Indesit XWA 81482X W FR Bedienungsanleitung

Indesit Waschmaschine XWA 81482X W FR

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Indesit XWA 81482X W FR (16 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 6

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Load balancing system

Disposal

Description of the washing machine

and starting a wash cycle, 8-9

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 10

Push & Wash

Table of wash cycles

Personalisation, 11

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 12

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Troubleshooting, 13-14

Assistance, 15-16

XWA 81482

Instructions for use

WASHING MACHINE

English,1

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

( ).see figure

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

( ); the angle see figure

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the sup-

ply pipe by screwing

it to a cold water tap

using a ¾ gas threa-

ded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance . (see figure)

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details

table (see page 5).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100

cm from the floor;

The drain hose may

be connected to an

under-sink trap. Be-

fore connecting the

drain hose from the

machine ensure that

any blanks or remo-

vable ends have been

taken off the spigot.

If it is placed over the

edge of a basin or sink

be sure the free end of

the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length. Ensure that if the drain

hose is pushed into a standpipe, that the end does

not go down more than 15cms (6 inches). If the hose

is pushed down too far, this may cause the machine

to self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical

Data Plate fixed on the machine;

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

• the supply voltage is included within the values

indicated on the Technical Data Plate fixed on

the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fu-

sed plug it can be plugged into a 13 amp socket

for immediate use. Before using the appliance

please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words

on the base of the plug. Replacements can be

obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded

plug and you should wish to re-route the mains

cable through partitions, units etc., please en-

sure that either:

the plug is replaced by a fused 13 ampere rewi-

reable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in complian-

ce with BS 5733) which is accessible without

moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alterna-

tive plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

Produktspezifikationen

Marke:	Indesit
Kategorie:	Waschmaschine
Modell:	XWA 81482X W FR
Breite:	595 mm
Tiefe:	605 mm
Gewicht:	73400 g
Produktfarbe:	Weiß
Steuerung:	Buttons, Rotary
Höhe:	850 mm
Eingebautes Display:	Ja
Verpackungsbreite:	645 mm
Verpackungstiefe:	655 mm
Verpackungshöhe:	890 mm
Geräteplatzierung:	Freistehend
Waschprogramme:	Hygiene/anti-allergy, Black, Hand/wool, Wool, Shoes, Sport, Delicate/silk
Maximale Schleuderdrehzahl:	1400 RPM
Startzeitvorwahl:	Ja
Luftschallemission (Schleudern):	82 dB
Luftschallemmission (Waschen):	52 dB
Energieeffizienzklasse (alt):	A++
Jährlicher Energieverbrauch Waschen:	220 kWh
Ladetyp:	Frontlader
Energieverbrauch Reinigung:	1.2 kWh
Nennkapazität:	8 kg
Türanschlag:	Links
Jährlicher Wasserverbrauch Waschen:	11594 l
Schleuder-Klasse:	B
Rückstandsfeuchtigkeit:	53 %
Anzahl Waschprogramme:	16
Ladungsausgleichsystem:	Nein
Stromverbrauch (aus):	0.5 W
Trommelvolumen:	62 l
Überlaufschutz:	Ja
Trommel Volumen 2:	- l