/AC 230 V line.
Precautions
VN-V685U/VN-V686BU -10
I
to 50
I
VN-V686WPBU
AC 24 V power supply -40
I
to 50
I
PoE power supply -10
I
to 50
I
10
Getting Started
Others (continued)
䢇
Depending on the stop position and rotation speed of
the horizontal/vertical rotation platform, the running
sound of the rotation platformfs motor may be heard,
but this is not a malfunction.
䢇
When using multicast, make use of a IGMPv2-
compliant network switch.
䢇
Some hubs/switches of products that are equipped
with intelligent features may include a broadcast/
multicast suppression function. Viewing of
multicast images on this product may fail if this
function is enabled.
䢇
The electronic shutter of this product is set to 1/60
by default. For regions with a commercial power
supply frequency of 50 Hz, switch to the 1/100
during use under fluorescent lights (excluding
inverter lighting equipment) to prevent flickers.
䢇
When the B&W mode is set to
A
Auto
B
, the image
turns black-and-white in a dark location. As the
sensitivity level is increased in this case, the
screen may appear grainy and more white spots
may appear. When switching between color and
black-and-white images, the brighter area on the
screen is emphasized, which may reduce the
visibility. However, this is not a malfunction.
䢇
If the power supply voltage is momentarily cut off
or reduced due to lightning or turning on of the air
conditioner’s power, the image may be disrupted
or noise interference may occur.
䢇
As the dome cover is of a semiglobular shape,
image distortion will occur at the hemispherical
edge. When the hemispherical edge of this unit is
masked and horizontal level is shot in a tilt
direction, the hemispherical edge will enter the
field angle. This may cause the upper edge of the
screen to become black and the focus unclear. In
this case, you can avoid shooting the above area
by using the tilt limit settings (
A
Page 70).
䢇
When shooting objects with a luminance
difference or near a light source, ghost may occur
on the screen. This is a feature of the dome cover
and the built-in lens, and is not a malfunction.
䢇
In particular, manual and auto pan operation near
the TELE edge (telephoto side) may cause the
screen to vibrate (unsmooth rotation). This is a
feature of the motor and is not a malfunction.
䢇
As long magnification lens is used in this product,
the focus may be unclear due to temperature
changes but this is not a malfunction.
䢇
Preset the focus under an environment with a
temperature closest to that in your actual usage. If
the temperature change is large and the focus
becomes unclear, preset the focus again before
using the product.
䢇
If you sense that the focus has become unclear
due to temperature changes, use the Auto
Foucua(AF) function or reset the focus
manually.
Transporting the unit
䢇
Remove the connecting cables when transporting
the unit.
䢇
When transporting the unit, turn off the power of
the system.
䢇
Pack the unit with cushioning material so as to
avoid shock when transporting.
䢇
Handle the unit with care and do not subject it to
vibration or shock.
Copyright Protection
䢇
With the exception of the user being the
copyright holder or when permission such as for
duplication has been granted by the copyright
holder, permission is required in principle for the
duplication, modification, or transmission of
copyrighted video and audio data.
Unauthorized duplication, modification, or
transmission of copyrighted material may
constitute a copyright infringement, and the
user may be liable to compensate for any
damages. When using copyrighted video/audio
data, be sure to check the license agreement of
the copyrighted material thoroughly.
When rights or rights holders are involved with
regard to the targeted duplicating subject,
permission may be required for shooting or
using (processing) it. Be sure to check the
licensing conditions thoroughly.
Maintenance
䢇
Turn off the power before performing maintenance.
䢇
Wipe using a soft cloth.
Wiping with thinner or benzene may melt or tarnish
its surface. For tough stains, wipe using a cloth
that is dipped into a neutral detergent diluted with
water, followed by wiping with a dry cloth.
䢇
When the same position is monitored for 24 hours
continuously over a long period, the increased
contact resistance on the horizontal rotation
section may cause noise interferences in the
images and operation from the computer may
become unstable. As such, this product is
equipped with an auto cleaning function that
performs cleaning once a week.
Saving Energy
䢇
If the camera is not to be used for a long time,
turn off the power of the system for safety and
energy conservation reasons.
Precautions (continued)
11
Disclaimer
䢇
The Automatic Tracking, Intelligent Tracking, and
Motion Detection features are not features to
prevent theft or fire. Our company shall not be
liable for any inconveniences or failures that occur.
䢇
We shall not be responsible for any
inconveniences or disturbances caused in the
event of privacy invasion as a result of camera
footages of this product.
Transportation
䢇 Do not throw away the original box of the unit.
Keep it and use it for transporting the unit in
future.
䢇 As the camera unit is of an easily rotatable
structure, secure the camera unit inside the
dome cover such that it does not rotate
before transporting. Otherwise, an error may
occur during camera operation.
AFace the heat release vents upward and
secure the lens section with tape.
BInsert cushioning material wrapped with air
caps (approx. 50 mm x 200 mm) at two
opposite sides of the camera.
䢇 When attaching the ceiling clamping bracket
to the camera unit before transporting, pull
out the tip of the fall prevention wire to
prevent it from being caught between the
camera and clamping bracket. Otherwise, it
may be difficult to detach the bracket from the
camera. (VN-V685U/VN-V686BU)
A
B
A
B
Cushioning material
Secure
with tape
Pull out the tip of the fall
prevention wire
䡵VN-V685U/VN-V686BU
䡵VN-V686WPBU Cushioning material
Secure
with tape
12
Getting Started
Precautions (continued)
䡵
Consumable parts
The following are consumable parts. They must be
replaced once they reach their lifetime.
The lifetime is only an estimation and differs according
to the usage environment and conditions.
Replacement of consumable parts is chargeable within
the guarantee period.
●
Zoom lens assembly
Zoom operation ..... Approx. 2 million operations
Focus operation..... Approx. 4 million operations
●
Slip ring ................. Approx. 5 million operations
●
Cooling fan ...................... Approx. 50,000 hours
●
Heater relay(VN-V686WPBU)......... Approx. 100,000
times
●
Heater fan(VN-V686WPBU) ........... Approx. 50,000
hours
䡵
Auto Focus
This unit is equipped with Auto Focus functions.
However, depending on the object and the camera
setting, it might be out of focus. In this case, please
adjust the focus manually.
●
Objects which are difficult to be focused
automatically
●
When the brightness of the image plane is
extremely high (bright)
●
When the brightness of the image plane is
extremely low (dim)
●
When the brightness of the image plane is
constantly changing (for example, a blinking light)
●
When there is almost no contrast
●
When there are repetitive vertical striped patterns
on the image plane
●
Auto Focus is difficult to set under the following
conditions
●
When sensitivity is increased with AGC and the
screen is grainy
●
When there is less movement on the screen due
to the Sense Up function.
●
When there is no clear contour in electronic zoom
䡵
Zoom Operation
The following phenomena are the results of the built-in
lens performance and are not malfunctions.
●
When manual operation or preset is selected,
focus moves slightly after the zoom operation has
stopped near the TELE edge.
●
Manual zoom operation is not smooth.
●
When Preset is selected, the camera becomes out
of focus for an instant during zooming.
䡵
Preset Positions
The total number of preset positions that can be set in
this unit is 100, including the home position and 99
preset positions.
13
VN-V685U/VN-V686BU
䡵 Ceiling mount section
A
Fixing holes (x3)
This hole is for mounting the ceiling clamping bracket to
the ceiling or the ceiling recessed bracket (WB-S685:
Sold separately).
B
[AC24V
H
H
H
HH
INPUT] AC 24 V Input terminal
This connects the camera to AC 24 V power.
C
[10BASE-T/100BASE-TX] LAN cable connection
terminal
This connects the unit to the network.
It supports PoE (IEEE802.3af) and enables you to use
this camera without having to connect to a power supply
using a power cord.
PoE: class0 (
A
Page 24)
D
Alarm input/Alarm output terminal
This terminal is for alarm input/alarm output.
(
A
Page 25)
E
Fall prevention wire fixing bracket
This attaches to the fall prevention wire
J
of the camera.
F
Wire clamp fixing hole
This is used to bundle wires. (
A
Page 19)
G
Fall prevention wire mounting hole
Mount wires from the ceiling slab or channel to this hole
to prevent the camera from falling.
H
Power indicator
The indicator lights up in green when AC 24 V power/
PoE power is turned on.
I
[Mac address] indication
The MAC address is a unique physical address of the
product. This address cannot be altered.
J
Camera connection terminal (female)
This connects to the connection terminal (male) of the
camera.
Name and Function of Parts
B
D
C
F
E
G
A
H
T
erminal
J
I
Reverse side
Pin number Signal Name
1 Input 1
2 Input 1 COM
3 Input 2
4 Input 2 COM
5 Output 1
6 Output 1 COM
7 Output 2
8 Output 2 COM
14
Getting Started
VN-V685U/VN-V686BU (continued)
䡵 Camera
KFall Prevention Wire
This is fixed to the fall prevention wire fixing
bracket E of the ceiling clamping bracket.
L Camera lock knob (x2)
This mounts the camera on the ceiling and
secures it so that it does not fall.
M Front Mask
N Lens
Lens cannot be replaced.
O Cable cover
To pull the cables from the side and mount the
camera, remove the cover. (A Page 20)
P Dome Cover
The dome cover is a delicate object. Handle it
with care.
Note:
Do not peel off the protective sheet which is
attached at shipment, until the dome cover is
mounted on the main unit. ( A Page 21)
Name and Function of Parts
(continued)
L
K
N
M
O
L
P
15
VN-V686WPBU
ACamera securing hole (4 locations)
This hole is used for mounting the camera on the
wall.
B Cable connecting hole, cap
Remove the cap and pull out the cables from this
hole for connection.
( A Page 27)
C Fall Prevention Wire
Connects the camera to the wall. Secure the
camera tightly to the anchor bolts used to mount
the fall prevention wire on the wall. ( A Page 28)
D AC 24 V Power Cable
This connects the camera to AC 24 V power. (A
Page 30)
E Alarm Input/Alarm Output Cable (x8)
This cable is for alarm input and alarm output.
( A Page 25)
F LAN Cable
This connects the unit to the network.
( A Page 24)
G Dome Cover
The dome cover is a delicate object. Handle it
with care.
Note:
● It is covered with a protective sheet during
shipment. Do not remove this sheet until
installation is complete.
H Dome Cover Fixing Screws (x4)
I Heater ON/OFF Switch
This is the automatic control ON/OFF switch of
the built-in heater.
The built-in heater prevents the dome cover from
fogging up and snow or frost from attaching to
the dome cover. When installing the heater at an
unrequired location, turn off the switch of the
heater. It is usually set to ON. (A Page 26)
J Lens
Lens cannot be replaced.
K Front Mask
L [MAC address] indication
The MAC address is a unique physical address
of the product. This address cannot be altered.
