JBL MR26 Bedienungsanleitung


Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r JBL MR26 (8 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war fĆ¼r 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
MR SERIES
LOUDSPEAKERS
OWNERā€™S
MANUAL
MR
M5
MR25
MR26
MR28
MR38
MR308II
MR310II
MR Center
S E R I E S
INTRODUCTION
Congratulations on choosing JBL MR
Series Loudspeakers. Their highly
accurate, uncolored and balanced
sound character will greatly increase
your enjoyment of recorded music
and movies. JBL speakers are built
with careful attention to detail, using
only the highest quality materials.
They will provide many years of
excellent performance.
The MR Series is the result of com-
bining traditional JBL Signature
Sound performance values with ele-
gant contemporary appearance.
Maximum Radiating Surface Area:
MR Series transducers utilize new
transducer technology by extending
the surface area of the cone allow-
ing for a shorter excursion of the
driver without sacriļ¬cing critical air
movement.
Maximum Efficiency: Larger air
movement coupled with shorter coil
movement allows the MR transducers
to be very efficient. See specifications.
Maximum Transducer Control:
Reduces distortion by tightening
the control of driver excursion and
increasing driver linearity.
Smooth, Accurate, Extended
Response: The MR series trans-
ducers, computer-optimized dividing
networks, and bass reļ¬‚ex cabinets
combine to give clear, crisp, accu-
rate, JBL Signature Sound.
PLACEMENT
Bookshelf Models: For the best
stereo reproduction, the two loud-
speaker systems should be an equal
distance from your listening position
and separated so that the angle
between them, at the listening posi-
tion, is between 40 and 60 degrees
(see Fig. 1). For example, if your lis-
tening position is 8 to 12 feet (2.5m
to 4m) from each speaker, the two
systems should be about 8 feet
(2.5m) apart. Placing the loudspeak-
ers in corners or against a wall will
result in the strongest (not necessa-
rily the most accurate) bass. Except
for the M5, all MR Series speakers
have their ports in the front so you
can place the rear of the speaker up
against a wall. In the case of the M5,
do not place the speaker closer than
3 inches (75mm) to the wall behind it
if possible.
For the best stereo imaging, we rec-
ommend that the systems be placed
so that the high frequency transduc-
ers are positioned approximately at
ear level of a seated listener. Every
room is diļ¬€erent and there are diļ¬€er-
ent tastes, so donā€™t hesitate to experi-
ment on your own.
Tower Models: The Tower models
cabinet height and driver placement
allow for speaker placement directly
on the ļ¬‚oor. For the best stereo
reproduction, the two loudspeaker
systems should be an equal distance
from your listening position and sepa-
rated so that the angle between
40Ā°-60Ā°
Fig. 1
2
them, at the listening position, is
between 40 and 60 degrees. For
example, if your listening position is
8 to 12 feet (2.5m to 4m) from each
speaker, the two systems should be
about 8 feet (2.5m) apart.
Center Channel Model: As the
center channel contains the dialog
and other central action sounds, the
speaker should be located very close
to the Monitor/TV and centered with
the Monitor/TVā€™s center line. Place
the MR Center directly on top of or
directly below the Monitor/TV with the
front edge of the speaker grille ļ¬‚ush
with the edge of the Monitor/TV. You
should have your Left and Right
speakers within a 2 ft or less height
range of your Center Channel for
proper sonic performance (see Fig 2).
In Case Color Interference Occurs:
The speaker is shielded to work with
video applications, however some
color interference may be observed
on the TV screen depending on the
type of your TV set. If color interfer-
ence is observed, turn your TV oļ¬€ for
15 minutes and move the speaker
back about 1" from the front edge of
the TV. Turn on TV and recheck. If
this is not far enough, move back fur-
ther and experiment until the interfer-
ence disappears. You may have to
turn the TV oļ¬€ for a few minutes and
turn it on again to clear the screen.
CONNECTIONS
To connect the loudspeaker systems
to the receiver or ampliļ¬er, use two-
conductor insulated wire. Your JBL
dealer can recommend suitable
cables, or you can buy wire at most
hardware or electronic stores. We
recommend #16 AWG wire as a mini-
mum size. If your speaker is more
than 30 feet (10m) from your receiver
or ampliļ¬er, use larger diameter
lower gauge wire. Connections are
made at the terminals located on the
back of the MR Series speakers.
Preparing the Hookup Wire
Carefully plan your wire lengths
before cutting any speaker wire.
Be sure to allow plenty of extra
wire to help hide paths in corners,
along baseboards, etc.
1. For Left and Right Speakers, ļ¬rst
determine the wire length needed
between the most distant speaker
and the receiver or ampliļ¬er.
2. Now make the hookup wires for
both speakers this length, even if one
loudspeaker is much closer to your
ampliļ¬er than the other. This will
help maintain proper signal balance.
(For the MR Center, determine the
length needed from AV receiverā€™s
center channel output to speaker).
3. Strip oļ¬€ 3
ā„8" of insulation from both
ends of each conductor.
4. Twist each set of thin wires into a
tightly-bunched spiral.
5. At this point you need to identify a
visual diļ¬€erence between the two
conductors of each molded pair of
speaker wire. Diļ¬€erentiating marks
can be a diļ¬€erent color wire (copper
or ā€œsilverā€); a strand of yarn in one
conductor; thin, raised ribs on one
MR SERIES LOUDSPEAKERS
3
(2 ft. or less)
(2 ft. or less)
Fig. 2


Produktspezifikationen

Marke: JBL
Kategorie: Lautsprecher
Modell: MR26

Brauchst du Hilfe?

Wenn Sie Hilfe mit JBL MR26 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher JBL

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung fĆ¼r -Kategorien-