Indian Chief Vintage (2015) Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Indian Chief Vintage (2015) (185 Seiten) in der Kategorie Motor. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/185
Indi Chief ®Claic
Indi Chief ® Vintage
Indi Chieftain ®
Indi Roadmaster™
2015
RIDER’S
MANUAL
California Proposition 65 Warning
This product contains or emits
chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
1
2015 Rider’s Manual
Indian Chief ® Classic
Indian Chief ® Vintage
Indian Chieftain®
Indian Roadmaster™
2
Copyright 2014 Indian Motorcycle International, LLC
All information contained within this publication is based on the latest product information available at the time of publication. Product
improvements or other changes may result in differences between this manual and the motorcycle. Depictions and/or procedures in this
publication are intended for reference use only.
No liability can be accepted for omissions or inaccuracies. Indian Motorcycle Company reserves the right to make changes at any time,
without notice and without incurring obligation to make the same or similar changes to motorcycles previously built. Any reprinting or
reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited.
INDIAN®, INDIAN MOTORCYCLE®, CHIEF®, CHIEFTAIN® and ROADMASTER™ are trademarks of Indian Motorcycle Company.
iPhone®, iPod®, iPod nano®, and iPod touch® are trademarks of Apple Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by INDIAN
MOTORCYCLE is under license. Other trademarks and trade names are those of their respective owners.
Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc. Used with
permission.
Garmin® and zumo® are registered trademarks of Garmin Ltd. or its subsidiaries.
JCASE® is a registered trademark of Littelfuse, Inc.
Printed in U.S.A.
P/N 9925951
3
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Reporting Safety Defects . . . . . . . . . . . . 19
Component Identification . . . . . . . . . . . .21
Instruments, Features & Controls. . . . . . .24
Pre-Ride Inspections. . . . . . . . . . . . . . . . .62
Operation . . . . . . . . . . . . . . . . . . . . . . . . .72
Maintenance . . . . . . . . . . . . . . . . . . . . . . .84
Cleaning and Storage. . . . . . . . . . . . . . .128
Specifications . . . . . . . . . . . . . . . . . . . . .133
Warranty . . . . . . . . . . . . . . . . . . . . . . . . .138
Maintenance Log. . . . . . . . . . . . . . . . . . .149
Audio System (if equipped). . . . . . . . . .151
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
5
Introduction
Identification Number Records
Record important identification numbers below.
Vehicle Identification Number (VIN) (see page 20)
Engine Identification Number (see page 6)
Master PIN
Rider PIN
Key Fob #1 Serial Number
Key Fob #2 Serial Number
Key Fob #3 Serial Number
Key Fob #4 Serial Number
6
Introduction
Service and Warranty Information
Some procedures are beyond the scope of this manual. See your dealer to purchase an INDIAN MOTORCYCLE Service Manual.
Some procedures provided in the service manual require specialized knowledge, equipment, and training. Be sure you have
the required technical skills and tools that are needed before you attempt ANY service on your motorcycle. Please contact
your authorized dealer before attempting any service work that is beyond your level of technical knowledge or experience,
or if the work requires specialized equipment.
Operating Your Motorcycle Outside the U.S.A.
If you plan to operate your motorcycle in countries other than the USA and Canada:
• Service facilities or replacement parts may not be readily available.
• Unleaded gasoline may not be available. The use of leaded fuels will cause engine damage, damage to your emissions
systems and voiding of your warranty.
• Gasoline may have a considerably lower octane rating. Improper fuel can cause engine damage.
Engine Identification Number
The engine number is stamped into the right crankcase beneath the
balance shaft cover. The engine number is positioned behind the
right floorboard with the engine installed in the frame. Record the
number in the space provided on page 5.
Engine Identification Number
8
Safety
Safe Riding Practices
Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and
understand the information contained in this section before operating the motorcycle. This section contains safety information specific to the
INDIAN motorcycle, as well as information about general motorcycle safety. Anyone who rides the motorcycle (operators and passengers) must
follow these safety precautions.
Motorcycling has inherent risks.
You can minimize those risks, but you can't eliminate them
completely. Even if you're an experienced motorcycle
operator or passenger, read all of the safety information in
this manual before operating the motorcycle.
• Take a rider education course from the Motorcycle Safety
Foundation or another qualified instructor. The course will
help you develop or refresh your expertise in safe riding
habits through instruction and riding. For information on
Motorcycle Safety Foundation rider education courses in
your area, call 1-800-446-9227 or visit www.msf-usa.org.
• Read and understand all information in this rider’s
manual.
• Observe all maintenance requirements specified in this
manual. See the INDIAN MOTORCYCLE Service Manual or
an authorized INDIAN MOTORCYCLE dealer.
Design characteristics affect how you should ride
the motorcycle:
• The motorcycle is designed for on-road use with one
rider and one passenger. Never exceed the GVWR or the
GAWR. Refer to the Specifications section of this manual
(page 133) or the Manufacturing Information/VIN label on
the motorcycle frame for model-specific information.
• Riding off-road, riding with more than one passenger, or
carrying weight exceeding the maximum weight rating
can make handling difficult, which could cause loss of
control.
• During the first 500 miles (800 km) of operation, follow all
break-in procedures as outlined in the break-in section
beginning on page 72. Failure to do so can result in
serious engine damage.
• Some models include saddlebags, a windshield, a trunk,
lower fairings or a passenger backrest as standard
equipment. To maintain stability, be prepared to reduce
the operating speed of motorcycles equipped with these
items.
WARNING
9
Safety
Safe Riding Practices
Follow these general safe riding practices:
• Before each ride, perform the pre-ride inspections as
outlined beginning on page 62. Failure to do so may result
in damage to the motorcycle or an accident.
• Until you're thoroughly familiar with the motorcycle and
all of its controls, practice riding where there is little or no
traffic. Practice riding at a moderate speed on various
road surfaces and in different weather conditions.
• Know your skills and limits, and ride within them.
• Allow only licensed, experienced operators to ride your
motorcycle, and then only after they have become
familiar with its controls and operation. Make sure all
riders read and understand this rider’s manual before
riding.
• Do not ride when you're fatigued, ill or under the
influence of alcohol, prescription drugs, over-the-counter
drugs or any other drugs. Fatigue, illness, alcohol and
drugs can cause drowsiness, loss of coordination and loss
of balance. They can also affect your awareness and
judgment.
• If your motorcycle operates abnormally, correct the
problem immediately. See the INDIAN MOTORCYCLE
Service Manual or an authorized INDIAN MOTORCYCLE
dealer.
• Ride defensively, as if you are invisible to other motorists,
even in broad daylight. A motorist's failure to see or
recognize a motorcycle is the leading cause of automobile/
motorcycle accidents. Ride where you're clearly visible to
other motorists, and observe their behavior carefully.
• Be especially cautious at intersections, as these are the
most likely places for an accident.
• To prevent loss of control, keep your hands on the
handlebars and your feet on the footrests.
• Be aware that a highway bar is not designed to protect the
rider from injury in a collision.
• Obey the speed limit and adjust your speed and riding
technique based on road, weather and traffic conditions.
As you travel faster, the influence of all other conditions
increases, which can affect the motorcycle's stability and
increase the possibility of losing control.
10
Safety
Safe Riding Practices
• Reduce speed when:
- The road has potholes or is otherwise rough or uneven.
- The road contains sand, dirt, gravel or other loose sub-
stances.
- The road is wet, icy or oily.
- The road contains painted surfaces, manhole covers, metal
grating, railway crossings or other slippery surfaces.
- The weather is windy, rainy or otherwise causing slippery or
rapidly changing conditions.
- Traffic is heavy, congested, not allowing sufficient space
between vehicles or otherwise not flowing smoothly.
- You are being passed in either direction by a large vehicle
that may produce a wind blast in its wake.
• When approaching a curve, choose a speed and lean
angle that allows you to pass through the curve in your
own lane without applying the brakes. Excessive speed,
improper lean angle or braking in a curve can cause loss
of control.
• Ground clearance is reduced when the motorcycle leans.
Do not allow components to contact the road surface when
leaning the motorcycle in a curve, as this could cause loss
of control.
• Do not tow a trailer. Towing a trailer can make the
motorcycle hard to handle.
• Retract the sidestand fully before riding. If the sidestand
is not fully retracted, it could contact the road surface and
cause loss of control.
• To maximize braking effectiveness, use the front and rear
brakes together. Be aware of the following braking facts
and practices:
- The rear brake provides 40% of the motorcycle's stopping
power, at most. Use the front and rear brakes together.
- To avoid skidding, apply the brakes gradually when the road
is wet or rough, or contains loose or other slippery
substances.
- If possible, avoid applying the brakes while making a turn.
Motorcycle tires have less traction during turns, so braking
will increase the possibility of skidding. Bring the motorcycle
to the upright position before applying the brakes.
- With new pads and rotors, allow up to 250 miles (500 km) of
operation in urban driving conditions (not highway cruising)
to allow pads to mate with new rotors. Brakes should be used
frequently. During this time brake performance will be less
effective. Avoid using brakes harshly unless in an emergency.
Brake efficiency will gradually increase during this seating
period.
Anti-Lock Brake System Response
• When the anti-lock brakes engage during a braking
event, the rider will feel pulsing at the brake levers.
Continue to apply steady pressure to the brakes for the best
stopping performance.
11
Safety
Safe Riding Practices
Carrying a Passenger
Do not carry a passenger unless the motorcycle is equipped with passenger seat and passenger footrests.
To carry a passenger safely:
• Do not exceed the gross vehicle weight rating (GVWR) for
your motorcycle. Refer to the Specifications section of this
manual (page 133) or the Manufacturing Information/VIN
label on the motorcycle frame for model-specific
information.
• Adjust ride height as needed. See pages 95-97.
• Direct the passenger to hold onto you or to the passenger
hand strap with both hands and to keep both feet on the
passenger footrests. Do not carry a passenger who cannot
place both feet firmly on the passenger footrests. A
passenger who is not holding on properly, or who cannot
reach the passenger footrests, can shift their body
erratically, which can make the motorcycle hard to handle
and cause loss of control.
• Before riding, be sure your passenger knows safe riding
procedures. Discuss any safety information unfamiliar to
your passenger. A passenger who is unaware of safe
riding procedures may distract you or make movements
that make the motorcycle hard to handle.
• Adjust your riding style to compensate for the differences
in handling, acceleration and braking caused by the
additional weight of the passenger. Failure to do so can
cause loss of control.
12
Safety
Safe Riding Practices
Protective Apparel
Wear protective apparel to decrease the risk of injury and increase riding comfort.
• Always wear a helmet that meets or exceeds established
safety standards. Approved helmets in the USA and
Canada bear a U.S. Department of Transportation (DOT)
label. Laws in some areas require that you wear an
approved helmet. Head injuries are the leading cause of
fatalities in accidents involving motorcycles. Statistics
prove that an approved helmet is the most effective
protection in preventing or reducing head injuries.
• Wear eye protection to protect eyes from wind or airborne
particles and objects. Laws in some areas require that you
wear eye protection. We recommend that you wear
approved Personal Protective Equipment (PPE) bearing
markings such as VESC 8, V-8, Z87.1, or CE. Make sure
protective eyewear is kept clean.
• All riders should wear bright or light-colored and/or
reflective clothing to improve visibility to other motorists.
A motorist's failure to see or recognize a motorcycle is the
leading cause of automobile/motorcycle accidents.
• Wear gloves, a jacket, heavy boots and long pants to
prevent or reduce injury from abrasions, lacerations or
burns should the motorcycle fall. Wear boots with low
heels, as high heels can catch on pedals or footrests. The
combination of boots and pants should completely cover
legs, ankles and feet, protecting skin from engine and
exhaust system heat.
• Do not wear loose, flowing clothing or long boot laces, as
they can catch on handlebars, levers or footrests, or they
can become entangled in the wheels, causing loss of
control and serious injury.
13
Safety
Use of Accessories
Because INDIAN MOTORYCLE cannot test and make
specific recommendations concerning every accessory or
combination of accessories sold, the operator is responsible
for determining that the motorcycle can be safely operated
with any accessories or additional weight. Use the following
guidelines when choosing and installing accessories:
• Do not install accessories that impair operator visibility or
the stability, handling or operation of the motorcycle.
Before installing an accessory, be sure that it does not:
- reduce ground clearance when the motorcycle is either
leaned or in a vertical position;
- limit suspension or steering travel or your ability to operate
controls;
- displace you from your normal riding position;
- obscure lights or reflectors.
• Bulky, heavy or large accessories can cause instability
(due to the lifting or buffeting effects of wind) and loss of
control.
• Do not install electrical accessories that exceed the
capacity of the motorcycle’s electrical system. Never
install higher wattage light bulbs than those supplied as
original equipment. An electrical failure could result and
cause hazardous loss of engine power or lights, or
damage to the electrical system. See page 122.
• Use only genuine INDIAN MOTORYCLE accessories
designed for your model. See your authorized INDIAN
MOTORCYCLE dealer.
• Do not exceed the gross vehicle weight rating (GVWR) for
your motorcycle.
• Adjust ride height as needed. See pages 95-97.
14
Safety
Modifications
Modifying the motorcycle by removing any equipment or by
adding equipment not approved by the manufacturer may
void your warranty. Such modifications could make the
motorcycle unsafe to ride and could result in severe injury
to operator or passenger, as well as damage to the
motorcycle. Some modifications may not be legal in your
area of operation. If in doubt, contact your authorized
INDIAN MOTORCYCLE dealer.
Parking the Motorcycle
When leaving the motorcycle unattended, turn the engine
off. Park the motorcycle where people are not likely to touch
the hot engine or exhaust system or place combustible
materials near these hot areas. Do not park near a
flammable source such as a kerosene heater or an open
flame, where hot components could ignite combustible
materials.
Park the motorcycle on a firm, level surface. Sloped or soft
surfaces may not support the motorcycle. If you must park
on a slope or soft surface, follow the precautions outlined on
page 83.
Saddlebags, Trunk and Other Storage
Whenever operating a motorcycle equipped with cargo
storage features such as saddlebags, a trunk, racks, glove
boxes or other storage compartments:
• Never ride at excessive speeds. Storage features and
cargo, combined with the lifting or buffeting effects of
wind, can make a motorcycle unstable and cause loss of
control.
• Distribute weight evenly on each side of the motorcycle.
• Do not exceed the individual weight limit of any
saddlebag, trunk or other storage compartment. Refer to
the storage capacity label located on or near the storage
feature. See page 20.
• NEVER EXCEED the GROSS VEHICLE WEIGHT RATING
(GVWR) or the GROSS AXLE WEIGHT RATING (GAWR),
regardless of whether or not any storage feature is loaded
to capacity. Exceeding the weight rating can reduce
stability and handling and cause loss of control.
• Adjust ride height as needed. See pages 95-97.
15
Safety
Carrying Cargo
Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also
refer to the contents of any accessories.
• Keep cargo and accessory weight to a minimum, and
keep items as close to the motorcycle as possible to
minimize a change in the motorcycle’s center of gravity.
Changing the center of gravity can cause loss of stability
and handling and could cause loss of control.
• Adjust ride height as needed. See pages 95-97.
• Do not exceed the gross vehicle weight rating (GVWR) for
your motorcycle.
• Distribute weight evenly on both sides of the motorcycle.
Maintain even weight distribution by checking
accessories and cargo to make sure they’re securely
attached to the motorcycle before riding and whenever
you take a break from riding. Uneven weight distribution
or sudden shifting of accessories or cargo while you’re
riding may cause difficult handling, loss of control and
driving hazards for other motorists (if cargo falls from the
motorcycle).
• For riding comfort and to ensure proper ground
clearance, adjust rear shock air pressure as specified on
the label located under the left side cover. See page 96.
• Do not attach large or heavy cargo such as sleeping bags,
duffel bags or tents to the handlebars, front fork area or
front fender. Cargo or accessories placed in these areas
can cause instability (due to improper weight distribution
or aerodynamic changes) and could cause loss of control.
Such items can also block air flow to the engine and cause
overheating that can damage the engine.
• Do not exceed the maximum cargo weight limit of any
accessory (see accessory instructions and labels). Do not
attach cargo to an accessory not designed for that
purpose. Either circumstance could result in an accessory
failure that could cause loss of control.
• Always obey posted speed limits.
• Do not attach anything to the motorcycle unless
specifically designed for that purpose by INDIAN
MOTORYCLE.
16
Safety
Transporting the Motorcycle
If you must transport the motorcycle:
• Use a truck or trailer. Do not tow the motorcycle with
another vehicle, as towing will impair the motorcycle's
steering and handling.
• Position and restrain the motorcycle in an upright
position. If the motorcycle leans to one side, gasoline may
leak from the fuel tank and result in a fire hazard or
damage to the finish.
• Do not restrain the motorcycle using the handlebars.
• Loop tiedown straps (from the front) up and over the lower
triple clamp, using care to not interfere with wiring and
brake lines. Place tiedowns as wide apart as possible on
the truck or trailer bed for best stability.
Fuel and Exhaust Safety
Always heed these fuel safety warnings when refueling or
servicing the fuel system. For fueling procedures, see page
74.
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always turn off the engine before refueling.
• Always refuel outdoors or in a well-ventilated area.
• Open the fuel cap slowly. Do not overfill the tank. Do not fill the
tank neck.
• Do not smoke or allow open flames or sparks in or near the area
where refueling is performed or where gasoline is stored.
Gasoline and gasoline vapors are poisonous and can cause severe
injury.
• Do not swallow gasoline, inhale gasoline vapors, or spill gasoline.
If you swallow gasoline, inhale more than a few breaths of gasoline
vapor, or get gasoline in your eyes, see a physician immediately.
• If gasoline spills on your skin or clothing, immediately wash it off
with soap and water and change clothing.
Exhaust gases contain carbon monoxide, a colorless, odorless gas
that can cause loss of consciousness or death in a short time.
• Never start the engine or let it run in an enclosed area.
• Never inhale exhaust gases.
WARNING
17
Safety
Safety Maintenance
Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury
or death. Always perform the safety maintenance procedures as recommended in this manual. Perform maintenance and repairs promptly. See
the INDIAN MOTORCYCLE Service Manual or an authorized INDIAN MOTORCYCLE dealer.
• Before each ride, perform the Pre-Ride Inspections. See
page 62.
• Perform all periodic maintenance at the recommended
intervals outlined in the Periodic Maintenance section
beginning on page 86.
• Always maintain proper tire pressure, tread condition and
wheel and tire balance. Inspect tires regularly and
replace worn or damaged tires promptly. Use only
approved replacement tires. See the Specifications section
beginning on page 133.
• Always ensure proper steering head bearing adjustment.
Regularly inspect the rear shock absorber and the front
forks for fluid leaks or damage. Make any necessary
repairs promptly. See page 99.
• Clean the motorcycle thoroughly to reveal items in need
of repair.
• Fasteners must meet original specifications for quality,
finish and type to ensure safety. Use only genuine INDIAN
MOTORYCLE replacement parts, and ensure that all
fasteners are tightened to the proper torque.
WARNING
18
Safety
Electromagnetic Interference
This vehicle complies with UN ECE Regulation 10
requirements and Canadian ICES-002.
Key Fob and Vehicle Control Module
FCC/IC Compliance Statement
FCC: W99PI01, W99PI02
IC: 8296A-PI01; 8296A-PI02
This device complies with Part 15 of the FCC Rules and
Canada license-exempt RSS-210 standard. Operation is
subject to the following two conditions:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
19
Safety
Gross Vehicle Weight Rating (GVWR)
WARNING! Exceeding the gross vehicle weight rating of your
motorcycle can reduce stability and handling and could cause loss of
control. NEVER exceed the GVWR of your motorcycle.
The maximum load capacity of your motorcycle is the
maximum weight you may add to your motorcycle without
exceeding the GVWR. This capacity is determined by
calculating the difference between your motorcycle’s GVWR
and wet weight.
Refer to the Specifications section of this manual (page 133)
or the Manufacturing Information/VIN label on the
motorcycle frame for model-specific information.
When determining the weight you will be adding to your
motorcycle, and to ensure you do not exceed the maximum
load capacity, include the following:
• operator body weight
• passenger body weight
• weight of all riders’ apparel and items in or on apparel
• weight of any post-production accessories and their
contents
• weight of any additional cargo on the motorcycle
Reporting Safety Defects
If you believe that your vehicle has a defect that could result
in a crash or cause injury or death, you should immediately
inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying INDIAN MOTORYCLE in
writing.
If NHTSA receives similar complaints, it may open an
investigation, and if it finds that a safety defect exists in a
group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in
individual problems between you, your INDIAN
MOTORCYCLE dealer or Indian Motorcycle Company.
To contact NHTSA, or obtain other information about motor
vehicle safety, you may either call the Vehicle Safety Hotline
toll-free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the
NHTSA web site at www.safercar.gov, or write to:
ADMINISTRATOR, NHTSA
1200 New Jersey Avenue, SE
West Building
Washington, DC 20590
20
Safety
Safety and Information Labels
Labels are model-specific and market-specific. Your motorcycle may not contain all of the labels shown.
