JL Audio MX280/4 Bedienungsanleitung

JL Audio Empfänger MX280/4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio MX280/4 (2 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Thank you for purchasing a JL Audio amplifier for
your sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment. For maximum
performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at technical@jlaudio.com or call (954) 443–1100 during business hours.
OWNER’S MANUAL
280W Full-Range 4-Channel Class D Amplier
What’s Included
(1) Amplifier
(4) Stainless steel mounting screws
(1) Spare 35A fuse
(1) User manual
Product Description
This is a four-channel, full-range audio amplifier utilizing Class D technology for
all channels.
Installation Applications
This amplifier is designed for operation with 12 volt, negative-ground electrical
systems. Using this product in systems with positive ground and/or voltages
other than 12V may result in damage to the product and will void the warranty.
This product is not certified or approved for use in aircraft.
Safety Considerations
• Whenever possible, mount the amplifier in a dry, well-ventilated location
that does not interfere with other factory installed electronic devices. If a dry
environment is not available, a location that is not exposed to heavy splashing
may be used.
• While this amplifier is designed to be water-resistant, it should never be
submerged under water or subjected to high-pressure water spray. Do not
install where it will be directly exposed to the elements.
• Do not mount the amplifier in the engine compartment or in any areas of
extreme heat.
• Securely mount the amplifier so that it does not come loose in the event of
a collision/sudden jolt or as a result of repeated vibrations during normal
operation.
• Check before drilling to make sure that you will not be drilling into an exterior
panel/hull, fuel tank, gas/brake line, wiring harness, or other vital system.
• Do not run system wiring outside or underneath the vehicle/vessel. This is an
extremely dangerous practice, which can result in severe damage/injury.
• Protect all system wires from sharp edges (metal, fiberglass, etc.) by carefully
routing them, tying them down and using grommets and loom where
appropriate.
• Secure all wiring as needed, using cable ties or wire clamps to protect them
from moving parts and sharp edges.
Installation Procedure/Connections
1. Disconnect the NEGATIVE battery post connection and secure the discon-
nected cable to prevent accidental reconnection during installation. This is
an essential safety precaution during installation!
2. Connect the RED power lead to the positive (+12V) battery post. 8 AWG is
the minimum power wire size for this amplifier.
3. An appropriate fuse at the main power wire(s) to the amplifier(s) is vital for
vehicle/vessel safety. This fuse must be installed within 18 inches (45 cm) of
the positive battery post connection. If this is the only device connected to
this main wire, use a 35A fuse. Do not install the fuse until the power wire
has been securely connected to the amplifier.
4. Connect the BLACK negative ground lead to a clean, solid metal grounding
point near the amplifier. This can be to metal chassis ground, if available. If
no metal chassis ground is available, it may be necessary to make this con-
nection to the NEGATIVE battery post. 8 AWG is the minimum ground wire
size for this amplifier. All ground connections (source unit and amplifi-
ers) should be made at the same location.
5. Connect the BLUE remote turn-on lead to the source unit’s positive (+12V)
remote turn-on output. If your source unit does not have a dedicated