A
H
B
C
D
E
G
A
F
䡵 Front side
L
K
J
I
䡵 Inner structure of
the camera
Cable color Signal Name
Brown Input 1
Red Input 1 COM
Orange Input 2
Yellow Input 2 COM
Green Output 1
Blue Output 1 COM
Purple Output 2
Gray Output 2 COM
16
Getting Started
Surveillance Using Built-in Viewer
This unit comes with a built-in ActiveX JPEG
Viewer and MPEG4 Viewer.
JPEG images and MPEG4 images of the
camera can be monitored using the computer by
installing this Built-in Viewer on the computer.
JPEG images that are currently displayed can
also be captured into the computer’s hard disk.
ABuilt-in ViewerB (APage101)
This unit accepts requests from a maximum of
20 clients.
Monitoring via Multicast
Multicast enables monitoring of JPEG and
MPEG4 images on multiple computers.
AStreaming PageB (APage82)
A BJPEG Viewer Settings (APage118)
AMPEG4 Viewer SettingsB (APage120)
Surveillance via Dual Stream
Simultaneous distribution of JPEG and MPEG4
images enables real-time surveillance using
MPEG4 (30 fps) and recording of JPEG images
at the same time. You can also lengthen the
recording time by lowering the frame rate,
resolution, and picture quality settings for JPEG
images.
Saving JPEG images to the FTP server
at regular intervals
JPEG images may be uploaded to the FTP
server at regular intervals.
A BFTP (APage63)
Features
Computer
camera
Network
Computer
Computer
Computer
IGMP-
Compliant
Network
camera
Computer
Real-time Surveillance
Using MPEG4
Network
Storage Device
Recording JPEG
camera
Computer
Uploads the latest
JPEG images to the
FTP server at regular
Network
camera
17
Alarm
This unit comes with a motion detection feature
and dual alarm input.
During motion detection or alarm input, actions
such as mail delivery, message transmission via
TCP/UDP, alarm output, moving to a preset
position, and changing of B&W mode settings
can be triggered. These actions can also be
triggered by combination of two alarm inputs.
Installing an FTP server enables uploading of
JPEG images before and after the alarm input
time (pre-/post-recording) to the server.
A BAlarm Page (APage58)
A BJPEG Viewer Settings (APage118)
Restrictions on Clients
This unit enables users to authorize or reject the
acquisition of images by specific IP address.
(
A
Page 84)
Control via customized application
software
The following uses are also possible by
developing a customized application software
that supports the API of this unit.
For details, please refer to [API GUIDE] in the
supplied CD-ROM.
● Monitors via the computer while at the same
time records images to the HDD of the
computer.
● Performs recording by changing the frame
size/frame rate during alarm occurrence.
● Records the type and time of alarm
occurrence on the computer.
Computer
Sending JPEG images
before and after alarm
input to FTP
Alarm Device
Network
camera
18
Connection/Installation (VN-V685U/VN-V686BU)
Preparation
1
Make holes on the ceiling
●
Use the provided template to make a hole (
R
80
mm) for the connection cables to thread behind
the ceiling.
●
If necessary, also open a screw hole to mount the
ceiling clamping bracket to the ceiling. In this case,
align the
A
D
FRONT mark
B
of the template in the
direction where the camera faces front and open
the screw hole.
2
Pull the cables from the hole in the ceiling
Pull out the fall prevention wire, power cable, coaxial
cable, control signal cable, alarm signal cable and
provided alarm cable that were mounted to the ceiling
slab from the ceiling.
Note:
●
Mount the fall prevention wire on a firm place with
sufficient strength.
3
Remove the ceiling clamping bracket from
the camera unit
The ceiling clamping bracket is attached to the
camera unit during packaging of the product. Before
installing the camera, remove the ceiling clamping
bracket from the camera unit.
A
Check to make sure that the two camera lock knobs
(left and right) are unlocked.
●
If they are locked, unlock by sliding them in the
direction indicated by the arrow.
B
Press the two camera lock knobs from both the left
and right sides in the direction indicated by the
arrows.
●
Doing so detaches the ceiling clamping bracket
from the camera. Prevent the bracket from
dropping such as by performing this on a table.
M
emo:
●
If the camera fixing lock knob is too stiff, push the
knob hard while pressing the edge of the camera
unit (
A
in the diagram) against the table you are
using.
C
Lifting the camera unit detaches the ceiling
clamping bracket. Remove by sliding it in the
direction indicated by the arrows.
4
Remove the terminal cover
Loosen two screws on the ceiling clamping bracket
and remove the terminal cover.
5
Mount the fall prevention wire that
connects the ceiling clamping bracket to
the ceiling
Mounting the Camera
Be sure to put on protective glasses to protect
your eyes from falling objects when mounting
the camera.
1
80
2
Alarm signal
cable
Power cable
LAN Cable
Fall
Preventio
C
B
B
A
A
Camera fixing
lock knob (x2)
Camera
Ceiling mount
Terminal cover
6 mm
䡵 Fall Prevention Wire
6 mm (3/16
R6 mm and
R4 to 5.5 mm
19
M
emo:
● The wire should be insulated from the ceiling
structure. If the ceiling structure is metal and
insulation is not provided between the
camera and the ceiling structure, image noise
may occur.
6 Connect the cable (A 23 25) to
Connect cables to the terminal of the ceiling
clamping bracket.
The connection cables consist of the alarm
signal cable, LAN cable and AC 24 V power
cable.
A LAN cable (A Page 24)
This connects the unit to the network.
B Power cable (A Page 23)
This connects to AC 24 V power.
C Alarm input/output signal terminal
(A Page 25)
This connects to devices with alarm input/output
terminals.
Note:
● Do not connect an AC 24 V cable to AC 110
V power supply. The camera internal circuit
will be damaged. Should that happens, do
not use the camera. Bring it to your nearest
JVC dealer for repair. (charged separately)
● For safety reasons, turn on the power only
after all the connection is complete.
● To supply AC 24 V, use an AC 24 V supplying
power unit that is insulated from AC 100 V
line.
7 Handling cables
Thread the provided wire clamp through the wire
clamp fixing hole of the ceiling clamping bracket
to tie all the wires.
Note:
● To prevent the cables from tangling and
coming off, be sure to thread a wire clamp
through the wire clamp fixing hole to tie the
cables.
Caution
●
Take note of the length, strength, pull and
material (insulation) of the fall prevention wire
and use one with a wire strength of more than
20k
g
.
●
The inner diameter of the ring section of the
fall prevention wire mounted on the camera
should be
R
4 mm to
R
5.5 mm and the outer
diameter be
R
9 mm and below.
●
The thickness of the screw head and the fall
prevention wire (including the washer) should
be 6 mm and below. If it is more than 6 mm,
the screw will touch the ceiling and the
camera cannot be installed horizontally.
●
Use M4 fixing screws.
A
B
C
Alarm signal cable
Power cable
LAN Cable
Tie here
Wire clamp fixing
hole
Wire clamp
20
Connection/Installation (VN-V685U/VN-V686BU)
Preparation (continued)
8
Mount the terminal cover
Return the terminal cover that was removed in step
3
to
its original position. The direction to pull out the cables
changes according to the mounting method of the
camera.
Note:
●
Be sure to mount the terminal cover to prevent foreign
objects or dust from entering.
●
When pulling out the cables from the top, make the
fall prevention wire go under the terminal cover and
pull it out together with the other cables.
●
When pulling out the cables from the side, remove the
cable cover of the camera.
Mounting the ceiling clamping bracket
to the ceiling
1
Secure the ceiling clamping bracket to the
ceiling
●
Install such that the
A
D
FRONT mark
B
of the ceiling
clamping bracket faces the front.
●
Ensure that the connection cables are not caught in
between and secure the ceiling clamping bracket to
the ceiling with 3 screws.
Note:
●
Use M4 fixing screws and bolts.
●
Use
R
4.1 wood screws.
●
The length of the screws should be 25 mm (1inch)
and above.
●
Place the product horizontally and install. The camera
will not operate properly if it is slanted.
●
The screw head should be 5 mm and below. If the
ceiling structure is metal, image noise may occur.
●
Do not use screws for which the screw head is
embedded after fastening. (e.g. flat countersunk head
screws). Otherwise, the insulating resin part may be
damaged, thus preventing proper insulation.
M
emo:
●
Always use 3 screws and mount securely.
●
Tighten the screws again during maintenance just to
be safe.
●
The plastic parts on the ceiling fixing holes of the
ceiling clamping bracket act as an insulation between
the ceiling clamping bracket and the ceiling structure.
If the ceiling structure is metal and insulation is not
provided between the camera and the ceiling
structure, image noise may occur. Be sure to provide
insulation.
Mounting the Camera
(continued)
䡵 Pulling out the cables from the top
Terminal cover
Fall Prevention Wire
(To go under the terminal co
v
䡵 Pulling out the cables from the side
Te r mi na l
cover
Cable cover
Screws
DFRONT mark
Front of the camera
5 mm (3/16
inch) and below
21
Mounting the camera to the ceiling
1 Remove the tape on the lens section
2 Remove the lens cap
3 Mount the dome cover to the camera
A Check that the dome cover and lens are
free from dirt.
B
Turn the dome cover in a clockwise direction
to mount.
Note:
● Be sure to turn the dome cover until it stops
and tighten securely. Make sure that the
dome cover is not slanted.
● Do not over-rotate the dome cover. This may
damage the dome cover.
M
emo:
● If it is difficult to screw on the dome cover,
turn it in an anticlockwise direction until you
hear a click sound, then turn it in a clockwise
direction. It will screw on smoothly.
4 Remove the dome cover protective
sheet
2
1
Camera
Ta pe
Lens cap
Caution
● The dome cover is an optical part. Handle
with care.
● When mounting the dome cover, make sure
that there is no dirt inside the cover.
● Tighten the dome cover securely.
3
4
Dome Cover
Dome cover
protective
sheet
22
Connection/Installation (VN-V685U/VN-V686BU)
5 Mount the fall prevention wire
Mount the fall prevention wire, which is attached
to the camera, to the fall prevention wire fixing
bracket of the ceiling clamping bracket.
6 Mount the camera
● Align the A BD mark (blue)/(red) inside the
camera with the A BD mark (blue)/(red) on the
ceiling clamping bracket.
● Insert the camera into the ceiling clamping
bracket until you hear a click sound and
mount it securely.
7 Check that the camera fixing lock
knobs (x2) are sticking out.
If the camera is mounted on securely, the
camera fixing lock knobs (x2) will stick out a little.
Note:
● Before mounting the camera, check that the
camera fixing lock knobs are not locked (i.e.,
lock knobs are on top). The camera cannot
be mounted if the lock knobs are locked.
● When pulling out the cables from the side,
remove the cable cover of the camera. (A
Page 18)
8 Lock
When the camera is mounted on the ceiling
clamping bracket, lower the camera fixing lock
knobs (x2) in the direction of the arrow and
secure the camera such that it does not fall off.
9 Remove the safety precautions sheet
on the camera
Read through details stated on the safety
precautions sheet again.
Removing the camera
A Release the lock by sliding the camera fixing
lock knobs toward the ceiling.
B Press the two camera fixing lock knobs from
both the left and right sides to remove the
camera unit.
C Remove the fall prevention wire by performing
the mounting procedures in the reverse
sequence.
Mounting the Camera
(continued)
Caution
● Be sure to connect the fall prevention wire.
Otherwise, the camera may fall.
● To prevent danger, do not leave the fall
prevention wire dangling by the camera.
6
5
7
D mark
(blue)
Fall prevention
wire fixing bracket
Fall Prevention Wire
D mark (red)
During
mounting
After
mounting
Caution
● Be sure to check that the camera fixing lock
knobs (x2) are locked securely. Otherwise,
the camera may fall.
● After mounting, check that the camera is
mounted securely. Improper mounting may
cause the camera to fall off.
9
8
Camera
fixing lock
knob (x2)
Sheet
23
Power can be supplied to this camera either by
connecting to an AC 24 V power supply or using
PoE (A Page .24)
Note:
● If power is supplied from both power cable
and LAN cable, priority will be given to the
power supply from the power cable.
● Be sure to use an AC 24 V supply that is
isolated from the primary power supply
circuit. Using a variable voltage power supply
will cause the camera and system to
malfunction or breakdown.
● The unit is to be powered by an AC 24 V
power supply. The AC 24 V power supply
should conform to the following: Class 2 only
(For USA), Isolated power supply only (For
Europe and others).
Connecting to an AC 24 V power supply
This connects the camera to AC 24 V power.
When using 2-core VVF (Vinyl-insulated vinyl-
sheath cable), the connection distance is as
follows: (Reference value)
M
emo:
●
After DHCP timeout, all IP addresses of camera are
set to 192.168.0.2 by default.
If the power of multiple cameras within the same LAN
environment are turned on at the same time, the IP
addresses of the cameras overlap, thus preventing
proper access. As such, make sure to turn on the
power of the cameras one by one.
●
In a system where multiple units of camera are used,
turn on the power of only one unit to configure the IP
address settings using the Internet Explorer. Upon
doing so, turn on the power of the second unit and
configure accordingly. Configure the subsequent
camera settings using the same procedure.
●
When there is an overlap of IP address, access to the
camera may fail. When this occurs, turn on the power
of only one camera unit within the same LAN
environment and wait for a while (at least 10 minutes).
Alternatively, turn off the power of all network devices
connected to the same LAN environment, followed by
turning them on again.
Note:
●
If thin cables are used, the resistance of the cables will
be high and a significant voltage drop will occur when
the camera is at its maximum power consumption
(when pan, tilt and zoom operates at the same time).
Either use a thick cable with low resistance or place
the power supply near to the camera and shorten the
length of the cable to restrict the voltage drop at the
rated current of the camera to below 10 %. If voltage
drops during operation, the camera may experience
unstable performance and be unable to call up the
preset position correctly.
●
Do not connect an AC 24 V cable to AC 110 V/AC 230
V power supply. The camera internal circuit will be
damaged. Should that happens, do not use the
camera. Bring it to your nearest JVC dealer for repair.
(charged separately)
●
Turn on the power only after the connection for all the
devices is complete.
●
After the power is turned on and activation is
completed, this product will move to the home
position. The default home position settings for pan,
tilt, and zoom are 1.00 °, 45 °, and p23-x1 respectively.
Power Connection
Maximum
connectio
n distance
50 m 150 m 230 m 390 m
Conductor
Diameter
(mm)
R1.0
and
above
R1.6
and
above
R
2.0
and
above
R
2.6
and
above
To Power Supply
Power cable
Warning
● The rated power of this product is AC 24 V, 50
Hz/60 Hz. Make sure to use it with the correct
voltage.
● Supplying a power beyond the rated value
may result in failures, smoke or fire. If the
camera breaks down, turn off the power and
contact our service center immediately.
● When a power beyond the rated value is
supplied, the internal components may be
damaged even if no abnormality is found on
the appearance and operation of the camera.
Please contact your nearest JVC dealer
immediately for servicing (charged
separately).
24
Connection/Installation (VN-V685U/VN-V686BU)
Using PoE
Supply power to the camera by connecting it to a
device that supports PoE via a LAN cable.
Connect the camera to a hub or computer using
a LAN cable.
䢇 When connecting to a hub
Make use of a straight cable.
䢇 When connecting to a computer
Make use of a cross cable.
Note:
● However, cross cables cannot be used with
some computer models. When connecting
this unit directly to a computer, check the
computer’s LAN specifications in advance.
Power Connection
(continued)
What is PoE (Power over Ethernet)?
PoE is a feature that transfers data and
supplies power simultaneously through a LAN
cable. It enables you to operate a LAN-
compatible equipment without having to
connect it to a power supply using a power
cord.
Cable to use
●
Shield (STP) cable
●
Length of 100 m or shorter
●
Make use of a Category 5 (or higher) cable .
[10BASE-T/100BASE-TX]
LAN cable connection
terminal
LAN Cable Connection
Cable to use
●
Shield (STP) cable
●
Length of 100 m or shorter
●
Make use of a Category 5 (or higher) cable .
[10BASE-T/100BASE-TX]
LAN cable connection
terminal
25
Connect the alarm signal cable to external
devices, such as a sensor or buzzer.
A Loosen screws on both sides of the
terminal block with a flathead screwdriver
and remove the terminal block as shown
in the diagram below.
M
emo:
● Inserting the tip of the screwdriver into the slit
of the terminal block will remove the terminal
block easily.
B Peel off about 4 mm of the alarm signal
cable covering and insert into the
terminal.
C Turn the screws at the side and secure the
alarm signal cable.
D When the alarm signal cable is secured,
return the terminal block that was
removed in A to its original position.
Note:
● Noises from an external source may cause
the camera to malfunction even when the
cable used is within 50 m. In this case, move
the cable away from the noise source.
Alarm input signal
Connects to sensors such as infrared sensors,
door sensors, metal sensors and manual
switches.
● To prevent noise from entering the internal
circuit, supply non-voltage contact signal to
the alarm input signal.
● Do not supply voltage.
● When the contact is short (MAKE) or open
(BREAK) on the menu, you can set it to
Alarm.
● Supply such that the alarm signal continues
for at least more than 500 ms. The alarm
signal may not be recognized if it is less than
500 ms.
Alarm output signal
Connect to alarm devices such as alarm,
indicator, light or buzzer.
●
Alarm output signal is an open collector output
insulated with photo coupler.
●
During an alarm, it is ON.
●
As this terminal is polarized, be sure to
connect it such that the voltage of the + output
is higher than that of the – output.
●
It will be damaged if reverse voltage is
supplied.
Connecting the alarm signal
terminal
Cable to use
● Length of 50 m or shorter
● UL1007, UL1015 or equivalent products
● AWG#22 to AWG#18 or equivalent
products
4 mm
A
B
C
A
D
Alarm signal
terminal
IN
COM
OUTPUT
COM
22
Rating:
Max. applied voltage: DC 20 V
Max. driving current: 25 mA
26
Connection/Installation (VN-V686WPBU)
Setting Up the Wall
1 Make holes in the wall
Make holes (R 45 mm) for the connecting cables
to pass through.
Note:
● Check the strength of the wall. A less firm
wall may cause the unit to fall.
2 Install the anchor bolts for mounting
the camera
Install 4 anchor bolts (M8 35 mm and above) ⳯
to mount the camera.
3 Install the anchor bolt for mounting
the fall prevention wire
Install the anchor bolt (M8 ⳯ 35 mm and above)
to mount the fall prevention wire 30 mm below
the center of the upper two anchor bolts that are
used to mount the camera.
4 Pull the cables from the hole in the
wall
Pull the power cable, LAN cable and alarm
signal cable from the wall.
Setting Up the Camera
1 Remove the dome cover
Loosen the screws (x4) and remove the dome
cover from the camera.
2 Remove the cushioning material, lens
cap and tape used during
transporting
When installing the heater at an unrequired
location, turn off the switch of the heater.
Mounting the Camera
Be sure to put on protective glasses to protect
your eyes from falling objects when mounting
the camera.
213
176
60
20
152
126
63
45
12
30
1
2
3
Anchor bolts to
mount the camera
Anchor bolt to
mount the fall
prevention wire
Alarm signal cable
Power cable
LAN Cable
Dome Cover
OFF
Cushioning material
Lens cap
Ta pe
Heater power
switch
27
3 Insert silica gel (when using PoE
power supply)
Note:
● Be sure to insert the provided silica gel in the
position as shown in the diagram when using
the PoE power supply.Otherwise, the camera
lens may fog up or the image may become
blur.
ARemove the screw and lift up the plate
B Take out 3 silica gels from the aluminum bag
and insert them into the position as shown in
the diagram.
C Fasten the screw
M
emo:
● During reconnection or re-installation after
repair or maintenance, make sure to replace
the silica gel with a new one.
● Consult your nearby JVCfs dealer on the
replacement procedures.Serial number of
part to be replaced: Use a LW40500-001A
silica gel.
Note:
● When mounting is performed on a rainy
day,make sure that rain water does not enter
this unit.
4 Mount the dome cover to the camera
Use the screws (x4) to mount the dome cover to
the camera. As a guide, install the three catches
of the dome cover and the central mark. Install
such that the central mark appears above the
JVC mark of the camera.
Note:
●
Check that there is no dirt or dust inside the dome
cover before mounting.
●
When installing on a rainy day, ensure that
raindrops do not enter the interior.
●
When mounting the dome cover, temporarily
secure the 4 screws and then tighten.
●
As a guide, tighten the screws to 0.5 N•m to 1 N•m
(5 kgf•cm to 10 kgf•cm). If the tightening is loose,
the dome cover may fog due to water seepage.
5
Remove the cable connection cap
Remove the cap on the arm of the camera.
6
Pull out the cables from the cable
connection hole
Pull out the cables (except the fall prevention wire) of
the camera from the cable connection hole.
C
B
A
Plate
Silica gel ⳯3
Position aligning catches (x3)
Face front
(towards direction of
the JVC mark)
4
5
Cable connection cap
28
Connection/Installation (VN-V686WPBU)
Mounting the Camera
1
Mount the fall prevention wire
●
Mount the fall prevention wire of the camera to the fall
prevention wire anchor bolt that was installed earlier.
●
Secure the fall prevention wire tightly with a nut and
washer.
2
Pull out the cables (from the wall) from the
cable connection hole.
3
Mount the camera to the wall
●
Mount the camera to the camera anchor bolts that
were installed earlier.
●
Secure the camera tightly with a nut and washer.
Note:
●
This product weighs approximately 5.5k
g
. When
installing, pay extra attention as it may fall.
●
For your safety, hold the arm section during
installation.
●
After installing, paint the nuts and washers to prevent
corrosion.
M
emo:
●
To remove the camera, follow the reverse procedures.
Cable Connection
1 Connecting the power cable
(A Page 30)
Connect the power cable and wind the
waterproof tape (adhesive).
After connecting, push the cable into the arm of
the camera.
2 LAN Cable Connection ( A Page 31)
A Use the provided RJ-45 conversion connector
and connect the LAN cable.
B Wind the connector section with waterproof
tape (adhesive) and push the cable into the
arm of the camera.
Mounting the Camera
(continued)
1
2
3
Fall Prevention
Wire
Washer
Nut
Wind the waterproof tape (adhesive)
Arm
B
A
Wind the
waterproof tape
(adhesive)
Arm
RJ-45
conversion
connector
(provided)
29
3 Connecting the alarm cable ( A
Page 25)
Connect the alarm cable and wind the
waterproof tape (adhesive).
After connecting, push the cable into the arm of
the camera.
Note:
● For cables that are not used, be sure to wrap
the ends individually with insulating tape.
● For safety reasons, turn on the power only
after all the connection is complete.
4 Mount the cap
5 Seal the cable connection hole and
around the mounting surface of the
camera with waterproof seal (GE
silicon).
Note:
● Ensure that waterproof treatment is
performed. Otherwise, the camera may
malfunction due to rain water seepage.
● Use GE silicon or other similar product for the
sealing material.
6 Remove the dome cover protective
sheet
Wind the waterproof tape
(adhesive)
Arm
4
5
Waterproof
treatment
Cap
Protective
sheet
30
Connection/Installation (VN-V686WPBU)
Power can be supplied to this camera either by
connecting to an AC 24 V power supply or using
PoE (A Page .31)
Note:
● If power is supplied from both power cable
and LAN cable, priority will be given to the
power supply from the power cable.
● Be sure to use an AC 24 V supply that is
isolated from the primary power supply
circuit. Using a variable voltage power supply
will cause the camera and system to
malfunction or breakdown.
● The unit is to be powered by an AC 24 V
power supply. The AC 24 V power supply
should conform to the following: Class 2 only
(For USA), Isolated power supply only (For
Europe and others).
Connecting the power cable
This connects the camera to AC 24 V power.
When using 2-core VVF (Vinyl-insulated vinyl-
sheath cable), the connection distance is as
follows: (Reference value)
M
emo:
●
After DHCP timeout, all IP addresses of camera are
set to 192.168.0.2 by default.
If the power of multiple cameras within the same LAN
environment are turned on at the same time, the IP
addresses of the cameras overlap, thus preventing
proper access. As such, make sure to turn on the
power of the cameras one by one.
●
In a system where multiple units of camera are used,
turn on the power of only one unit to configure the IP
address settings using the Internet Explorer. Upon
doing so, turn on the power of the second unit and
configure accordingly. Configure the subsequent
camera settings using the same procedure.
●
When overlapping of the IP address occurs, check to
ensure that there is only one camera unit within the
same LAN environment, and wait for a while (at least
10 minutes) or power off and on all network devices
under the same LAN environment. Otherwise, access
to the camera may fail.
Note:
●
If thin cables are used, the resistance of the cables will
be high and a significant voltage drop will occur when
the camera is at its maximum power consumption
(when pan, tilt and zoom operates at the same time).
Either use a thick cable with low resistance or place the
power supply near to the camera and shorten the
length of the cable to restrict the voltage drop at the
rated current of the camera to below 10 %. If voltage
drops during operation, the camera may experience
unstable performance and be unable to call up the
preset position correctly.
●
Do not connect an AC 24 V cable to AC 110 V/AC 230
V power supply. The camera internal circuit will be
damaged.
●
Should that happens, do not use the camera. Bring it to
your nearest JVC dealer for repair.
●
Turn on the power only after the connection for all the
devices is complete.
●
After the power is turned on and activation is
completed, this product will move to the home position.
Power Connection
Maximum
connectio
n distance
30 m 80 m 120 m 210 m
Conductor
Diameter
(mm)
R1.0
and
above
R1.6
and
above
R
2.0
and
above
R
2.6
and
above
To Power
Solder welding or
crimping
Insulating
tape
Warning
● The rated power of this product is AC 24 V,
50 Hz/60 Hz. Make sure to use it with the
correct voltage.
● Supplying a power beyond the rated value
may result in failures, smoke or fire. If the
camera breaks down, turn off the power
and contact our service center
immediately.
● When a power beyond the rated value is
supplied, the internal components may be
damaged even if no abnormality is found
on the appearance and operation of the
camera. Please contact your nearest JVC
dealer immediately for servicing (charged
separately).
31
Using PoE
Supply power to the camera by connecting it to a
device that supports PoE via a LAN cable.
Note:
●
When power is supplied to VN-V686WPBU using
PoE, the heater will not work. Use an AC 24 V
power supply when using the camera in an
environment under -10
I
.
Connect the camera to a hub or computer using
a LAN cable.
䢇 When connecting to a hub
Make use of a straight cable.
䢇 When connecting to a computer
Make use of a cross cable.
Note:
● However, cross cables cannot be used with
some computer models. When connecting
the camera directly to a computer, check the
computer’s LAN specifications in advance.
What is PoE (Power over Ethernet)?
PoE is a feature that transfers data and
supplies power simultaneously through a LAN
cable. It enables you to operate a LAN-
compatible equipment without having to
connect it to a power supply using a power
cord.
Cable to use
●
Shield (STP) cable
●
Length of 100 m or shorter
●
Make use of a Category 5 (or higher) cable .
RJ-45
conversion
connector
(provided)
LAN Cable Connection
Cable to use
●
Shield (STP) cable
●
Length of 100 m or shorter
●
Make use of a Category 5 (or higher) cable .
RJ-45
conversion
connector
(provided)
32
Connection/Installation (VN-V686WPBU)
Connect the alarm signal cable to external
devices, such as a sensor or buzzer.
Note:
● Noises from an external source may cause
the camera to malfunction even when the
cable used is within 50 m. In this case, move
the cable away from the noise source.
Alarm input signal
Connects to sensors such as infrared sensors,
door sensors, metal sensors and manual
switches.
● To prevent noise from entering the internal
circuit, supply non-voltage contact signal to
the alarm input signal.
● Do not supply voltage.
● When the contact is short (MAKE) or open
(BREAK) on the menu, you can set it to
Alarm.
● Supply such that the alarm signal continues
for at least more than 500 ms. The alarm
signal may not be recognized if it is less than
500 ms.
Alarm output signal
Connect to alarm devices such as alarm,
indicator, light or buzzer.
●
Alarm output signal is an open collector output
insulated with photo coupler.
●
During an alarm, it is ON.
●
As this terminal is polarized, be sure to
connect it such that the voltage of the + output
is higher than that of the – output.
●
It will be damaged if reverse voltage is
supplied.
Connecting the alarm signal
cable
Cable to use
● Length of 50 m or shorter
● UL1007, UL1015 or equivalent products
● AWG#22 to AWG#18 or equivalent
products
Solder welding or
crimping
Insulating
tape
IN
COM
Rating:
Max. applied voltage: DC 20 V
Max. driving current: 25 mA
OUTPUT
COM
22
33
Network Setting
● Ensure that there is sufficient network
bandwidth for the data volume to be sent out
by the camera. Do not send multicast stream
that exceeds the bandwidth. If the entire
bandwidth is used by the multicast stream,
control of this camera via the network may fail.
● Data volume to be sent by the camera varies
with the settings and number of distributions.
● The maximum bit rate for transmission is about
20 Mbps.
Estimation of Total Bit Rate
The total JPEG bit rate from the camera is
determined by the camera settings, number of
clients, and the client’s requested number of
frames. The total MPEG4 bit rate from the camera
is determined by the number of distributions.
Develop a design upon taking the above into
consideration.
Bit Rate of JPEG Stream
The JPEG file size per frame varies with the
encoding settings as well as input video signals.
The following table may be used as a reference.
䡵 AFS (Average File Size)
When AFS is selected, encoding will be
performed such that the target file size is the
average size of multiple JPEG images.
䡵 VFS(Variable File Size)
When VFS is selected, the quantization table
during JPEG encoding will be maintained,
and the file size will increase/decrease
according to the input signals.
The maximum number of distributions varies with
the bit rate settings as well as the client’s
requested frame rate. Up to 20 streams can be
distributed (including multicast). The total frame
rate refers to the sum of these frame rates.
For example, when 10 fps is requested by two
clients, and in addition, multicast is transmitted at
a rate of 10 fps, the total frame rate will be:
10 +10 +10 = 30 fps
If the JPEG file size per frame is 30 KB, then the
total bit rate will be:
30 KB × 30 fps = 900 KB/s = Approx. 7.2
Mbps
Network Requirements
Selectable between 10 KB
to 100 KB
Selectable between 3 KB
to 33 KB
VGA QVGA
1 (High) 80 KB 27 KB
2 60 KB 20 KB
3 40 KB 13 KB
4
(Medium) 30 KB 10 KB
5 25 KB 8 KB
6 20 KB 7 KB
7 (Low) 15 KB 5 KB
34
Network Setting
Bit Rate of MPEG4 Stream
You can select either the Variable Bit Rate (VBR) or
Constant Bit Rate (CBR) system for MPEG4 stream.
When the VBR system is selected, the bit rate varies
according to the condition of the input video signals. The
VBR system delivers a stable picture quality, but forecast
of the bit rate is difficult.
When the CBR system is selected, encoding is performed
at a fixed bit rate regardless of the condition of the input
video signals. The picture quality varies under the CBR
system, but the bit rate can be easily forecast.
You can specify an estimated bit rate for both VBR and
CBR. (64 kbps to 8000 kbps)
Restrictions on the Number of Distributions for
Camera
The maximum number of distributions for this unit is
determined by the settings as well as requirements from
the client.
When only JPEG images are distributed, the maximum
number of distributions is determined based on the
highest bit rate within the stream. When a distribution
request that exceeds the maximum number of
distributions is received, this request is denied. For
example, if Client A requests for and receives data at 1
Mbps, while Client B requests for and receives data at 5
Mbps, the maximum number of distributions is 4 streams
according to the table below.
Maximum number of distributions when only JPEG
data is distributed
When only MPEG4 images are distributed, the maximum
number of distributions is determined by the preset bit rate.
When a distribution request that exceeds the maximum
number of distributions is received, this request is denied.
When distributing only MPEG4 data
When both JPEG and MPEG4 images are
distributed simultaneously, distribution up to two
clients for JPEG and MPEG4 respectively is
possible. However, distribution requests that
exceed a total bit rate of 20 Mbps will be denied.
Insufficient network bandwidth
When there is insufficient bandwidth, the number of
JPEG frames (frame rate) that the client can acquire will
decrease. Delay will also occur in the distribution of
images. In the case of MPEG4, noise interference may
occur and playback may fail.
Network Requirements
(continued)
Distribution at
maximum bit
rate
Maxi
mum
numb
er of
distrib
utions
Total maximum
bit rate
1 Mbps and
below
20 20 Mbps
5 Mbps and
below
4 20 Mbps
10 Mbps and
below
2 20 Mbps
Larger than 10
Mbps
1 Maximum
configurable value
(24 Mbps)
Preset bit rate
Maxi
mum
numb
er of
distrib
utions
Total maximum
bit rate
0.6 Mbps and
below
20 12 Mbps
3 Mbps and
below
4 12 Mbps
6 Mbps and
below
2 12 Mbps
Larger than 6
Mbps
1 Maximum
configurable value
(8 Mbps)
Total bit rate
Maximum
number of
distributions
for JPEG
Maximum
number of
distributions
for MPEG4
20 Mbps and
below
2 2
35
Network Delay
When the client acquires JPEG via TCP, the
camera will send out data while checking the
ACK from the client at the same time. For
networks with considerable delay, data cannot
be sent out until ACK is received, and therefore
the frame rate will drop. In the case of MPEG4,
noise interference may occur and playback may
fail.
Decrease in the frame rate due to network
delays can be eliminated by receiving data via
multicast.
Network Jitter
When there is considerable network jitter, delay
time may be prolonged and the image frame rate
may drop. In the case of MPEG4, noise
interference may occur and playback may fail.
Packet Loss
When acquiring images from this unit via TCP,
packet loss may be recovered by TCP
retransmission. When there is considerable
delay in the network, however, missing data may
occur and the image frame rate may drop. In the
case of MPEG4, noise interference may occur
and playback may fail.
When packet loss occurs during multicast
sending from this unit, the image frame rate may
drop. In the case of MPEG4, noise interference
may occur and playback may fail.
List of Protocols and Port Numbers
Used by this unit
This unit uses the protocols and port numbers
listed below. Ensure that these ports are allowed
through the firewall when a firewall is to be
installed.
Protocol/Port No. Purpose of Use
Source
TCP/80 JPEG/MPEG4 server,
Web Settings page, API
TCP/5510 VSIP
TCP/10020
TCP/10021
TCP/10023
(Reserved for
adjustment)
TCP/32040 Alarm Server
Destination
TCP/20, 21 FTP
TCP/25 Mail delivery
TCP/110 POP (Mail Delivery)
TCP/User Setting
No.
Sending alarm
UDP/123 SNTP
UDP/5510 VSIP
UDP/9541 VSIP discovery protocol
UDP/User Setting
No.
Sending alarm
36
Network SettingNetwork Setting
IP address setting procedure
Follow the procedure below to configure the IP
address of the camera.
Step1 IP address setting at the
computer
(APager37)
G
Step2 Internet Explorer settings
(APager38)
G
Step3 Connecting the camera to the
computer
(APager40)
G
Step4 IP address setting for the camera
(APager42)
䢇 System configuration required for setting
IP address
Camera at factory default is set to ADHCP
EnableB
(DHC
P client function is On). When it is
connected to a LAN without DHCP servers, it will
activate under the following IP address after
timeout.
IP address : 192.168.0.2
Subnet mask : 255.255.255.0
Default gateway
: None
M
emo:
● To set a static IP address for the camera,
connect the camera, the switching hub and
the computer for setting using a straight LAN
cable of Category 5 and above.
䢇 Set up the computer for setting the IP
address.
● Minimum computer specifications for
setting
OS : Windows XP (Professional or
Home Edition) (SP2)
Web browser
: Internet Explorer Version 6.0
Note:
● When setting the IP address of the camera,
do so by using a network that is made up of
only the camera, the computer for setting and
the switching hub.
● Using a hub connected to other network
devices or networks via a LAN cable for
setting can cause problems.
IP Address Settings
Set the IP address of the computer for
configuring the camera settings.
Configure the Internet Explorer settings in
order to establish connection between the
computer and the camera.
Connect the computer to the camera.
Set the [DHCP Disable] item on the [Basic
Settings1] screen to ADHCP EnableB or
A BDHCP Enable .
37
IP address setting at the computer
Set the computer to an IP address that enables communication with the camera.
1 Click [Start]
● Select in the sequence of [Control Panel]- -[Network Connection] [Local Area].
Windows Vista:
● Select in the sequence of [Settings]- [Control Panel]- [Network Center]- [Network Connection].
2 The computer on which Internet Explorer is launched automatically selects the
connected network
●
Right-click and select [Properties].
● Check to ensure that the [Client for Microsoft Networks] and [Internet Protocol(TCP/IP)] check
boxes are selected.
Windows Vista:
● Check to ensure that the [Client for Microsoft Networks] and [Internet Protocol Version 4 (TCP/
IPv4)] check boxes are selected.
3 Select [Internet Protocol(TCP/IP)] and click [Properties]
Windows Vista:
● Select [Internet Protocol Version 4 (TCP/IPv4)] and click [Properties].
4 Set the IP address
5 Click [OK] on the [Local Area Connection Propertise] screen
A
B
C
D
EClick [OK].
Specify the [IP address]. (For example, use
192.168.0.100 when the camera is in its
default settings and there is no DHCP
server.)
M
emo:
Make sure that you take note of the original IP
address before altering.
Note:
Ensure that a duplicate IP address is not specified
within the same network environment.
Set [Subnet mask] to a value that is
appropriate for the setting operation. Consult
the network administrator if you have any
queries.
(Use 255.255.255.0 the camera is in its
default settings and there is no DHCP
Select [Use the following IP address].
When a [Default gateway] is present, make
use of the corresponding IP address (e.g.,
192.168.0.254).
38
Network SettingNetwork Setting
Internet Explorer settings
1 Launch the Internet Explorer on the computer
2 When proxy settings are enabled in the Internet Explorer, follow the steps below to
disable the proxy of the Internet Explorer
● Select in the order of [Tool] [Internet Options]- - -[Connections] [LAN Setting], followed by
deselecting the check for [Use a proxy server for your LAN] under [Proxy Server] of the [Local
Area Network (LAN) Settings] window.
3
If the active script of the Internet Explorer is disabled, follow the steps below to enable it
● Select [Trusted sites] under [Tool]-[Internet Options]-[Security]. Upon doing so, the [Sites...]
button directly below becomes active. Click this button and deselect the check [in the displayed
window], and add the following web site to the zone.
http://192.168.0.2
● Next, select [Trusted sites] under [Tool]-[Internet Options]-[Security], and press the [Custom
Level] button. Select [Enable] under [Scripting]-[Active script] of the [Security Settings] window
that has been opened.
IP Address Settings
(continued)
Deselect the check
Select [Enable]
39
4 If ActiveX controls and plug-ins
of the
Internet Explorer is disabled, follow the steps
below to enable it
● Click [Trusted sites] under [Tool]-[Internet Options]-[Security]. Select the [Custom Level] button
and open the [Security Settings] window. Set all items under [ActiveX controls and plug-ins] in
the opened window to [Enable]. Enable also [Use the following IP address] under
[Miscellaneous].
5 Disable pop-up block
Connection of the camera cannot be established when pop-up block in the Internet Explorer is set to
A BEnable .
Follow the steps below to set the pop-up block to disableA B.
● Selecting [Tool]-[Pop-up Blocker]-[Turn Off Pop-up Blocker] permits all sites.
● To allow only specific sites such as this unit, select [Tool]-[Pop-up Blocker]-[Turn On Pop-up
Blocker], followed by selecting [Tool]-[Pop-up Blocker]-[Pop-up Blocker Settings] that becomes
active to open the [Pop-up Blocker Settings] window.
In the opened window, add the address of VN-V686BU as a permitted web site address.
6 If plug-in tools are installed in the Internet Explorer, disable the pop-up block
function of these plug-in tools as well.
Select [Enable]
40
Network SettingNetwork Setting
Connecting the camera to the computer
1 Launch the Internet Explorer
M
emo:
● If the proxy server settings for access to the Internet via the Internet Explorer is enabled, you may
not be able to specify the IP address directly. In this case, change the proxy settings of the Internet
Explorer.
● After the [Security Settings] screen appears, press the [OK] button to proceed.
2 Enter the user name and password (login as administrator) ( A Page 44)
M
emo:
● After the [Security Settings] screen appears, press the [Yes] button to proceed.
IP Address Settings
(continued)
A B
Click [Go].
Enter the following IP address into the address field.
http://192.168.0.2
䡵 When the IP address of the camera is unknown
IP address settings cannot be changed by accessing via a computer when the IP address of the camera is unknown.
You can use the following method to identify the IP address.
●
Search for the camera in the LAN using [Search tool] inside [Tool_E] folder of the supplied CD-ROM.
T
For details on [Search tool], please refer to the
A
Readme
B
file in the CD-ROM supplied with this product.
A
B
C
Enter the user name.
This is set to A Badmin by default.
Enter the password.
This is set to A Bjvc by default.
Click [OK].
41
3 Built-in Viewer appears
4 The Operator Password entry screen appears
A Operator Password (default password is A Bjvc )
B Click [OK].
M
emo:
● The operator password entry screen does not appear if the password is stored on the computer.
Proceed to configure the IP address. (A Page 42)
A
B
42
Network SettingNetwork Setting
IP address setting for the camera
1 Click [Advanced Settings] of the Built-in Viewer
2 The [Basic Settings1] screen appears
A Specify the [DHCP Disable].
● When selecting A BDHCP Enable :
The default setting is ADHCP EnableB (DHCP client function is Enabled). To assign an IP
address from the DHCP server, connect the DHCP server to the LAN, set the [DHCP Disable] of
the camera to , and click the [OK] button. For details on IP addresses assigned ADHCP EnableB
to the camera, consult your network administrator.
● When selecting A BDHCP Enable :
Select ADHCP EnableB, and specify a value in the [IP address], [Subnet Mask] and [Default
Gateway] fields.
Note:
● Set the DHCP server such that the same IP address is always assigned to the MAC address of the
camera by the DHCP server. Connection may fail if the above setting is not performed.
IP Address Settings
(continued)
Click
A
B
C
43
B Specify the [Time Zone].
C Click [OK].
3 A confirmation screen appears
Click [OK].
Camera restarts using the new IP address. It takes about one minute for the camera to reboot.
M
emo:
● Access from this computer may fail when the IP address of the camera is changed. To enable
access to this unit from the same computer, alter the IP address at the computer accordingly.
When the display or configuration of the opened screen appears strange, check the computer
settings using the following procedures.