1. Vehicle Identification Number (VIN) (side of steering head)
2. Vehicle Emission Control Information (VECI)
3. Noise Emission Control Information (NECI)
4. Operator Warning/Fuel Recommendation
5. Saddlebag/Cargo Warning
6. Highway Bar Warning
7. Shock Air Pressure Warning (if equipped) (under side cover)
8. Rear Wheel Service Warning (if equipped) (under side cover)
9. Trunk Rack Capacity Label
10. Trunk Capacity Label
11. Lower Fairing Glove Box Cargo Capacity Labels (inside covers)
12. Rear Tip-Over Bar Warning
1
10
5
6
2,3
7,8
4
11
12
9
ROADMASTER shown
21
Component Identification
Console
1. Clutch Lever
2. Fuel Gauge (CHIEF)
3. Instrument Cluster
4. Power Switch/Security Light
5. Front Brake Master Cylinder
6. Throttle Control Grip
7. Front Brake Lever
8. 12-Volt Outlet (CHIEFTAIN/ROADMASTER)
9. Auxiliary Light Switch (CHIEFTAIN/ROADMASTER)
10. Fuel Cap
11. Ornamental Cap (Do not remove)
1
10
7
6
5
4
CHIEFTAIN/ROADMASTER (CHIEFTAIN shown)CHIEF
11
3
2
8
1
5
4
10
11
67
39
22
Component Identification
1. Rear Brake Pedal
2. Right Front Turn Signal
3. Windshield (if equipped)
4. Auxiliary Lights
5. Left Front Turn Signal
6. Headlight
7. INDIAN MOTORYCLE War Bonnet
8. Passenger’s Foot Peg/Floorboard (if equipped)
9. Driver’s Footrest
10. Gear Shifter
11. Glove Box Storage (if equipped)
12. Speakers
13. Mirror
14. 12-Volt Outlet (if equipped)
15. USB Cord
16. Taillight
17. Right Rear Turn Signal
18. Left Rear Turn Signal
19. Lower Fairing Wind Deflector (if equipped)
20. Lower Fairing Vent (if equipped)
21. Lower Fairing (if equipped)
3
6
5
8
4
2
7
10 9
1
12
16
17
18
ROADMASTER shown
15
14 13
13
CHIEFTAIN shown
11
21
20
19
11
11
23
Component Identification
22. Front Fork
23. Fuel Tank
24. Air Box Cover (left)
25. Driver’s Seat
26. Battery (under seat)
27. Passenger Seat (if equipped)
28. Saddlebag (if equipped)
29. Radio Antenna (if equipped)
30. Side Cover (Left)
31. Shock Air Fill (under cover) (CHIEFTAIN/ROADMASTER)
32. 12-Volt Outlet (saddlebag) (CHIEFTAIN/ROADMASTER)
33. Muffler
34. Sidestand
35. Trunk Cargo Rack (if equipped)
36. Trunk (if equipped)
37. Rear Tipover Bar (if equipped)
38. Front Tipover Bar (if equipped)
7
10 34
31
CHIEFTAIN shown
5
4
932
26 28
27 29
24
23
25
22
8
30
33
36
ROADMASTER shown
35
37 38
24
Instruments, Features and Controls
Switches
Flasher (Hazard)
Switch
High/Low
Light Switch
Horn
Switch
Turn Signal
Switch
Engine
Starter
Switch
Engine
Stop/Run
Switch
LEFT-TOGGLE Switch
Audio Control Switches
(if equipped)
Cruise
Control
Switch Cruise
On/Off
Switch
Left Control
Left Control
Right Control
Right Control
RIGHT-TOGGLE Switch
(active on CHIEFTAIN and ROADMASTER)
Windshield
Switches
(if equipped)
26
Instruments, Features and Controls
Switches
Symbol Switch Description
Emergency Flasher
Switch (Hazard
Switch)
The hazard switch activates and cancels the emergency flashers. See page 27.
High/Low Headlight
Beam Switch
The high/low headlight beam switch toggles the headlight between high beam and low beam. See page
29.
-- Auxiliary Light
Switch
Press the auxiliary light switch to turn the auxiliary lights off or on. See page 29.
Horn Switch Press the horn switch to sound the horn.
Turn Signal Switch Move the switch to the left to activate the left turn signals. Move the switch to the right to activate the right
turn signals. A signal will deactivate automatically when speed or distance reach predetermined levels.
To cancel a signal manually, move the switch to the center position and push it inward.
Momentary Feature: Move the turn signal switch left or right and hold it in that position for at least one second.
The momentary feature will activate and the signal will then cancel when the switch is released.
Stop/Run Switch Press the bottom of the switch (RUN) to allow the engine to start and run. Press the top of the switch (STOP)
to stop the engine. See page 27.
Starter Switch Use the starter switch to start the engine. The engine stop/run switch must be in the RUN position. See
page 28.
Power Switch The power switch is located above the instrument gauge. Press and release the power switch to enable or
disable all electrical power to the vehicle. See page 27.
-- Saddlebag/Trunk
Lock Switch
Press the lock switch to lock or unlock the saddlebags and trunk (if equipped). The key fob can also be
used to lock or unlock the saddlebags and trunk.
-- Heated Grip Switch Use the hand grip heater switch to turn the grip heaters on or off and to adjust the heat level. See page 30.
27
Instruments, Features and Controls
Switches
Power Switch
The power switch is attached to the fuel tanks on the center
console. Press and release the power switch to enable or
disable all electrical power to the vehicle. The power switch
does not have to be on to start the engine. See page 28.
To disable all electrical power if the motorcycle is moving
and the engine is running, press and hold the power switch
for more than three (3) seconds.
Tip: To save battery power, the vehicle will power off after five
minutes of inactivity.
Hazard Switch
The power switch must be ON to activate the flashers, but
once activated, the flashers will continue to flash when the
power switch is turned off. When the flashers are active, all
four turn signals flash.
• Press the switch to activate the flashers.
• Press the switch again to cancel the flashers.
Engine Stop/Run Switch
Use the engine stop/run switch
to turn the engine off quickly.
• Press the top of the switch
(STOP) to interrupt the
circuits and stop the engine.
The engine should not start or
run when the switch is in the
STOP position.
• Press the bottom of the switch
(RUN) to complete the circuits
and allow the engine to start
and run.
Tip: The headlights and any
accessories plugged into
power ports will remain on
until the power switch is turned
off.
Run
Stop
Right Control
28
Instruments, Features and Controls
Switches
Engine Starter Switch
Read the engine starting
procedures before starting the
engine. See page 75.
The power switch does not have
to be on to start the engine.
Press and hold the starter switch
to engage the one-touch starting
feature, which activates the
electrical system and starts the
engine. The engine stop/run
switch must be in the RUN
position and the transmission
must be in neutral.
Keyless Ignition
When the electrical system is activated with either the
power switch or the starter switch, the key fob must be
within range. If the key fob is not detected, the security light
and/or power switch will flash. The electrical system will
automatically shut down.
The starter motor will not engage during this time. If a key
fob is not available, your personal identification number
(PIN) can be entered using the turn signal switches to
unlock the security system. See page 122.
Audio System Switches
See page 151 for audio systems operation.
Cruise Control Switches
Refer to the Cruise Control section of this manual
(beginning on page 81) for cruise control operation.
Starter Switch
Right Control
29
Instruments, Features and Controls
Switches
Ignition/Light Switch
The headlights automatically come on when the engine is
started.
WARNING! Motorcycle riders must remain as visible as possible at
all times. To aid in this, the headlight must be on at all times. Do not
modify the ignition/light switch wiring to circumvent the automatic
headlight feature.
High/Low Headlight Beam Switch
The high/low headlight beam switch toggles the headlight
between high beam and low beam. To activate the high
beam, press the upper portion of the switch. To activate the
low beam, press the lower portion of the switch.
The headlights operate only when the engine is running.
You can use the high/low headlight beam switch to override
this function and allow the headlights to operate when the
engine is not running. Turn the power switch on, then toggle
the high/low headlight beam switch to turn the headlights
on.
Auxiliary Light Switch
The auxiliary lights provide additional lighting on each side
of the headlight. Some drivers prefer using the auxiliary
lights when operating in foggy conditions or when passing a
vehicle to help improve visibility to other motorists.
Press the auxiliary light
switch to turn the auxiliary
lights on or off. The switch
background light changes
color to indicate whether
lights are on or off.
OFF: Red Light
ON: Green Light
The auxiliary lights turn off
when the power switch is
turned off. The auxiliary
lights automatically turn on
when the engine starts if
they were on when the
engine was shut down.
The switch background light flashes if a fault exists with
either auxiliary light.
Auxiliary
Light Switch
30
Instruments, Features and Controls
Switches
Toggle Switches
All models are equipped with toggle switches on the front
side of the left and right handlebar controls. The LEFT-
TOGGLE switch is active for all models. The RIGHT-TOGGLE
switch is active only for CHIEFTAIN and ROADMASTER
models.
The power switch must be ON. Use the switches to toggle
through the modes of the multi-function display and to
change settings in the display.
Hand Grip Heater Switch (if equipped)
Press the top or bottom of the switch to turn the hand grip
heaters on. The center of the switch illuminates when
heaters are on. Press the center of the switch to turn the
heaters off.
The heaters have10 heat levels, ranging from OFF (level 0)
to highest heat (level 10). Press and release the top of the
switch to increase the heat level by one increment. Press and
release the bottom of the switch to decrease heat by one
increment.
The heaters turn off when the engine is turned off. When the
engine is restarted the heaters turn on at the previous heat
level setting.
If the center of the switch flashes, the heaters may not be
working properly. Please see your dealer.
LEFT-TOGGLE
Left Control Right Control
RIGHT-TOGGLE
(active for CHIEFTAIN and ROADMASTER)
INCREASE
OFF
DECREASE
31
Instruments, Features and Controls
Switches
Saddlebag/Trunk Lock Switch (if equipped)
Use the key fob or the lock switch
on the console to lock and unlock
the electric saddlebag and trunk
locks. When using the console
lock switch, the key fob must be
within range. If the key fob is not
detected, the security light and/
or power switch will flash. The
system will not perform the lock
or unlock command.
Seat Heater Switches
The seat heater toggle
switches are located on
the lower left edge of the
seat.
Key Fob
Lock
Unlock
Toggle
Position
Heat
Setting
Up HIGH
Down LOW
Center OFF
Passenger’s
Switch
Seat Heater Switches
Driver’s
Switch
32
Instruments, Features and Controls
Instrument Cluster (CHIEF)
The instrument cluster includes the speedometer, indicator
lamps and Multi-Function Display (MFD).
Speedometer
The speedometer displays forward vehicle speed in either
miles per hour or kilometers per hour.
Indicator Lamps
Indicator Lamps
Lamp Indicates Condition
Neutral The transmission is in neutral.
High
Beam
The headlight switch is set to high beam. This
indicator will flash if there is a problem with
the low or high beam light.
Speedometer Indicator Lamps
MFD
Lamp Indicates Condition
Turn
Signal
The turn signal indicator flashes when the left,
right, or both turn signals (hazard) are active.
If there is a problem in the signal system, the
lamps will flash at twice the normal rate.
Cruise
Control
Status
Amber Lamp: Cruise control is enabled, but
not set. When flashing, a cruise control
related fault exists. Green Lamp: Cruise
control is set to the desired speed. Read the
safety and operation procedures before using
cruise control. See page 81.
Check
Engine
If this lamp illuminates while the engine is
running, see your dealer promptly. The light
will remain on if the tilt sensor shuts down the
engine. If abnormal sensor or engine
operation is detected the light will remain on
as long as the fault condition exists. Retrieve
the error codes for diagnosis. See page 35.
Anti-Lock
Brakes
Not
Activated
The indicator remains on until the anti-lock
system activates, which occurs when vehicle
speed exceeds 6 MPH (10 km/h). When the
lamp is illuminated, the anti-lock brakes will
not activate, but the conventional brake
system will continue to operate normally.
Veh icl e
Speed
When standard mode is selected, speed
displays in miles per hour.
When metric mode is selected, speed
displays in kilometers per hour.
33
Instruments, Features and Controls
Instrument Cluster (CHIEF)
Multi-Function Display (MFD)
The power switch
must be ON to
access the MFD. Use
the mode switches to
toggle through the
modes of the multi-
function display and
to change settings in
the display.
Odometer
The odometer displays total distance traveled.
Trip Odometers
The trip odometers (Trip 1 and Trip 2) display total distance
traveled since being reset. To reset a trip odometer, toggle
to the trip odometer, then press and hold the LEFT-TOGGLE
switch until the trip odometer resets to zero.
Engine Speed
Engine speed displays in revolutions per minute (RPM).
DC Voltage
The volt meter displays battery voltage. If the engine is not
running, approximate battery voltage displays. If the engine
is running, approximate charging voltage displays.
Gear Position
Gear position displays at all times while the engine is
running, unless a fault occurs with the gear position sensor.
Temperature
The temperature area displays ambient air temperature.
Fuel Range
The fuel range displays the distance the motorcycle can
travel on the remaining fuel in the fuel tank.
Average Fuel Economy
Average Fuel Economy displays as of the last time the mode
was reset. To reset, press and hold LEFT-TOGGLE while
viewing the fuel economy display.
Heated Grips Heat Level Setting (if equipped)
The heated grips heat level displays if the heat level is
above zero.
Modes Available
Odometer Engine Speed
Trip Odometer 1 Average Fuel Economy
Trip Odometer 2 DC Voltage
Clock Ambient Air Temperature
Gear Indicator Fuel Range
LEFT-TOGGLE
Clutch Lever
34
Instruments, Features and Controls
Instrument Cluster (CHIEF)
Multi-Function Display (MFD)
Display Units (Standard/Metric)
The display can be changed to display either standard or
metric units of measurement.
1. Turn the ignition off.
2. Wait 10 seconds.
3. Press and hold the LEFT-TOGGLE switch while pressing
the power switch.
4. When the display flashes the distance setting, tap the
LEFT-TOGGLE switch to advance to the desired setting.
5. Press and hold the LEFT-TOGGLE switch to save the
setting and advance to the next display option.
6. Repeat the procedure to change remaining display
settings.
