Janome Quilt Maker 18 Bedienungsanleitung
Janome
Nähmaschine
Quilt Maker 18
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Janome Quilt Maker 18 (25 Seiten) in der Kategorie Nähmaschine. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/25
QF01510 8-foot Longarm Quilng Frame
(with oponal 2-foot extension)
Assembly Instrucons
January, 2021
Table of Contents
2...........Parts List
3...........Secon 1: Table Top Frame
4...........Secon 2: Leg Assemblies
5...........Secon 3: Legs to Table Top
6...........Secon 4: Corner Braces
7...........Secon 5: Track Supports
8...........Secon 6: Aligning Track
9...........Secon 7: Horizontal Braces, Right & Le
10.........Secon 8: Narrow Vercal Braces
11-12 ...Secon 9: Wide Vercal Braces, Right & Le
13.........Secon 10: Cross Brace
14.........Secon 11: Pole Supports, Ratchet-Stop End
15.........Secon 12: Pole Supports, No Ratchet-Stop End
16.........Secon 13: Ratchet Stops, Shown on Right End
17.........Secon 14: Pole Pre-assembly
18.........Secon 15: Pole Assemblies
19.........Secon 16: Pole Assemblies, 10-Foot
20.........Secon 17: Poles on Frame
21.........Secon 18: Leveling Frame
22.........Secon 19: Velcro and Leaders
23.........Secon 20: Bungee Side Clamps
24.........Secon 21: Loading the Quilt
25.........Secon 22: Changing the Pole Posion Seng
8-foot Longarm Frame Assembly InstruconsPage 2
PART # DESCRIPTION QTY
QF01500-243 LEG CAP, PLASTIC 2
QF09318-178 LEVELER FOOT 2
QF01500-241 LOWER LEG 1
QF01500-242 UPPER LEG 2
QF09318-07 SCREW-M8 X 16 SKB ZN 2
QF05300-157 WASHER-M8 NYLON 2
QF01500-170 CROSS BAR, 1
QF01500-200 BRACE, CORNER 4
QF01500-211 RAIL, 24” 2
QM13274 WASHER-M4 FLAT ZN 16
QM13237 SCREW-M4 X 12 BUTTON HEAD 24
QF01500-270 SCREW-M4 X 10 FLAT HEAD 4
QF01500-230 TRACK SUPPORT 24” 2
QF01500-300-30 POLE COUPLER 4
QF01500-300-10 POLE SECTION, SHORT (2’) 4
QF09318-714 SNAP BUTTON 4
QF01500-251 TRACK INSERT, 10’ 2
PART # DESCRIPTION QTY
QF01510-100 VERTICAL BRACE, NARROW 2
QF01510-110 VERTICAL BRACE, WIDE (RIGHT) 1
QF01510-120 VERTICAL BRACE, WIDE (LEFT) 1
QF01510-130 BRACE, CROSS 2
QF01510-150 HORIZONTAL BRACE ( ) 1RIGHT
QF01510-160 HORIZONTAL BRACE (LEFT) 1
QF01500-170* CROSS BAR 6
QF01500-180 RATCHET STOP 3
QF01500-190 POLE SUPPORT, PLASTIC 8
QF01500-200 BRACE, CORNER 8
QF01500-210* RAIL, 48” 4
QF01500-220* TRACK SUPPORT, 36” 4
QF01500-230* TRACK SUPPORT, 24” 2
QF01500-243 LEG CAP, PLASTIC 6
QF09318-178 LEVELER FOOT 6
QF01500-241 LOWER LEG 3
QF01500-242 UPPER LEG 6
QF09318-07 SCREW-M8 X 16 SKB ZN 6
QF05300-157 WASHER-M8 NYLON 6
QF01500-260 SCREW-M6 X 14 SHOULDER ZN 3
QF01500-270 SCREW-M4 X 10 FLAT HEAD 44
QF01500-300-20* POLE SECTION, LONG (4’) 8
QF09318-714 SNAP BUTTON 8
QF01500-800 RATCHET WHEEL 3
QF01500-300-30 POLE COUPLER 4
QM13237 SCREW-M4 X 12 BUTTON HEAD 116
QM13274 WASHER-M4 FLAT ZN 81
QF00035 BUNGEE SIDE CLAMP 2
QF00035-1 CORD LOCK 2
QF01500-250 TRACK INSERT, 8 FT 2
QF09318-113 5MM HEX KEY HANDLE 1
QF09318-111 3MM HEX KEY HANDLE 1
QF09318-116 2.5MM HEX DRIVER TOOL 1
QF01503 7.5’ LEADER SET 1
QF10619 VELCRO 3/4 HOOK WHITE ADHSV 1
Parts Lists
Parts List 8-foot Longarm Quilng Frame Parts List 2-foot Extension (oponal)
BOX 1: Includes everything without an asterisk
*BOX 2: Includes items with an asterisk
Page 3
8-foot Longarm Frame Assembly Instrucons
Tools Needed: 2.5mm hex tool ( ) and provided
measuring tape ( )not provided .