remote turn-on output, the amplifier’s turn-on lead can be connected to
+12V via a switch that derives power from an ignition-switched circuit.
6. Signal Input (Low-Level): Connect the amplifier’s RCA input jacks to the
source unit’s preamp level output jacks.
7. Signal Input (Hi-Level): If your source unit does not offer preamp level signal
outputs, you can splice the speaker output wires of the source unit onto a
pair of RCA plugs for each input pair or use the JL Audio ECS Speaker Wire
to RCA adaptor (XD-CLRAIC2-SW). Make sure to observe correct polarity in
making “Hi-Level Input” connections. Failure to do so will result in a loss of
signal (poor performance).
8. Connect the speaker output leads to the corresponding speaker wires.
9. Make necessary adjustments to the filter controls and input sensitivity.
WARNING! Failure to make safe, tight, high-integrity power connections
can result in fire and extensive damage!
Control Setting Mode / Function
Channel Mode
2CH #1) 4 Stereo Outputs (non-fading) Use Front
Inputs Only
#2) 2 Bridged Mono Outputs
3CH #1) 2 Stereo Front + 2 Mono Rear Outputs Use Front
Inputs Only
#2) 2 Stereo Front + 1 Bridged Mono Rear Output
4CH
#1) 4 Stereo Outputs (fading) Use Front and Rear Inputs
#2) 2 Bridged Stereo Outputs Left to Both
Front Inputs
Right to Both
Rear Inputs
Front
or
Rear
Input
Voltage
Low RCA/Preamp Level Range (250 mV - 4 V)
High RCA/Preamp or Speaker Level Range (750 V - 15 V)
Filter
Mode
Off Full-Range Operation of Input Signals
HP (High-Pass) Configures Filter to Attenuate Frequencies BELOW
the Selected Filter Frequency
LP (Low-Pass) Configures Filter to Attenuate Frequencies ABOVE
the Selected Filter Frequency
Filter
Freq. Variable Adjusts the filter cutoff frequency of the selected Filter Mode,
variable from 35-300 Hz, 12 dB/Octave
Input
Sens. Variable
Adjusts the input stage of each pair of amplifier channels to
match the source unit’s output voltage for maximum clean
output (refer to Appendix A)
Control Panel Settings and Adjustments
The amplifier’s settings and controls are located on the bottom panel beneath a
gasketed, protective cover. Remove the four Phillips head screws from the center
panel to access the controls and make adjustments. Replace cover when finished
and mount the amplifier.
Specications MX280/4
Rated RMS Power @ 14.4V,
<1% THD+N
50W x 4 @ 4 Ω 64W x 4 @ 3 Ω
70W x 4 @ 2 Ω 140W x 2 @ 4 Ω Bridged
Rated RMS Power @ 12.5V,
<1% THD+N
36W x 4 @ 4 Ω 47W x 4 @ 3 Ω
52W x 4 @ 2 Ω 100W x 2 @ 4 Ω Bridged
Frequency Response 20 Hz - 20 kHz (+0, -1dB), 6.3 Hz - 30 kHz (+0, -3dB)
S/N Ratio, A-weighted,
20 kHz noise bandwidth 89.5 dB (Referred to rated power), 70.5 dB (Referred to 1 W)
Damping Factor >60 / 50 Hz @ 4 Ω, >30 / 50 Hz @ 2 Ω
Input Voltage Range 250 mV - 4 V (Low) or 750 mV - 15 V (High)
Filter Modes Low-Pass or High-Pass, defeatable
Filter Freq. Range, Slope 35 - 300 Hz, 12 dB/Octave
Detented Filter Frequency
Potentiometers 35, 80, 135, 300 Hz (Calibrated)
Input Mode Switch 2 / 3 / 4 Channel
Min Power/GND Wire 8 AWG
Fuse Rating 35A
Dimensions 1.77 in x 8.66 in 3.09 in / 45 mm x 220 mm x 78.5 mm
Status LED’s / Protection Circuitry
There are two status indicator lights on the wiring end panel of the amplifier.
1. “POWER” (Green): Lights to indicate that the amplifier is turned on and
operating normally.
2. “PROTECT” (Red): Lights to indicate the amplifier’s protection circuitry
has been activated to prevent product failure due to thermal overload,
over current or short-circuit to the amplifier’s outputs. When this pro-
tection mode is activated, the amplifier will shut down to protect its
circuitry. When the problem is corrected, the amplifier will return to