AClick [Start]-[Control Panel]-[Display] and open the [Display Properties] window
B Click the [Settings] tab in the [Display Properties] window and click the [Advanced] button
C Check that [DPI setting] in the [General] tab has become [Normal size(96DPI)]
D Otherwise, change the setting to [Normal size(96DPI)] and reboot Windows
44
Network SettingNetwork Setting
Enter user name and password
User name and password entry will be required
at the beginning.(A Page 40)
There are three access authorization levels to
the camera. The factory settings are as follows.
䢇 Pages that users have access to
Restrictions are placed on the pages that users
have access to. In addition, links on the web
pages are also displayed according to the
access rights of the user.
● admin
● operator
IP Address Settings
(continued)
User
Name
Default
Password
Description
admin jvc All operations and
setting changes are
allowed
operator jvc Change of settings
other than those
related to network
and maintenance
are allowed
user jvc Viewing of images
is allowed
Basic Settings1 [Network]
[Time]
Basic Settings2 [Camera]
[Encoding]
[JPEG]
[MPEG4]
Detalis [Camera]
[Encoding]
[Alarm]
[Alarm Environment]
[PTZ]
[Auto Patrol0]
[Auto Patrol1]
[Auto Patrol2]
[Privacy Mask]
[Motion detection]
[Network Basic]
[Network Details]
[Protocol]
[Streaming]
[Access Restrictions]
[Time]
[Password]
[Maintenance]
[Miscellaneous]
[Operation]
[Settings]
[Position List]
[Patrol Infomation 0]
[Patrol Infomation 1]
[Patrol Infomation 2]
Basic Settings2 [Camera]
[Encoding]
[JPEG]
[MPEG4]
Detalis [Camera]
[Encoding]
[Alarm]
[Alarm Environment]
[PTZ]
[Auto Patrol0]
[Auto Patrol1]
[Auto Patrol2]
[Privacy Mask]
[Motion detection]
[Streaming]
[Miscellaneous]
[Operation]
[Settings]
[Position List]
[Patrol Infomation 0]
[Patrol Infomation 1]
[Patrol Infomation 2]
45
● user
M
emo:
● Security Information window may appear
before the top page is displayed. Press the
[OK] button to proceed.
If you do not want this warning screen to be
displayed, change the Internet Explorer
settings as follows.
● Open [Tool]-[Internet Options]-[Security]
and select the [Trusted sites] icon.
● Next, press the [Custom Level] button,
followed by selecting A BEnable for
[Miscellaneous]-[Display mixed content].
Note:
● Do not reset or turn off the power of camera
immediately after the settings are changed.
Otherwise, changes may not be saved or may
be saved incorrectly.
● If settings are changed when sending JPEG
or MPEG4, the transmission may be
temporarily cancelled.
Detalis [Miscellaneous]
46
Setting Using Internet Explorer
How to open the setting page
1 Enter the IP address of the camera in the address bar of Internet Explorer ( A
Page 40)
● A Built-in Viewer is opened.
2 Click [Detalis]
● [Basic Settings1] page will be opened if accessed by user name A Badmin . (A Page 47)
● [Basic Settings2] page will be opened if accessed by user name A Boperator . (A Page 48)
● [Miscellaneous] page will be opened if accessed by user name AuserB. (A Page 94)
Setting
Click
47
Basic Settings1
This page is for performing basic setting related to the network.
● This page can be used during access using A Badmin .
● Click [Basic Settings1].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
M
emo:
● You can open the [Basic Settings1] screen without going through Built-in Viewer by entering direct
URL address in the address field of Internet Explorer.
When the IP address of the camera is 192.168.0.2 for example, enter the URL below.
VN-V685U :http://192.168.0.2/cgi-bin/v685display.cgi?v685basicmenu1.html
VN-V686BU/VN-V686WPBU :http://192.168.0.2/cgi-bin/v686display.cgi?v686basicmenu1.html
A
B
C
D
E
F
G
Click
Network
AIP Setting For setting the DHCP client function. Connect the camera to a network
environment with a DHCP server when DHCP is to be enabled. If the DHCP
server does not exist when [IP Setting] is set to ADHCP EnableB, the camera
will start running with IP address 192.168.0.2 and subnet mask 255.255.255.0
in about 2 minutes after startup. (A Page 42)
BIP Address For setting the IP address of the camera.
C Subnet
Mask
For setting the Subnet Mask of the camera.
D Default
Gateway
For setting the Default Gateway of the camera.
Set as 0.0.0.0 when the Default Gateway is not set.
Time
ETime Displays the clock time of the camera.
The time transmitted by the camera is recorded in the JPEG header.
Discontinuity may occur in the JPEG header’s time immediately before and
after changing the time.
FTime Zone For setting the time zone.
G Pc time to
Camera
Click the [Set] button to set the time of the computer on the camera.
48
Setting Using Internet Explorer
Basic Settings2
Page for setting fundamental parameters of Camera, JPEG and MPEG4.
● This page can be used during access using A B A Badmin or operator .
● Click [Basic Settings2].
● Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
M
emo:
● You can open the [Basic Settings2] screen without going through Built-in Viewer by entering direct
URL address in the address field of Internet Explorer.
When the IP address of the camera is 192.168.0.2 for example, enter the URL below.
VN-V685U :http://192.168.0.2/cgi-bin/v685display.cgi?v685basicmenu2.html
VN-V686BU/VN-V686WPBU :http://192.168.0.2/cgi-bin/v686display.cgi?v686basicmenu2.html
A
B
C
D
E F G H I
Click
49
Camera
ACamera ID Character strings entered here will be written to the JPEG comment segment
(item name: Camera). Refer to the [API Guide] (provided CD-ROM) on the
file formats of JPEG.
B Monitor
Type
For selecting the monitor type according to the monitor used to display the
video images. The picture quality varies according to the type of monitor
selected.
Custom :Enables setting of picture quality according to the user’s
preference. You can configure the detailed settings on the
[Camera] page. ( Page 51)A
LCD1, LCD2 :Picture quality setting for LCD monitors. Two types are
available for selection according to the user’s preference.
CRT :Picture quality setting for CRT (cathode-ray tube) monitors.
[Setting value:Custom, LCD1, LCD2, CRT]
Encoding
CFrame Size For setting the frame size of each JPEG or MPEG4 screen to VGA (640 x
480) or QVGA (320 x 240).
Select one of the four different patterns.
M
emo:
● Refer to the API Guide on the file formats of JPEG.
JPEG
D Quality/
Size
For specifying the JPEG picture quality (rate control mode) and size (target
file size). When AVFS1B to AVFS7B is selected, the quantization table during
JPEG encoding will be maintained and the file size will increase/decrease
according to the input signals. Typical sizes will be displayed in the Size field.
When recording JPEG data to a recorder with a limited storage capacity, the
maximum recording time may vary as the file size fluctuates under this
setting.
When AAFSB
is selected, encoding is performed su
ch that the target file size
is the average size of multiple JPEG images. You can enter the target size in
the Size field.
[Picture quality values:VFS1 to VFS7, AFS]
M
emo:
The picture size can be specified only when the picture quality value is set to
AFS.
[Size field setting range for VGA:10 KB to 100 KB ]
[Size field setting range for QVGA:3 KB to 33 KB ]
50
Setting Using Internet Explorer
Basic Settings2 (continued)
Setting (continued)
MPEG4
EBitrate For setting the MPEG4 encoding bit rate.
[Setting range: 64 kbps to 8000 kbps]
F Bitrate
Control
For selecting whether to set the MPEG4 rate control mode to CBR (Constant
Bit Rate) or VBR (Variable Bit Rate).
CBR : Encoding is performed at a fixed bit rate regardless of the
condition of the input video signals. Enables easy forecast of
the bit rate.
VBR : Changes the bit rate according to the condition of the input
video signals. Picture quality is stable, but forecast of the bit rate
is difficult.
GFPS For setting the MPEG4 frame rate.
[Setting range: 1 fps, 7.5 fps, 10 fps, 15 fps, 25 fps, 30 fps]
H I Frame
Interval
For setting the I-frame interval. MPEG4 starts encoding from the I-frame.
Shortening the interval stabilizes the picture quality even when there are
rapid changes in the video image. However, the picture quality for images
with little change will deteriorate. In addition, when multicast packet loss
occurs, the time interval required to restore the image is shorter.
[Setting value:30, 60, 90, 120, 150]
IPriority For selecting whether to assign priority to the frame rate or picture quality
during MPEG4 encoding.
FPS : Assigns priority to frame rate. Select this setting to enable
smooth monitoring of motion images.
Quality : Prioritizes image quality.
51
Camera Page
This page is for setting the camera’s parameters.
This page can be used during access using A Badmin or
A Boperator .
● Click [Advanced Settings] to display setting menu.
● Click [Camera]. Press the [OK] button to enable the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
● To restore the settings of this page to the factory settings, press [Initialize] button.
A
B
C
D
E
F
G
H
I
J
K
L
M
Click
ACamera ID Character strings entered here will be written to the JPEG comment segment
(item name: ACameraB). Refer to the [API Guide] (provided CD-ROM) on the
file formats of JPEG.
B
Monitor Type
For selecting the monitor type according to the monitor used to display the
video images. The picture quality varies according to the type of monitor
selected.
Custom : Enables setting of picture quality according to the user’s
preference.
LCD1, LCD2 : Picture quality setting for LCD monitors. Two types are
available for selection according to the user’s preference.
CRT : Picture quality setting for CRT (cathode-ray tube) monitors.
[Setting value:Custom, LCD1, LCD2, CRT]
CBlack Level For adjusting the black level. Lowering the value darkens the video image.
Increasing the value brightens the image.
[Setting range:0 to 2]
M
emo:
● If the black level is set to , this may be too low depending on the A B0
connected device, or dark area will become complete black.
● When using MPEG4 images, set to either A B A B1 or 2 .
52
Setting Using Internet Explorer
Camera Page (continued)
Setting (continued)
DGamma To alter the appearance of dark areas in a video image, adjust the gamma
curve.
0 : Gamma correction suitable for CRT is performed.
1 : Gamma correction suitable for some LCDs is performed.
2 : Do not perform gamma correction. This setting is suitable for
some LCDs.
Active : The most appropriate gamma correction is applied according to
the darkness of the screen. Select the level under [Active
Gamma Level].
[Setting value:0, 1, 2, Active]
M
emo:
● The set value is fixed when the [Monitor Type] is set to BA BLCD1 ,
A B ALCD2 , or CRTB.
Active Gamma
Level This adjusts the effect when [Gamma] D is set to A BActive .
Objects with little luminance differenceBDecrease the number
Objects with large luminance differenceBIncrease the number
[Setting range:-5 to 0 to 5]
M
emo:
● The color may appear different from the actual one depending on the
object.
● Noise interference and hue changes may appear prominent depending
on the brightness of the object but this is not a malfunction.
● This feature can only be configured when [Gamma] D is set to A BActive .
E Enhance
Frequency
For setting the type of edge enhancement.
Low : Enhanced edges become thicker.
High : Enhanced edges become thiner.
[Setting value:Low, High]
M
emo:
● The set value is fixed when the [Monitor Type] is set to BA BLCD1 ,
A B ALCD2 , or CRTB.
FEnhance Level For setting the intensity of edge enhancement.
Larger value : Increases the intensity of edge enhancement.
Smaller value : Decreases the intensity of edge enhancement.
[Setting range:-5 to 0 to 5]
GColor Level For adjusting the color level.
Larger value : Increases the color level.
Smaller value : Decreases the color level.
[Setting range:-5 to 0 to 5]
53
HStabilizer This function prevents image shaking caused by vibration.
Set this function to A BOn to control image shaking.
Off : Disabled.
On : Enabled.
M
emo:
● When the function is set to A BOn , the screen is digitally zoomed to
approximately 1.3 times.
● Adjustment is disabled in the electronic zoom area.
● Adjustment is disabled for about 1 minute after power ON and during
Pan/Tilt/Zoom operation.
● Adjustment may not work when the vibration is fast. The effect can be
small when vibration direction does not match with Pan/Tilt position.
Depending on the installation environment, the stabilizer may malfunction
and increase image shaking due to the vibration transmitting to the
camera. In this case, set the stabilizer to A BOff .
IStabilizer Level This item allows you to set the adjustment level of the [Stabilizer] item H in 3
steps.
The adjustment volume is larger if the value is set to A BHigh rather than
A B A BMid . When it is set to Low , the adjustment volume is lesser than
compared to when it is set to A BMid .
[Setting value:Low,Mid,High]
JNoise Reduction When AOnB is set, image noise on the screen will be reduced.
M
emo:
● This item is only enabled when [AGC] item K is set to a value other than
A BOff .
● Image noise in dark images will be reduced but the resolution will
deteriorate.
● The edges between high and low illumination area may appear rough.
KALC For setting the priority of ALC (feature for maintaining the video level
according to the brightness of the object). You can select whether to assign
priority to the motion or picture quality when the object becomes dark.
Motion : Prioritizes movement.
When the object becomes dark, priority is given to AGC
(automatic gain control), and therefore this is suitable for
shooting fast-moving objects.
Quality : Prioritizes image quality.
When the object becomes dark, priority is given to the Sense
Up feature, and therefore this is suitable for shooting objects
requiring a high picture quality.
[Setting value:Motion,Quality]
54
Setting Using Internet Explorer
Camera Page (continued)
Setting (continued)
KALC (continued)
AGC For setting the AGC (automatic gain control) level.
Off : Disables the AGC feature
Mid : When the amount of light is insufficient
High : When the amount of light is particularly insufficient
Super : When the brightness level is insufficient even upon setting to
A BHigh .
[Setting value:Off, Mid, High, Super]
M
emo:
● The screen appears grainy at dark locations when the AGC feature is in
use.
Sense Up This feature is used to raise the sensitivity level by lengthening the
exposure time.
You can specify the number of times by which the sensitivity level is to be
increased automatically when the object becomes dark. When A Bx32 is
selected, the sensitivity is changed dynamically up to 32 times (as
compared to the A BOff mode) to fit to current darkness. When sensitivity
increases, the shutter speed becomes slower and hence, movement
becomes unnatural. When set to A BOff , Sense Up is disabled.
[Setting value:Off, x2, x4, x8, x16, x32, x64, x128]
M
emo:
● Upon raising the sensitivity level, the screen may appear grainy or
white, or white defects may occur. However, this is not a malfunction.
● When [Sense Up] is set to a value other than A BOff , flickers occur under
the light of fluorescent or mercury lamps. This is not a malfunction of
the camera, but is due to principles related to Sense Up.
● When the [Shutter Speed] item L is set to A B A B1/100 to 1/10000 , set
[Sense Up] to AOffB.
LShutter Speed This item sets the speed of the electronic shutter.
When [Sense Up] item K is set to A Bx2 or above, available setting value is
A B A B1/60 or 1/100 only.
[Setting value:1/60,1/100,1/250,1/500,1/1000,1/2000,1/4000,1/10000]
M
emo:
● Flickering of fluorescent lightings can be reduced when the shutter
speed is set to egions of commercial A1/100 1/60B or A B respectively in r
power frequency 50 Hz and 60 Hz.
● The faster the shutter speed is, a smear phenomenon specific to CCD,
where white bands appear vertically along bright light source, is more
emphasized.
● The edges between high and low illumination area may appear rough.
55
MB/W Mode This sets the function to switch from Color to B&W mode.
Color : Always be in Color mode.
Black & White : Always be in B&W mode.
Auto Low,Auto Mid,Auto High
: This item automatically switches between Color Mode
and B&W Mode when the luminance meets defined
conditions for over 30 seconds. Select the sensitivity from
three options.
M
emo:
To ensure a successful B&W/Color switching
● If the [B/W Mode] item is set to AAuto Low, Auto Mid, Auto HighB, the
B&W/Color setting can be switched according to the brightness of the
object, but the condition of illumination and field angle may make this
impossible. To be absolutely certain of B&W/Color switching,
connecting external sensor to alarm input cable of this camera and
setting alarm action of B&W mode is recommended.
IR Preset AF When switching the Color mode to B&W mode, the type of light source may
cause the focus to be dislocated. This is because the B&W mode is
sensitive to both visible light and near-infrared light. When this happens,
set this item to A BOn to focus automatically.
On : Enabled.
Off : Disabled.
Light This item sets the illumination of the object during B&W mode.
Normal : Select this for normal illumination.
IR : Select this when using infrared illumination.
M
emo:
● If A BIR is set under normal sunlight or fluorescent lighting, the camera
will not switch normally from Color to B&W mode.
56
Setting Using Internet Explorer
Encoding Page
This page is for setting JPEG and MPEG4 encoding parameters.
This page can be used during access using A Badmin or
A Boperator .
● Click [Advanced Settings] to display setting menu.
● Click [Encoding]. Press the [OK] button to enable the new settings. Press the [OK] button to enable
the new settings.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
● When settings on this page are altered during playback using Built-in Viewer, reboot the Built-in
Viewer.
● There is a maximum limit to the bit rate for transmission by the camera. If a bit rate that exceeds the
maximum limit is specified, this new setting will not be applied. For details on the maximum
transmission limit, refer to [Network Requirements] (A Page 33).
Setting (continued)
A
B
C D E F G
Click
AFrame Size For setting the frame size of each JPEG or MPEG4 screen to AVGAB (640 x
480) or AQVGAB (320 x 240).
Select one of the four different patterns.
57
JPEG
BQuality/Size For specifying the rate control mode and target file size for JPEG.
When AVFS1B to AVFS7B is selected, the quantization table during JPEG
encoding will be maintained and the file size will increase/decrease
according to the input signals. Stipulated values will be displayed in the Size
field. When recording JPEG data to a recorder with a limited storage
capacity, note that the maximum recording time may vary as the file size
fluctuates under this setting.
When AAFSB is selected, encoding is performed such that the target file size
is the average size of multiple JPEG images. You can enter the target size in
the [Size] field.
[Size field setting range for VGA: 10KB to 100KB (Only when setting
A
AFS
B
)]
[Size field setting range for QVGA: 3KB to 33KB (Only when setting
A BAFS )]
MPEG4
CBitrate For setting the MPEG4 encoding bit rate.
[Setting range:64kbps to 8000kbps]
DBitrate Control For selecting whether to set the MPEG4 rate control mode to CBR (Constant
Bit Rate) or VBR (Variable Bit Rate).
CBR : Encoding is performed at a fixed bit rate regardless of the
condition of the input video signals. Enables easy forecast of the
bit rate.
VBR : Changes the bit rate according to the condition of the input
video signals. Picture quality is stable, but forecast of the bit rate
is difficult.
EFPS For setting the MPEG4 frame rate.
[Setting range:1 fps, 7.5 fps, 10 fps, 15 fps, 25 fps, 30 fps]
FI Frame Interval For setting the I-frame interval. MPEG4 starts encoding from the I-frame.
Shortening the interval stabilizes the picture quality even when there are
rapid changes in the video image. However, the picture quality for images
with little change will deteriorate. In addition, when multicast packet loss
occurs, the time interval required to restore the image is shorter.
[Setting value:30, 60, 90, 120, 150]
GPriority For selecting whether to assign priority to the frame rate or picture quality
during MPEG4 encoding.
FPS : Assigns priority to frame rate. Select this setting to enable
smooth monitoring of motion images.
Quality : Prioritizes image quality.
M
emo:
● Valid when [Bitrate Control] D is A BCBR
. When a very small bit rate is set
for the frame rate or frame size, ACBRB or AVBRB will become the lowest
images and a difference will appear in the frame rate. which A BQuality
skips frames will be able to realize small bit rates better than AFPSB.
58
Setting Using Internet Explorer
Alarm Page
This page is for setting actions when there is an alarm.
Up to 5 actions (No. 01 to No. 05) may be set.
This page can be used during access using A Badmin or
A Boperator .
● Click [Advanced Settings] to display setting menu.
●
Click [Alarm]. Press the [OK] button to enable the new settings.
●
Press the [OK] button to enable the new settings. Only items that are valid under the selected action
will be saved. When Disable is selected for the action, all settings will be restored to their default
values.
● If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the
entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.