1. Lay the parts out as shown. Assemble the table
frame using two screws down through the rail
at each end into the threaded inserts in the
cross bars.
NOTE: Start all the screws at both ends
of the three cross bars before ghtening
them with the provided 2.5mm hex tool.
2. Repeat this process for the other two cross
bars.
3. Tighten the screws rmly with the 2.5mm
hex tool.
4. Repeat Steps 1 through 3 for a second table
top frame.
Â10" NOTE: If you are using the oponal
2-foot extension repeat Steps 1 through
3 for the one cross bar on the short table
top frame.
5. Flip the table top frames upside down and
align them together.
ÂIMPORTANT: Using a measuring tape
measure diagonally from one outside
corner to the other outside corner. The
measurement should be very close
to 53". Repeat the process diagonally
across the other two corners. The two
measurements should be the same to
ensure the top is squared. Secons will
be joined with table legs.
3
2
1
Secon 1: Table Top Frame
ITEM PART # DESCRIPTION QTY
1 QF-01500-270 SCREW-M4 X 10 FLAT HEAD 24
2 QF01500-210 48” RAIL, 4
3 QF01500-170 CROSS BAR 6
NOTE: If you are using the oponal
2-foot extension, place it in the
center between the two 4-secons
8-foot table frame shown together
without oponal 2-foot extension
10-foot table frame shown together with
oponal 2-foot extension in the center
Produktspezifikationen
| Marke: | Janome |
| Kategorie: | Nähmaschine |
| Modell: | Quilt Maker 18 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Janome Quilt Maker 18 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nähmaschine Janome
18 September 2024
16 September 2024
31 August 2024
25 August 2024
18 August 2024
13 August 2024
13 August 2024
12 August 2024
12 August 2024
11 August 2024
Bedienungsanleitung Nähmaschine
- Nähmaschine Juki
- Nähmaschine Sinbo
- Nähmaschine Emerio
- Nähmaschine Tristar
- Nähmaschine Medion
- Nähmaschine SilverCrest
- Nähmaschine Bestron
- Nähmaschine Guzzanti
- Nähmaschine AEG
- Nähmaschine Alfa
- Nähmaschine Ambiano
- Nähmaschine Siemens
- Nähmaschine Jata
- Nähmaschine Lervia
- Nähmaschine IKEA
- Nähmaschine Durabase
- Nähmaschine Blaupunkt
- Nähmaschine Hema
- Nähmaschine Home Electric
- Nähmaschine Micromaxx
- Nähmaschine Mio Star
- Nähmaschine Solac
- Nähmaschine Privileg
- Nähmaschine Livoo
- Nähmaschine Easy Home
- Nähmaschine Prixton
- Nähmaschine Lifetec
- Nähmaschine Singer
- Nähmaschine Husqvarna
- Nähmaschine Termozeta
- Nähmaschine Crofton
- Nähmaschine Brother
- Nähmaschine Kohler
- Nähmaschine Primera
- Nähmaschine Veritas
- Nähmaschine Toyota
- Nähmaschine Victoria
- Nähmaschine Kayser
- Nähmaschine Jocca
- Nähmaschine Aigger
- Nähmaschine EasyMaxx
- Nähmaschine Bernina
- Nähmaschine Elna
- Nähmaschine Necchi
- Nähmaschine Pfaff
- Nähmaschine Dürkopp Adler
- Nähmaschine W6
- Nähmaschine E&R
- Nähmaschine Carina
- Nähmaschine Empisal
- Nähmaschine ER
- Nähmaschine Feiyue
- Nähmaschine Gritzner
- Nähmaschine Hofmann
- Nähmaschine Huskystar
- Nähmaschine Husqvarna-Viking
- Nähmaschine Kenmore
- Nähmaschine Lewenstein
- Nähmaschine Mediashop
- Nähmaschine Muller
- Nähmaschine Novamatic
- Nähmaschine Siemssen
- Nähmaschine Silver
- Nähmaschine Sinojo
- Nähmaschine Tesco
- Nähmaschine Vendomatic
- Nähmaschine Weasy
- Nähmaschine Yamata
- Nähmaschine Zippy
- Nähmaschine Union Special
- Nähmaschine Kunft
- Nähmaschine Meister Craft
- Nähmaschine RCE
- Nähmaschine Yamato
- Nähmaschine Baby Lock
- Nähmaschine Łucznik
- Nähmaschine Anker-Bernette
- Nähmaschine LERAN
- Nähmaschine Prince
- Nähmaschine Bernette
- Nähmaschine Sewmaq
- Nähmaschine SteamMax
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024