Juki SC-910N Bedienungsanleitung
Juki
Nähmaschine
SC-910N
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Juki SC-910N (49 Seiten) in der Kategorie Nähmaschine. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/49
ENGLISH
SC-910N
INStruCtIoN MaNuaL
i
CONTENTS
!. SPECIFICATIONS ..................................................................................... 1
@. SET-UP ...................................................................................................... 1
1. Installing M91 small sized motor unit ...............................................................................................1
2. Installing to the table ..........................................................................................................................2
3. Adjusting the belt (when M91 is used) ..............................................................................................2
4. Adjusting the belt cover (when M91 is used) ...................................................................................3
5. Connecting the cords .........................................................................................................................4
6. Attaching the connecting rod .......................................................................................................... 11
7. Setting procedure of the machine head ......................................................................................... 12
8. Machine head list ..............................................................................................................................13
9. Adjusting the machine head (DDL-9000A only) .............................................................................14
#. FOR THE OPERATOR ............................................................................ 15
1. Operating procedure of SC-910N ....................................................................................................15
2. Explanation of the operation panel .................................................................................................17
3. Operating procedure of the sewing pattern ...................................................................................18
(1) Reverse stitching pattern ..............................................................................................................18
(2) Overlapped stitching pattern ......................................................................................................... 19
(3) Special setting ..............................................................................................................................20
4. Setting for functions of SC-910N .....................................................................................................22
5. Function setting list ..........................................................................................................................24
6. Detailed explanation of selection of functions .............................................................................. 31
7. Automatic compensation of neutral point of the pedal sensor ................................................... 40
8.Selectionofthepedalspecications ..............................................................................................40
9. Setting of the auto lifter function .................................................................................................... 41
10. Connection of the pedal of standing-work machine .....................................................................41
11. External input / output connector ...................................................................................................42
12. Connection of the material end sensor (ED) ..................................................................................42
13. Initialization of the setting data .......................................................................................................43
$. MAINTENANCE ...................................................................................... 44
1. Removing the rear cover ..................................................................................................................44
2. Replacing the fuse ...........................................................................................................................44
3. Error codes ........................................................................................................................................45
– 1 –
ENGLISH
!. SPECIFICATIONS
@. SET-UP
SC-910N control box can be used for DD (direct-drive) system machine head and the belt-drive system
machine head by connecting the separately-available small-sized motor unit (M91).
When using the small-sized motor unit, it is necessary to install the motor unit to the control box before in-
stalling the control box to the table.
Install the motor unit to the control box following the instructions below.
SC-910N control box
M91 small-sized motor unit (separately-available article)
1. Installing M91 small sized motor unit
1) Lay down the control box while the rear cover is
placed under the control box.
2) Remove tie-mount A.
3) Adjust the hole section of the installing base of
M91 to the hole section of the installing plate.
4) Temporarily tighten ve places with counter-sunk
screws 1 supplied with the unit as accessories.
5) Securely tighten them with hexagonal wrench
key 2 supplied with the unit as accessories.
(Caution) 1. When tightening the screw, se-
curely insert the hexagonal wrench
key into the screw hole section to
tighten.
2. Hexagonal wrench key is attached
to M91.
3. Be careful that the motor shaft does
not hit against anything. (If a strong
shock is given to the motor shaft,
there is the possibility that the mo-
tor is damaged.)
Supply voltage Single phase 100 to 120V 3-phase 200 to 240V Single phase 200 to 240V
Frequency 50Hz/60Hz 50Hz/60Hz 50Hz/60Hz
Operating envi-
ronment
Temperature : 0 to 40˚C
Humidity : 90% or less
Temperature : 0 to 40˚C
Humidity : 90% or less
Temperature : 0 to 40˚C
Humidity : 90% or less
Input 350VA 350VA 350VA
1
2
A
Produktspezifikationen
| Marke: | Juki |
| Kategorie: | Nähmaschine |
| Modell: | SC-910N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Juki SC-910N benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nähmaschine Juki
5 Oktober 2024
5 September 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
28 August 2024
21 August 2024
21 August 2024
21 August 2024
Bedienungsanleitung Nähmaschine
- Nähmaschine Sinbo
- Nähmaschine Emerio
- Nähmaschine Tristar
- Nähmaschine Medion
- Nähmaschine SilverCrest
- Nähmaschine Bestron
- Nähmaschine Guzzanti
- Nähmaschine AEG
- Nähmaschine Alfa
- Nähmaschine Ambiano
- Nähmaschine Siemens
- Nähmaschine Jata
- Nähmaschine Lervia
- Nähmaschine IKEA
- Nähmaschine Durabase
- Nähmaschine Blaupunkt
- Nähmaschine Hema
- Nähmaschine Home Electric
- Nähmaschine Micromaxx
- Nähmaschine Mio Star
- Nähmaschine Solac
- Nähmaschine Privileg
- Nähmaschine Livoo
- Nähmaschine Easy Home
- Nähmaschine Prixton
- Nähmaschine Lifetec
- Nähmaschine Singer
- Nähmaschine Husqvarna
- Nähmaschine Termozeta
- Nähmaschine Crofton
- Nähmaschine Brother
- Nähmaschine Kohler
- Nähmaschine Primera
- Nähmaschine Veritas
- Nähmaschine Toyota
- Nähmaschine Janome
- Nähmaschine Victoria
- Nähmaschine Kayser
- Nähmaschine Jocca
- Nähmaschine Aigger
- Nähmaschine EasyMaxx
- Nähmaschine Bernina
- Nähmaschine Elna
- Nähmaschine Necchi
- Nähmaschine Pfaff
- Nähmaschine Dürkopp Adler
- Nähmaschine W6
- Nähmaschine E&R
- Nähmaschine Carina
- Nähmaschine Empisal
- Nähmaschine ER
- Nähmaschine Feiyue
- Nähmaschine Gritzner
- Nähmaschine Hofmann
- Nähmaschine Huskystar
- Nähmaschine Husqvarna-Viking
- Nähmaschine Kenmore
- Nähmaschine Lewenstein
- Nähmaschine Mediashop
- Nähmaschine Muller
- Nähmaschine Novamatic
- Nähmaschine Siemssen
- Nähmaschine Silver
- Nähmaschine Sinojo
- Nähmaschine Tesco
- Nähmaschine Vendomatic
- Nähmaschine Weasy
- Nähmaschine Yamata
- Nähmaschine Zippy
- Nähmaschine Union Special
- Nähmaschine Kunft
- Nähmaschine Meister Craft
- Nähmaschine RCE
- Nähmaschine Yamato
- Nähmaschine Baby Lock
- Nähmaschine Łucznik
- Nähmaschine Anker-Bernette
- Nähmaschine LERAN
- Nähmaschine Prince
- Nähmaschine Bernette
- Nähmaschine Sewmaq
- Nähmaschine SteamMax
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024