Icom IC-M401EURO Bedienungsanleitung

Icom Empfänger IC-M401EURO

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Icom IC-M401EURO (49 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/49
INSTRUCTION MANUAL
iM401EURO
VHF MARINE TRANSCEIVER
If your vessel requires assistance, contact other vessels and
the Coast Guard by sending a distress call on Channel 16.
Or, transmit your distress call using digital selective calling on
Channel 70 (the optional DS-100 (#02) must be installed).
USING DIGITAL SELECTIVE CALLING (ch 70)
(DS-100 DSC CONTROLLER is required)
DISTRESS CALL PROCEDURE
1. Push and hold [DISTRESS] on the DS-100
for 5 sec. until you hear 5 short beeps
change to one long beep.
2. Wait for an acknowledgment from a coast
station.
Channel 16 is automatically selected.
3. Push and hold [PTT], then transmit the
appropriate information as at left.
USING CHANNEL 16
DISTRESS CALL PROCEDURE
1. “MAYDAY MAYDAY MAYDAY.”
2. “THIS IS ...............” (name of vessel)
3. Your call sign or other indication of the
vessel (AND 9-digit DSC ID if you have one).
4. “LOCATED AT ...............” (your position)
5. The nature of the distress and assistance
required.
6. Any other information which might facilitate
the rescue.
IN CASE OF EMERGENCY
i
Versions of the IC-M401EURO which display the “CE” symbol on the serial number seal, comply with the es-
sential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. òThis warn-
ing symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to
licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the
correct programming of this radio, to comply with national licensing requirement.
Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
ii
TABLE OF CONTENTS
INSTALLATION NOTES
The installation of this equipment should be
made in such a manner as to respect the EC
recommended electromagnetic field expo-
sure limits (1999/519/EC).
The maximum RF power available from this
device is 25 watts. The antenna should be
installed as high as possible for maximum ef-
ficiency and that this installation height
should be at least 5 meters above ground (or
accessible) level. In the case where an an-
tenna cannot be installed at a reasonable
height, then the transmitter should neither be
continuously operated for long periods if any
person is within 5 meters of the antenna, nor
operated at all if any person is touching the
antenna.
In all cases any possible risk depends on the
transmitter being activated for long periods.
(actual recommendation limits are specified
as an average of 6 minutes) Normally the
transmitter is not active for long periods of
time. