JBL Control 85M Bedienungsanleitung

JBL Lautsprecher Control 85M

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr JBL Control 85M (7 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war fĂĽr 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
Twist the top part of the enclosure in a
clock-wise direction until it disengages
from the bottom part.
Lift o the top section.
Control 85M/88M Mushroom Landscape Speaker
Installation Instructions
12
Before nal assembly and installation of the Landsape speaker, it is important to prepare the installation site. The speaker is
designed to be able to sit below grade, with the lower half burried in the soil no deeper than the boundary point where the
two parts of the speaker meet. Another installation method is to place the speaker on the surface and use ground cover
materials to “berm up” to the boundary between the two sections, being careful not to cover the ared waveguide in the upper
half of the speaker, or the speaker can be installed on the top surface of wooden decks or cement slabs. There are three
recessed pathways on the bottom of the speaker to allow for entrance and exit when using mutiple speakers on distributed
lines.
Anchoring the speaker for stability and security can be accomplished using after-market stakes placed through one, two or all
three pre-drilled holes located at the base of each of the legs on the bottom section.
The second gland nut can be installed by drilling a 22 mm
(7/8 in, 0.875 in) hole on the side of the bottom half of the
enclosure, in one of three recesses on the underside of the
enclosure, or other locations as needed, while taking care
that the location chosen does not interfere with the
locking parts so both halfs of the enclosure will mate and
close properly.
Attach one of the two included Gland Nuts into the open
hole on the seal plate as shown above.
Install the gland nut into the hole as shown
above in #6 and feed external wire from
outside through the gland nut and up through
the center hole in the lower half of the speaker
as shown above.
3
4
5
Close-up view of tap setting for the Control 85M and
Control 88M. **Adjusting tap setting required before
powering up system.
88M
85M
6
Continue to extend external wire up through the gland
nut installed on the seal plate and attach to pre-existing
wires from the top section of the speaker with included
gel-lled wire nuts.
7
** To achieve a watertight
seal with these gland nuts,
use only round jacketed
cable with outside diameter
(O.D.) between 4.0mm (0.16”)
and 9.0 mm (0.36”).
IMPORTANT: WIRE SIZE
When all wires are set into place as shown in #9, tighten
down both gland nuts by rotating the larger side until
the gland material clamps down on the wire creating a
water tight seal.
Line up the upper section pins and lower section
grooves.
Begin to re-assemble speaker by taking care to place wire nut
connectors in top section of speaker and reattach the seal
plate with screws as shown above.
Rotate top section counter-clockwise to lock the
top to the bottom section, being careful to line up
the security screw hole with brass nut on the
bottom half of the speaker.
Using included security screwdriver, and making sure you
have lined up the security screw with brass nut, turn clock-
wise so screw will lock top and bottom section together.
89
10 11
12 13
Replace cap covering set screw.


Produktspezifikationen

Marke: JBL
Kategorie: Lautsprecher
Modell: Control 85M

Brauchst du Hilfe?

Wenn Sie Hilfe mit JBL Control 85M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Lautsprecher JBL

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung fĂĽr -Kategorien-