Clock
Tip: The clock must be reset any time the battery has been
disconnected or discharged.
1. Use the LEFT-TOGGLE switch to toggle to the odometer
display.
2. Press and hold the LEFT-TOGGLE switch until the hour
segment flashes. Release the switch.
3. With the segment flashing, tap the LEFT-TOGGLE switch
to advance to the desired setting.
4. Press and hold the LEFT-TOGGLE switch until the next
segment flashes. Release the switch.
5. Repeat steps 3-4 twice to set the 10-minute and 1-minute
segments. After completing the 1-minute segment, step
4 will save the new settings and exit the clock mode.
Standard
Display
Metric Display
Distance Miles Kilometers
Fuel U.S. Gallons I = Imperial
Gallons
Liter = Liters
Temperature Fahrenheit Celsius
Time 12-Hour Clock 24-Hour Clock
36
Instruments, Features and Controls
Instrument Cluster (CHIEF)
Multi-Function Display (MFD)
Low Oil Pressure Display
“LO OIL” displays under the following conditions.
Condition Indicates Action Required
Engine oil pressure
has dropped while the
engine is running.
Oil pressure is below a
safe operating pressure.
Stop the engine as soon as safely possible
and check the oil level. If the oil level is
sufficient, but “LO OIL” continues to display
after restarting the engine, stop the engine
immediately.
37
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
The instrument cluster includes the speedometer,
tachometer, fuel gauge, indicator lamps and multi-function
display (MFD).
Speedometer
The speedometer displays forward vehicle speed in either
miles per hour or kilometers per hour.
Tachometer
The tachometer displays engine speed in revolutions per
minute (RPM). A red line on the face of the gauge indicates
the maximum safe engine speed.
Excessive engine speed can cause engine damage or
failure, which could result in serious injury or death. Do not
allow engine speed to exceed the red line.
Fuel Gauge
The fuel gauge displays fuel level. For the most accurate
reading, sit on the motorcycle and bring it to the upright
position.
Speedometer
Indicator Lamps
Multi-Function Display
Tachometer
Fuel Gauge
38
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Indicator Lamps
Lamp Indicates Condition
Neutral The transmission is in neutral and the power switch is ON.
Vehicle
Speed
When standard mode is selected, speed displays in miles per hour.
When metric mode is selected, speed displays in kilometers per hour.
High Beam The headlight switch is set to high beam. This indicator will flash if there is a problem with the low or high beam
light.
Low Oil
Pressure
This lamp illuminates when oil pressure drops below a safe operating pressure while the engine is running. If
this lamp illuminates while the engine is running above idle speed, turn the engine off as soon as safely
possible and check the oil level. If the oil level is correct and the lamp remains on after the engine is restarted,
turn the engine off immediately. See your dealer.
Low Fuel This lamp illuminates when approximately one gallon (3.8 liters) of fuel remains in the fuel tank. The LCD
Display will switch into a Low Fuel Mileage Counter Mode to provide the rider with mileage tracking from the
time the indicator was activated.
Turn Signal One arrow flashes when the corresponding turn signal is activated. Both arrows flash when the hazard signal is
activated. If there is a problem in the signal system, the lamps will flash at twice the normal rate.
39
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Indicator Lamps
Lamp Indicates Condition
Low Battery
Vo lt age This lamp illuminates when battery voltage is low. Turn non-essential accessories off to conserve power. Make
sure the charging system is operating properly. See page 127. This lamp also illuminates with the security light
and/or power switch when the key fob battery is low, and with the TPMS lamp when the TPMS sensor battery is
low.
Cruise Control
Status Amber Lamp: Cruise control is enabled, but not set. When flashing, a cruise control related fault exists. Green
Lamp: Cruise control is set to the desired speed. Read the safety and operation procedures before using cruise
control. See page 81.
ABS Not
Activated The indicator remains on until the anti-lock system activates, which occurs when vehicle speed exceeds 6 MPH
(10 km/h). When the lamp is illuminated, the anti-lock brakes will not activate, but the conventional brake
system will continue to operate normally.
Check Engine This lamp illuminates briefly when the power switch is turned ON. This indicates proper function. If this lamp
illuminates while the engine is running, see an authorized dealer promptly. The light will remain on if the tilt
sensor shuts down the engine. If abnormal sensor or engine operation is detected the light will remain on as
long as the fault condition exists. Retrieve the error codes for diagnosis. See page 44.
Tire Pressure
Monitoring
System (TPMS)
The TPMS indicator illuminates if low tire pressure is detected. It will also illuminate along with the Low Battery
Voltage indicator when TPMS battery power is low, requiring service.
Security System
Locked This indicator lamp illuminates while the security system is searching for the key fob signal and when the
security system is locked. The lamp flashes if the key fob is not detected within range or if the fob is not
programmed properly. It also illuminates with the low battery voltage indicator when the key fob battery is low.
40
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Multi-Function Display (MFD)
The power switch must be on or the engine must be running
to view or change settings in the MFD. Use the LEFT-
TOGGLE and RIGHT-TOGGLE switches to toggle through
the modes of the multi-function display and to change
settings in the display. See page 30.
Infotainment Display
There are four zones in the
center display.
ZONE ONE (1) provides the
time and outside air
temperature. While the units for
time and temperature can be
changed, these items cannot be
adjusted by the rider.
ZONE TWO (2) will always
display audio system
information.
ZONES THREE (3) and FOUR (4)
will display vehicle/engine
information.
Tip: Zone three can be set to
display expanded audio
information. See page 43.
You can modify the items in zone four by changing the
settings in the SET BOTTOM SCREEN menu. See page 49.
LEFT-TOGGLE
Left Control Right Control
RIGHT-TOGGLE
(CHIEFTAIN/ROADMASTER)
(1)
(2)
(3)
(4)
41
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Zone Three Information
The following items can be displayed in Zone Three on the
infotainment display:
• Trip 1 Hours/Distance
• Trip 2 Hours/Distance
• Fuel Economy
• Front/Rear Tire Pressure
• Engine Hours/Oil Life
• Average Speed & Battery Voltage
• Expanded Radio Information
• Heated Grip Power Level (if equipped)
• Diagnostic Trouble Codes (DTCs)
Press LEFT-TOGGLE repeatedly to cycle through the Zone
Three displays.
Trip 1 Hours/Distance
Trip 1 Hours/Distance will display the
total hours and distance in miles or
kilometers.
1. Press and hold LEFT-TOGGLE to
reset Trip 1 hours and distance to
zero.
2. Press LEFT-TOGGLE to cycle to
the Trip 2 display.
Trip 2 Hours/Distance
Trip 2 Hours/Distance will display the
total hours and distance in miles or
kilometers.
1. Press and hold LEFT-TOGGLE to
reset Trip 2 hours and distance to
zero.
2. Press LEFT-TOGGLE to cycle to
Fuel Economy display.
42
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Zone Three Information
Fuel Economy
This screen will display the current
instant and average miles per gallon
(MPG) or liters per 100 kilometers.
1. Press and hold LEFT-TOGGLE to
reset the average.
2. Press LEFT-TOGGLE to cycle to
the Front/Rear Tire Pressure
display.
Front/Rear Tire Pressure
This screen will display the current
front and rear tire pressure in PSI or
kPa.
• Press LEFT-TOGGLE to cycle to the
Engine Hours/Oil Life display.
Engine Hours/Oil Life
This screen will display the total
engine hours accumulated when the
engine is running.
Engine oil life is also displayed. The
rate at which oil life is reduced to 0% is
determined by the following:
• Engine break-in period: 0-500 miles or
804 km
• Routine oil change intervals: Every 5,000
miles or 8,046 km
Tip: When engine oil life reaches 0%,
change the engine oil and filter.
After changing the engine oil and
filter:
1. Press and hold LEFT-TOGGLE until the value begins to
flash.
2. Press and hold LEFT-TOGGLE to reset the engine oil life
to 100%.
3. Press LEFT-TOGGLE to display Average Speed/Battery
Voltage screen.
43
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Zone Three Information
Average Speed/Battery Voltage
This screen displays the average
motorcycle speed and current battery
voltage.
1. Press and hold LEFT-TOGGLE to
reset the average speed.
2. Press LEFT-TOGGLE to cycle to
Expanded Audio Information.
Expanded Audio Information
In this mode, the display screen will
dedicate zone three to the audio
system and allow for up to six lines of
audio system information.
Press LEFT-TOGGLE to cycle to:
• Heated Grips (if equipped)
• Diagnostic Trouble Codes (if present)
• Trip 1 (top of menu)
Heated Grips (if equipped)
This screen displays the heated grip
heat level setting. The screen does not
display if heaters are set at zero or if
heated grips are not installed.
Press LEFT-TOGGLE to cycle to:
• Diagnostic Trouble Codes (if present)
• Trip 1 (top of menu)
44
Instruments, Features and Controls
Instrument (CHIEFTAIN/ROADMASTER)
Zone Three Information
Diagnostic Trouble Codes (DTCs)
If the CHECK ENGINE indicator is
illuminated on the instrument cluster,
this screen will display, indicating
there are Diagnostic Trouble Codes
(DTCs).
The error screen displays only when
the CHECK ENGINE light is on and
only during the current ignition cycle.
DTCs will reappear only if the fault
reoccurs after restarting the engine.
Retrieving Error Codes
If the CHECK ENGINE indicator illuminates, you can retrieve
the error codes from the DTC display.
1. Press and hold LEFT-TOGGLE to
enter the display screen.
Tip: The CHECK ENGINE icon will appear
on the screen when in the DTC display
mode.
2. Press LEFT-TOGGLE to cycle
through the list of available codes.
3. Record the SPN and FMI numbers.
4. See an authorized INDIAN
MOTORCYCLE dealer for code
details and diagnosis.
5. Press and hold LEFT-TOGGLE to
exit.
45
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
The instrument cluster setup menus allow the following
actions:
• Set clock
• Set units (volume, temperature, clock
type, pressure)
• Set bottom screen display (trip 1
distance, instant fuel economy,
average fuel economy, and range)
• View instrument cluster software/
hardware information
• Set Tire Pressure Monitoring System
(TPMS) (dealer only)
• Adjust infotainment display
brightness
To access the instrument cluster setup menus:
1. Place the transmission in neutral.
2. Press and hold LEFT-TOGGLE and RIGHT-TOGGLE
simultaneously until the SETUP menu appears on the
display.
3. Press RIGHT-TOGGLE repeatedly to cycle through the
setup menu.
4. Press LEFT-TOGGLE to enter the desired menu.
Setting the Clock
1. With SET CLOCK highlighted on
the setup menu, press LEFT-
TOGGLE.
2. Press LEFT-TOGGLE repeatedly
to set the hours.
3. Press RIGHT-TOGGLE to move to
tens of minutes.
4. Press LEFT-TOGGLE repeatedly
to set the tens of minutes.
5. Press RIGHT-TOGGLE to move to
minutes.
6. Press LEFT-TOGGLE repeatedly
to set the minutes.
7. Press RIGHT-TOGGLE to enter the time and move to
EXIT.
8. Press LEFT-TOGGLE to exit.
46
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Set Units
Use the SET UNITS menu to set the
following items:
• DISTANCE: Miles or kilometers
• VOLUME: Gallon, Imperial Gallon or
Liter
• TEMPERATURE: Fahrenheit or Celsius
• CLOCK TYPE: 12-hour or 24-hour
• PRESSURE: PSI or kPa
1. With SET UNITS highlighted on
the setup menu, press LEFT-
TOGGLE.
2. Press RIGHT-TOGGLE
repeatedly to cycle through
menu items.
3. Press LEFT-TOGGLE to enter
the desired SET UNITS menu.
Set Units - Distance Setting
Use the DISTANCE menu to change
the speedometer and distance
units. Select either miles or
kilometers.
1. With DISTANCE highlighted in
the SET UNITS menu, press
LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
miles or kilometers.
3. Press LEFT-TOGGLE to set the
desired setting.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
47
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Set Units - Volume Settings
Use the VOLUME menu to change
the instrument cluster volume
units. Select gallon, imperial gallon
or liter.
1. With VOLUME highlighted in
the SET UNITS menu, press
LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
gallon, imperial gallon, or liter.
3. Press LEFT-TOGGLE to set the
desired setting.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
Set Units - Temperature Settings
Use the TEMPERATURE menu to
change the instrument cluster
temperature units. Select
Fahrenheit or Celsius.
1. With TEMPERATURE
highlighted in the SET UNITS
menu, press LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
fahrenheit or Celsius.
3. Press LEFT-TOGGLE to set the
desired setting.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
48
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Set Units - Clock Type
Use the CLOCK TYPE menu to
change the clock format. Select 12-
hour or 24-hour format.
1. With CLOCK TYPE highlighted
in the SET UNITS menu, press
LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
12 hour or 24 hour.
3. Press LEFT-TOGGLE to set the
desired clock format.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
Set Units - Pressure
Use the PRESSURE menu to change
the pressure display format. Select
PSI or KPA.
1. With PRESSURE highlighted in
the SET UNITS menu, press
LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
PSI or KPA.
3. Press LEFT-TOGGLE to set the
desired pressure display
format.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
49
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Set Bottom Screen Menu
Use the SET BOTTOM SCREEN
menu to display one of the
following items in ZONE FOUR of
the display screen:
• Trip 1 Distance
• Instant Fuel
• Average Fuel
• Range
1. With SET BOTTOM SCREEN
highlighted on the setup menu,
press LEFT-TOGGLE.
2. Press RIGHT-TOGGLE
repeatedly to cycle through
menu items.
3. Press LEFT-TOGGLE to enter
the desired SET UNITS menu.
4. Press RIGHT-TOGGLE to select
EXIT.
5. Press LEFT-TOGGLE to exit.
Trip 1 Distance Display
Instant Fuel Display
Average Fuel Display
Range Display
50
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Gauge Information
The instrument cluster hardware
and software part and serial
numbers are displayed on the
Gauge Information menu.
1. With GAUGE INFORMATION
highlighted on the setup menu,
press LEFT-TOGGLE.
2. Press RIGHT-TOGGLE to select
EXIT.