normal operation and the “Protect” LED will shut off. Connecting the
speaker outputs to impedances lower than 2 ohms stereo (4 ohms
bridged) will also cause this protection mode to activate.
POWER
(Green LED)
PROTECT
(Red LED) Status Note
ON OFF Normal Operation
OFF ON Thermal Protection Lasts until temp cools to normal
OFF/ON ON/OFF Over Current Green/Red LEDs alternate for 1 second
OFF ON Short Circuit Possible audible “popping” noise
Remote Turn-On
35A
High Low-Level Inputs Speaker<or>
Outputs
(selectable via Input Voltage Switch
for each channel pair)
[+12V]
[GND]
Battery
[FR–]
[FR+]
[RL–]
[RL+]
[RR–]
[RR+]
[FL–]
[FL+]
[REAR IN]
Source [REM]
[FRONT IN]
Label Wire Color Description
+12V Red Positive (+12V) Power Connection
GND Black Negative (GND) Ground Connection
REM Blue Positive (+12V) Remote Turn-On Input
FL+ White Ch. 1
output
(+) Positive Front Left Speaker Front Bridged (+)
FL– White/Black (–) Negative Front Left Speaker
FR+ Gray Ch. 2
output
(+) Positive Front Right Speaker
FR– Gray/Black (–) Negative Front Right Speaker Front Bridged (–)
RL+ Green Ch. 3
output
(+) Positive Rear Left Speaker Rear Bridged (+)
RL– Green/Black (–) Negative Rear Left Speaker
RR+ Purple Ch. 4
output
(+) Positive Rear Right Speaker
RR– Purple/Black (–) Negative Rear Right Speaker Rear Bridged (–)
Label Plug Description
FRONT
IN
White RCA Ch. 1 / Front Left Channel Signal Input
Red RCA Ch. 2 / Front Right Channel Signal Input
REAR
IN
White RCA Ch. 3 / Rear Left Channel Signal Input
Red RCA Ch. 4 / Rear Right Channel Signal Input
Connections
IPX6
WATER
RESISTANT
ENGLISH ESPAÑOL FRANCAIS DEUTSCH
FL+ White Blanco Blanc Weiß
FL– White/Black Blanco/Negro Blanc/Noir Weiß/Schwarz
FR+ Gray Gris Gris Grau
FR– Gray/Black Gris/Negro Gris/Noir Grau/Schwarz
RL+ Green Verde GrünVert
RL– Green/Black Verde/Negro Vert/Noir Grün/Schwarz
RR+ Purple Púrpura Violet Lila
RR– Purple/Black Púrpura/Negro Violet/Noir Lila/Schwarz
Problem Possible Cause Solution
How to properly set
input sensitivity
Please refer to Appendix A to set the
input sensitivity for maximum, low-
distortion output.
Amplifier doesn’t
turn on
Faulty fuse Remove fuse and check with continuity
meter. Replace if necessary.
Poor connection
integrity
Check “+12V”, “Ground”, and “Remote”
leads for pinched wires; ensure tight
connections.
Insufficient “Remote”
input
Make sure there is a sufficient +12V
supply at the “Remote” connection; if
not a relay may be required.
Intermittent output,
fluctuates when I tap
on it or hit a bump
Poor connection
integrity
Make sure insulation has been properly
stripped back at connection points for
good contact area.
Make sure input connectors are making
good contact with input jacks of the
amplifier.
Distorted, attenuated,
or popping sound
Faulty speaker
connection (Short
Circuit / Over Current
Protection)
Inspect speaker wires for possible
short-circuit, either together or shorted
to the vehicle’s chassis ground.
Check the nominal load impedance at
the amplifier is equal to or greater than
2 ohms stereo (4 ohms bridged).
Output shuts off after
a while
Overheating
condition (Thermal
Protection)
Make sure amplifier mounting area has
adequate space for ventilation and heat
dissipation.
Limited Warranty – Amplifiers (USA)
JL Audio warrants this product to be free of defects in materials and
workmanship for a period of two (2) years from the original date of purchase.
This warranty is not transferrable and applies only to the original purchaser
from an authorized JL Audio dealer. Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction, JL
Audio will (at its discretion), repair or replace the defective product with new
or remanufactured product at no charge. Damage caused by the following is
