Jensen JS65T Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Jensen JS65T (8 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
TRIAXIAL SERIES
TRIAXIAL SERIES
TRIAXIAL SERIES
TRIAXIAL SERIES TRIAXIAL SERIES
INSTALLATION/OWNER'S MANUAL
Car Audio Speakers
2
Safety Guidelines
Thank you for the JS ar peakers. purchasing Jensen Triaxial Series C S Although
Jensen to sure all of the contained this has attempted make information within
manual please any subject without is accurate, be aware that part of it is to change
notice.
The following instructions should be used a general guideline only.
If you are unsure about performing any of the procedures listed
below, please consult a professional car audio installation center.
Before installation, please follow these guidelines:
1. Be sure to carefully read and understand the instructions before attempting to install
this product.
2. For safety, disconnect the negative terminal from the battery prior to beginning the
installation.
3. To ensure an obstacle-free fit, check and double check mounting depth of the
speakers against available depth, as well as the location of window mechanics, door
handles, and window handles.
4. Use caution before you drill or cut! Be careful not to cut or drill into gas tanks, fuel
lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any
vehicle.
5. Never run speaker wires underneath your vehicle. Running speaker wires inside the
vehicle provides the best protection from exhaust heat and environmental elements.
6. Avoid running wires over, near, or through sharp edged surfaces. Use rubber
grommets to protect any wires routed through metal.
7. When running the speaker cable from the amplifier, avoid running it near sources of
high current (i.e. wiring harnesses, battery cables).
8. If using provided grilles, be sure mounting location is sufficient distance from door
and/or window handles.
PREPARATION
3
INSTALLATION
%DVLF,QVWDOODWLRQ6WHSV
%DVLF,QVWDOODWLRQ6WHSV
%DVLF,QVWDOODWLRQ6WHSV
%DVLF,QVWDOODWLRQ6WHSV%DVLF,QVWDOODWLRQ6WHSV
•Connect the speaker outputs from the head unit to the speakers.
•In some vehicles, it may be possible to utilize the existing speaker wiring. When doing
this, be cautious of the polarity (+/-) of the speaker wires, as these wire colors vary for
each vehicle.
Tip: Using factory wiring harness adapters for the head unit and speakers can help
eliminate wiring issues.
•In some vehicles, it may be necessary to run new speaker wire throughout the vehicle.
Observe caution when routing wires.
•Always use quality connectors that fit tightly, or solder each connection. It may be
necessary to waterproof connections made inside door panels.
•Wiring speakers out-of-phase (the polarity of one speaker is wrong) will cause the
speakers to sound poor, and have very little bass response.
Step 1
Step 1
Step 1
Step 1Step 1: Remove existing speaker.
Step 2
Step 2
Step 2
Step 2Step 2: Position new speaker and align with existing mounting holes.
Step 3
Step 3
Step 3
Step 3Step 3: Attach the positive (+) and negative (-) speaker terminals
(see FIGURE 2). Be sure to observe proper polarity when connecting the wires
(the striped wire is the negative lead).
FIGURE 1 - DOOR PANEL INSTALLATION
Speaker Door PanelGrille
FIGURE 2 - CONNECTING SPEAKER WIRES
FIGURE 3 - REAR DECK INSTALLATION


Produktspezifikationen

Marke: Jensen
Kategorie: Lautsprecher
Modell: JS65T

Brauchst du Hilfe?

Wenn Sie Hilfe mit Jensen JS65T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher Jensen

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-