3. Press LEFT-TOGGLE to exit.
Tire Pressure Monitoring System
(TPMS) Setup
Do not attempt to access the TPMS
menu. Without the proper training
and tools, you may inadvertently
erase the sensor identification
numbers from system memory,
which would disable the TPMS.
The TPMS setup menu allows your
authorized INDIAN MOTORCYCLE
dealer to register new tire pressure
sensors and to relearn erased
sensors using the TPMS tool.
LEARN TPMS
SENSORS
EXIT
TPMS
ERASE TPMS
SENSORS
51
Instruments, Features and Controls
Instrument Cluster (CHIEFTAIN/ROADMASTER)
Instrument Cluster Setup
Set Brightness
The brightness level of the instrument cluster and display
screen can be adjusted. There are two methods to enter the
Set Brightness menu.
METHOD 1:
This method bypasses the
instrument cluster setup menu. The
transmission does not have to be in
neutral using this method.
1. Press and hold RIGHT-
TOGGLE until the SET
BRIGHTNESS menu appears.
2. Press RIGHT-TOGGLE
repeatedly to adjust the
instrument cluster brightness.
3. The menu will close after the
desired brightness level is set.
METHOD 2:
1. With SET BRIGHTNESS
highlighted on the setup menu,
press LEFT-TOGGLE.
2. Press LEFT-TOGGLE
repeatedly to adjust the
brightness level from 0% to
100%.
3. When the desired brightness
level is set, press RIGHT-
TOGGLE to select EXIT.
4. Press LEFT-TOGGLE to exit.
53
Instruments, Features and Controls
Gear Shift Lever
The gear shift lever is located on the left side of the
motorcycle. Operate the lever with your foot.
• Press downward on the toe lever to shift to a lower gear.
• Lift upward on the toe lever to shift to a higher gear.
• Release the lever after each gear shift.
• See pages 77-79 for gear shifting procedures.
Tire Pressure Monitoring System
(TPMS) (if equipped)
NOTICE: On models equipped with a TPMS, the sensors are located
180° from the valve stem. Use caution when servicing tires.
To avoid damaging a sensor, break the bead at the valve
stem, then at 90° and 270° from the valve stem as required.
With a TPMS, the pressure of each tire can be viewed in the
MFD. If dashes display instead of a pressure value while
traveling above 15 MPH (24 km/h), the system may not be
functioning properly. See your dealer for service.
The TPMS warning indicator will illuminate if low tire
pressure is detected. Always correct low tire pressure
promptly. Always inspect tire pressure and condition before
each ride. See page 66.
The TPMS display may indicate an increase in tire pressure
while riding, a normal occurrence as tires warm up. Riding
into colder conditions may result in a drop in tire pressure as
tires cool down. Regardless of conditions, low tire pressures
should always be corrected promptly.
1
3
2
456
N
54
Instruments, Features and Controls
Trunk (if equipped)
Do not exceed the cargo capacity of a trunk, a cargo rack or
a trunk/cargo rack combination. The capacity for the trunk
alone, as well as for any trunk/cargo rack combination, is 30
lbs. (10 kg). The capacity for a rack alone is 5 lbs. (2.2 kg). If
you load a rack with 5 lbs. (2.2 kg) of cargo, do not add more
than 25 lbs. (11.3 kg) to the trunk.
Trunk Removal/Installation
1. Working from below
the trunk, reach up
onto the shelf to access
the harness plug. Slide
the plug upward and
forward to remove it
from the shelf.
2. Depress the release
tab to disconnect the
plug.
3. Place a shop towel on
the fender to prevent
scratches, then remove
the harness from the
plastic harness
support and place the
harness on the towel.
4. Open the saddlebag lids.
5. Make sure the anti-theft
latches are in the up
(released) position.
Tip: Locking bolts (if installed)
must be removed to access
the latches. This would also
require removing
saddlebags.
6. From the rear of the motorcycle, grasp the trunk bumper
firmly with both hands. Pull the trunk assembly upward
to disengage the trunk support legs from the saddlebag
support bracket bushings. Pull upward and rearward to
remove the trunk from the bike.
7. Place the trunk in a safe location to prevent damage.
8. Loop the harness and place
the wires into the fabric
pocket under the rear seat
flap. Place the connector in
the connector storage area
under the rear seat flap.
Lower the flap.
Step 1
Shelf
Plug
Step 3
Step 5
Harness Storage
55
Instruments, Features and Controls
Saddlebags
Do not exceed the weight limit of each saddlebag. Always
distribute weight evenly in each of the saddlebags. Hard
bag capacity is 22 lbs. (10 kg) of cargo per side. Soft bag
capacity is 15 lbs. (6.8 kg) of cargo per side.
Hard Bag Removal
1. Unlock the electric saddlebag
locks (if equipped).
Tip: The provided key can also be
used in the latch release buttons
to unlock the saddlebag lids.
2. Remove the side cover.
3. Disconnect the saddlebag
lock wiring near the seat.
4. Press the lid latch release
button and lift the lid.
5. Flip the two quick-release
latches upward.
6. Tilt the saddlebag away from the frame of the vehicle to
remove it.
7. To reinstall, place the hard bag in a fully seated position
on the muffler.
NOTICE: To prevent damage to components, always make sure
saddlebags are fully seated onto the muffler before
engaging the latches.
8. Make sure the rubber bushings on the latch pins are
fully engaged in the spools. Engage the quick-release
latches and flip them fully downward.
9. Reconnect the electrical wiring.
10. Reinstall the side cover, using care to avoid damaging
electrical wires.
Electrical Connection
Quick-Release Latch
Bushing Latch Pin
Spool
Produktspezifikationen
| Marke: | Indian |
| Kategorie: | Motor |
| Modell: | Chief Vintage (2015) |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Indian Chief Vintage (2015) benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Motor Indian
4 September 2024
28 August 2024
28 August 2024
28 August 2024
21 August 2024
19 August 2024
19 August 2024
Indian Challenger Dark Horse Icon (2022) Bedienungsanleitung
19 August 2024
18 August 2024
18 August 2024
Bedienungsanleitung Motor
- Motor Juki
- Motor Yamaha
- Motor Mitsubishi
- Motor Metabo
- Motor Mercedes-Benz
- Motor Beta
- Motor Husqvarna
- Motor Kettler
- Motor BMW
- Motor Honda
- Motor Aprilia
- Motor Ducati
- Motor Bodycraft
- Motor Reebok
- Motor KTM
- Motor Milwaukee
- Motor Benelli
- Motor Suzuki
- Motor Triumph
- Motor GasGas
- Motor Hero
- Motor Kawasaki
- Motor Cagiva
- Motor Harley-Davidson
- Motor Texas
- Motor Bajaj
- Motor Derbi
- Motor Emco
- Motor Joy-it
- Motor Moto Guzzi
- Motor MV Agusta
- Motor Piaggio
- Motor Ridley
- Motor SMC
- Motor Victory
- Motor Zero
- Motor Hyosung
- Motor Sherco
- Motor Mash
- Motor Royal Enfield
- Motor Anova
- Motor Mahindra
- Motor CRRCpro
- Motor TVS
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
13 Oktober 2024
13 Oktober 2024
12 Oktober 2024
12 Oktober 2024