not covered under warranty: accident, misuse, abuse, product modification or
neglect, failure to follow installation instructions, unauthorized repair attempts,
misrepresentations by the seller. This warranty does not cover incidental or
consequential damages and does not cover the cost of removing or reinstalling
the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the
express warranty as provided herein beginning with the date of the original
purchase at retail, and no warranties, whether express or implied, shall apply
to this product thereafter. Some states do not allow limitations on implied
warranties, therefore these exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights, which vary from
state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio ’s Amplifier Service Facility
freight-prepaid through an authorized JL Audio dealer and must be
accompanied by proof of purchase (a copy of the original sales receipt). Direct
returns from consumers or non-authorized dealers will be refused unless
specifically authorized by JL Audio with a valid return authorization number.
Warranty expiration on products returned without proof of purchase will be
determined from the manufacturing date code. Coverage may be invalidated
as this date is previous to purchase date. Non-defective items received will
be returned freight-collect. Customer is responsible for shipping charges and
insurance in sending the product to JL Audio. Freight damage on returns is not
covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy.
Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
Do not increase any “Input Sens.” setting for any amplifier channel or
channel pair in the system beyond the maximum level established during
this procedure. Doing so will result in audible distortion and possible
speaker damage.
It will be necessary to re-adjust the “Input Sens.” for the affected channels if any
equalizer boost is activated after setting the “Input Sens.” with this procedure. This
applies to any EQ boost circuit, including source unit tone controls or EQ circuits. EQ
cuts will not require re-adjustment.
MX280/4
Nom. Impedance Target AC Voltage
4Ω 14.1 V
2Ω 11.8 V
Bridged to 4Ω 23.7 V
Rea r [ REAR IN]
[FRONT IN]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Sou r ce
(Not Used)
[FR–]
[FR+]
[R L–]
[R L+]
[R R–]
[R R+]
[FL–]
[FL+]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Fro nt
Amplifier Inputs Speaker Outputs
4 Stereo Outputs (non-fading)
Channel Mode: 2CH
Inputs: Use Front Inputs Only
RMS Power: 50W x 4 @ 4 Ω (70W x 4 @ 2 Ω)
Rea r [ R EAR IN]
[FRONT IN]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Sou r ce
[FR–]
[FR+]
[R L–]
[R L+]
[R R –]
[R R +]
[FL–]
[FL+]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Fro nt
Amplifier Inputs Speaker Outputs
4 Stereo Outputs (fading)
Channel Mode: 4CH
Inputs: Use Front and Rear Inputs
RMS Power: 50W x 4 @ 4 Ω (70W x 4 @ 2 Ω)
Rea r [ REAR IN]
[FRONT IN]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Sou r ce
(Not Used)
[FR–]
[FR+]
[R L–]
[R L+]
[R R–]
[R R+]
[FL–]
[FL+]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Fro nt
Amplifier Inputs Speaker Outputs
2 Bridged Mono Outputs
Channel Mode: 2CH
Inputs: Use Front Inputs Only
RMS Power: 140W x 2 @ 4 Ω
[R E AR IN]
[FRONT IN]
Sou r ce
Fro nt
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
[FR–]
[FR+]
[R L–]
[R L+]
[R R –]
[R R +]
[FL–]
[FL+]
White
Y-Adaptor
Y-Adaptor
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Amplifier Inputs Speaker Outputs
2 Bridged Stereo Outputs
Channel Mode: 4CH
Inputs: Left Signal to Both Front Inputs / Right
Signal to Both Rear Inputs
RMS Power: 140W x 2 @ 4 Ω
Rea r [ REAR IN]
[FRONT IN]
Sou r ce
(Not Used)
Fro nt
White
White/Black
Gray
Gray/Black [FR–]
[FR+]
[FL–]
[FL+]
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
[R L–]
[R L+]
[R R–]
[R R+]
Green
Green/Black
Purple
Purple/Black
2 Stereo Front + 1 Bridged Mono Rear
Output
Channel Mode: 3CH
Inputs: Use Front Inputs Only
RMS Power: 50W x 2 @ 4 Ω (70W x 2 @ 2 Ω) + 140W
x 1 @ 4 Ω
Amplifier Inputs Speaker Outputs
Amplifier Inputs Speaker Outputs
2 Stereo Front + 2 Mono Rear Outputs
Channel Mode: 3CH
Inputs: Use Front Inputs Only
RMS Power: 50W x 4 @ 4 Ω (70W x 4 @ 2 Ω)
Rear [RE AR IN]
[FRONT IN]
Source
(Not Used)
Front
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
[FR–]
[FR+]
[FL–]
[FL+]
[R L–]
[R L+]
[R R –]
[R R +]
Troubleshooting
Appendix A:
Input Sensitivity Level Setting
Following the directions below will allow the installer to adjust the input
sensitivity of each amplifier channel pair in just a few minutes using equipment
commonly available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
• CD or file with a sine-wave test tone recorded at 0 dB reference level in the
frequency range to be amplified for that set of channels (50 Hz for subwoofer
channels, 1 kHz for a midrange application). Do not use attenuated test tones
(-10 dB, -20 dB, etc.).
The Nine-Step Procedure
1) Disconnect the speakers from the amplifier’s speaker output connec-
tors (you need only disconnect one wire on each output).
2) Turn off all processing (bass/treble, loudness, EQ, etc.) on the source
unit, processors (if used) and amplifier. Set the source unit’s fader con-
trol to center position and its subwoofer level control to 3/4 of maxi-
mum.
3) Turn the “Input Sens.” control all the way down.
4) Set the source unit volume to 3/4 of full volume. This will allow for rea-
sonable gain overlap with moderate clipping at full volume.
5) Using the chart on this page, determine the target voltage for input
sensitivity adjustment according to the nominal impedance of the
speaker system connected to the amplifier outputs.
6) Verify that you have disconnected the speakers before proceeding. Play
a track with an appropriate sine wave (within the frequency range to
be amplified) at 3/4 source unit volume.
7) Connect the AC voltmeter to the speaker output connectors of the
amplifier. Make sure you test the voltage at the correct connectors
(+ and –).
8) Increase the “Input Sens.” control until the target voltage is observed
with the voltmeter.
9) Once you have adjusted the amplifier to its maximum low-distortion
output level, reconnect the speaker(s) and listen to the system. The
“Input Sens.” controls can now be adjusted downward if the amplifier
requires attenuation to achieve the desired system balance.

Produktspezifikationen

Marke: JL Audio
Kategorie: Empfänger
Modell: MX280/4

Brauchst du Hilfe?

Wenn Sie Hilfe mit JL Audio MX280/4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger JL Audio

JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
JL Audio

JL Audio HD Series HD600/4 Bedienungsanleitung

7 Oktober 2024
JL Audio

JL Audio MV400/4i Bedienungsanleitung

2 Oktober 2024
JL Audio

JL Audio MV700/5i Bedienungsanleitung

19 September 2024
JL Audio

JL Audio XDM600/6 Bedienungsanleitung

15 September 2024
JL Audio

JL Audio XDM800/8-24V Bedienungsanleitung

5 September 2024
JL Audio

JL Audio XDM600/6-24V Bedienungsanleitung

5 September 2024
JL Audio

JL Audio MHD600/4-24V Bedienungsanleitung

29 August 2024
JL Audio

JL Audio MX500/1 Bedienungsanleitung

12 August 2024
JL Audio

JL Audio XD600/6v2 Bedienungsanleitung

6 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024
Avantree

Avantree Oasis Plus Bedienungsanleitung

7 Oktober 2024