Setting (continued)
E
F
G
H
I
J
A B C D
Click
Produktspezifikationen
| Marke: | JVC |
| Kategorie: | Überwachungskamera |
| Modell: | VN-V685U |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JVC VN-V685U benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Überwachungskamera JVC
10 August 2024
8 August 2024
7 August 2024
6 August 2024
4 August 2024
3 August 2024
30 Juli 2024
26 Juli 2024
23 Juli 2024
20 Juli 2024
Bedienungsanleitung Überwachungskamera
- Überwachungskamera Samsung
- Überwachungskamera Approx
- Überwachungskamera Belkin
- Überwachungskamera Sanyo
- Überwachungskamera Exibel
- Überwachungskamera Gembird
- Überwachungskamera Genius
- Überwachungskamera Hama
- Überwachungskamera LogiLink
- Überwachungskamera Logitech
- Überwachungskamera Manhattan
- Überwachungskamera Nedis
- Überwachungskamera Niceboy
- Überwachungskamera Philips
- Überwachungskamera Sony
- Überwachungskamera Trust
- Überwachungskamera Panasonic
- Überwachungskamera Clas Ohlson
- Überwachungskamera Profile
- Überwachungskamera ZyXEL
- Überwachungskamera Bosch
- Überwachungskamera Laserliner
- Überwachungskamera Buffalo
- Überwachungskamera Canon
- Überwachungskamera Velleman
- Überwachungskamera Powerfix
- Überwachungskamera Eminent
- Überwachungskamera Linksys
- Überwachungskamera Maginon
- Überwachungskamera Netgear
- Überwachungskamera Technaxx
- Überwachungskamera Alecto
- Überwachungskamera Denver
- Überwachungskamera EMOS
- Überwachungskamera Gira
- Überwachungskamera König
- Überwachungskamera MarQuant
- Überwachungskamera Renkforce
- Überwachungskamera Thomson
- Überwachungskamera Trevi
- Überwachungskamera Blaupunkt
- Überwachungskamera Schneider
- Überwachungskamera Trebs
- Überwachungskamera Pyle
- Überwachungskamera Topcom
- Überwachungskamera Pioneer
- Überwachungskamera Motorola
- Überwachungskamera Xiaomi
- Überwachungskamera Abus
- Überwachungskamera Avidsen
- Überwachungskamera Elro
- Überwachungskamera EZVIZ
- Überwachungskamera Imou
- Überwachungskamera INSTAR
- Überwachungskamera Megasat
- Überwachungskamera Olympia
- Überwachungskamera Smartwares
- Überwachungskamera Switel
- Überwachungskamera Yale
- Überwachungskamera Ferguson
- Überwachungskamera Orion
- Überwachungskamera Gigaset
- Überwachungskamera Strong
- Überwachungskamera Toshiba
- Überwachungskamera Garmin
- Überwachungskamera Perel
- Überwachungskamera Netis
- Überwachungskamera Lindy
- Überwachungskamera Fenton
- Überwachungskamera Waeco
- Überwachungskamera Acme
- Überwachungskamera Burg Wächter
- Überwachungskamera Marmitek
- Überwachungskamera Marshall
- Überwachungskamera Honeywell
- Überwachungskamera B/R/K
- Überwachungskamera Marshall Electronics
- Überwachungskamera TRENDnet
- Überwachungskamera Targa
- Überwachungskamera First Alert
- Überwachungskamera AVerMedia
- Überwachungskamera Zebra
- Überwachungskamera TP-Link
- Überwachungskamera Flamingo
- Überwachungskamera Kodak
- Überwachungskamera Rollei
- Überwachungskamera IGet
- Überwachungskamera Adj
- Überwachungskamera Netatmo
- Überwachungskamera Duramaxx
- Überwachungskamera Ebode
- Überwachungskamera Xavax
- Überwachungskamera InFocus
- Überwachungskamera Overmax
- Überwachungskamera Monoprice
- Überwachungskamera Monacor
- Überwachungskamera JUNG
- Überwachungskamera Ednet
- Überwachungskamera AG Neovo
- Überwachungskamera Nest
- Überwachungskamera Edimax
- Überwachungskamera V-TAC
- Überwachungskamera Aritech
- Überwachungskamera Uniden
- Überwachungskamera Kogan
- Überwachungskamera Genie
- Überwachungskamera M-e
- Überwachungskamera Elmo
- Überwachungskamera Lumens
- Überwachungskamera Jablocom
- Überwachungskamera Conceptronic
- Überwachungskamera D-Link
- Überwachungskamera Eufy
- Überwachungskamera Stabo
- Überwachungskamera Friedland
- Überwachungskamera EVOLVEO
- Überwachungskamera SPC
- Überwachungskamera August
- Überwachungskamera Ring
- Überwachungskamera Digitus
- Überwachungskamera SereneLife
- Überwachungskamera Swann
- Überwachungskamera Vitek
- Überwachungskamera DataVideo
- Überwachungskamera LevelOne
- Überwachungskamera Aida
- Überwachungskamera APC
- Überwachungskamera Beafon
- Überwachungskamera Chuango
- Überwachungskamera Cisco
- Überwachungskamera Grandstream
- Überwachungskamera Delta Dore
- Überwachungskamera EVE
- Überwachungskamera Defender
- Überwachungskamera Tenda
- Überwachungskamera Swisstone
- Überwachungskamera Foscam
- Überwachungskamera Ubiquiti Networks
- Überwachungskamera Kramer
- Überwachungskamera Vaddio
- Überwachungskamera Intellinet
- Überwachungskamera Reolink
- Überwachungskamera Swan
- Überwachungskamera Hikvision
- Überwachungskamera FLIR
- Überwachungskamera Furrion
- Überwachungskamera Arlo
- Überwachungskamera Nexxt
- Überwachungskamera Planet
- Überwachungskamera EnGenius
- Überwachungskamera Dörr
- Überwachungskamera Lorex
- Überwachungskamera Ikan
- Überwachungskamera Comtrend
- Überwachungskamera Somfy
- Überwachungskamera Dahua
- Überwachungskamera Dedicated Micros
- Überwachungskamera DIO
- Überwachungskamera EasyN
- Überwachungskamera Escam
- Überwachungskamera EverFocus
- Überwachungskamera Ganz
- Überwachungskamera GeoVision
- Überwachungskamera Hombli
- Überwachungskamera Home Protector
- Überwachungskamera Iiquu
- Überwachungskamera Indexa
- Überwachungskamera Interlogix
- Überwachungskamera KlikaanKlikuit
- Überwachungskamera Kompernass
- Überwachungskamera Mr Safe
- Überwachungskamera Naxa
- Überwachungskamera Nordval
- Überwachungskamera Notifier
- Überwachungskamera Oplink
- Überwachungskamera Provision ISR
- Überwachungskamera Quantum
- Überwachungskamera Raymarine
- Überwachungskamera Revo
- Überwachungskamera SAB
- Überwachungskamera Satel
- Überwachungskamera SecurityMan
- Überwachungskamera Sinji
- Überwachungskamera SMC
- Überwachungskamera Sonic Alert
- Überwachungskamera Sricam
- Überwachungskamera Steren
- Überwachungskamera Storage Options
- Überwachungskamera Tenvis
- Überwachungskamera Hive
- Überwachungskamera Ubiquiti
- Überwachungskamera Vivotek
- Überwachungskamera Woonveilig
- Überwachungskamera Y-cam
- Überwachungskamera ACTi
- Überwachungskamera AVer
- Überwachungskamera Epcom
- Überwachungskamera ZKTeco
- Überwachungskamera AirLive
- Überwachungskamera Mobotix
- Überwachungskamera Dahua Technology
- Überwachungskamera Speco Technologies
- Überwachungskamera 3xLOGIC
- Überwachungskamera Atlantis Land
- Überwachungskamera CRUX
- Überwachungskamera Pentatech
- Überwachungskamera Summer Infant
- Überwachungskamera Illustra
- Überwachungskamera Surveon
- Überwachungskamera Avigilon
- Überwachungskamera Brilliant
- Überwachungskamera Hanwha
- Überwachungskamera Lanberg
- Überwachungskamera Verint
- Überwachungskamera Axis
- Überwachungskamera EtiamPro
- Überwachungskamera MEE Audio
- Überwachungskamera Advantech
- Überwachungskamera Chacon
- Überwachungskamera Alula
- Überwachungskamera EKO
- Überwachungskamera IOIO
- Überwachungskamera KJB Security Products
- Überwachungskamera BZBGear
- Überwachungskamera Adesso
- Überwachungskamera Brickcom
- Überwachungskamera Insteon
- Überwachungskamera Aigis
- Überwachungskamera Pelco
- Überwachungskamera ORNO
- Überwachungskamera Atlona
- Überwachungskamera Linear PRO Access
- Überwachungskamera Laxihub
- Überwachungskamera Valueline
- Überwachungskamera Aqara
- Überwachungskamera Tecno
- Überwachungskamera Lutec
- Überwachungskamera Brinno
- Überwachungskamera Night Owl
- Überwachungskamera WyreStorm
- Überwachungskamera Exacq
- Überwachungskamera Equip
- Überwachungskamera AVMATRIX
- Überwachungskamera UniView
- Überwachungskamera Alfatron
- Überwachungskamera Syscom
- Überwachungskamera BLOW
- Überwachungskamera Videotec
- Überwachungskamera DSC
- Überwachungskamera AViPAS
- Überwachungskamera Milestone Systems
- Überwachungskamera Inkovideo
- Überwachungskamera Hamlet
- Überwachungskamera Mobi
- Überwachungskamera Infortrend
- Überwachungskamera VideoComm
- Überwachungskamera Kguard
- Überwachungskamera Boyo
- Überwachungskamera HiLook
- Überwachungskamera Mach Power
- Überwachungskamera Canyon
- Überwachungskamera Digital Watchdog
- Überwachungskamera Ernitec
- Überwachungskamera Ikegami
- Überwachungskamera Gewiss
- Überwachungskamera Weldex
- Überwachungskamera Costar
- Überwachungskamera Sentry360
- Überwachungskamera ALC
- Überwachungskamera Spyclops
- Überwachungskamera Compro
- Überwachungskamera IDIS
- Überwachungskamera I3International
- Überwachungskamera B & S Technology
- Überwachungskamera Qian
- Überwachungskamera Accsoon
- Überwachungskamera Control4
- Überwachungskamera Petcube
- Überwachungskamera Apeman
- Überwachungskamera ATN
- Überwachungskamera IC Intracom
- Überwachungskamera POSline
- Überwachungskamera Watec
- Überwachungskamera ETiger
- Überwachungskamera Videcon
- Überwachungskamera BirdDog
- Überwachungskamera Topica
- Überwachungskamera Rostra
- Überwachungskamera Caddx
- Überwachungskamera Whistler
- Überwachungskamera ClearView
- Überwachungskamera Beseye
- Überwachungskamera IMILAB
- Überwachungskamera CNB Technology
- Überwachungskamera Tapo
- Überwachungskamera Securetech
- Überwachungskamera NetMedia
- Überwachungskamera Nivian
- Überwachungskamera Guardzilla
- Überwachungskamera Blink
- Überwachungskamera Zavio
- Überwachungskamera Campark
- Überwachungskamera IPX
- Überwachungskamera Annke
- Überwachungskamera AVTech
- Überwachungskamera Vimtag
- Überwachungskamera Security Labs
- Überwachungskamera Seneca
- Überwachungskamera Vosker
- Überwachungskamera Owltron
- Überwachungskamera Enabot
- Überwachungskamera Luis Energy
- Überwachungskamera Sir Gawain
- Überwachungskamera VisorTech
- Überwachungskamera Milesight
- Überwachungskamera GVI Security
- Überwachungskamera Conbrov
- Überwachungskamera HuddleCamHD
- Überwachungskamera Setti+
- Überwachungskamera BIRDFY
- Überwachungskamera I-PRO
- Überwachungskamera DVDO
- Überwachungskamera TCP
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024
11 Oktober 2024
11 Oktober 2024
11 Oktober 2024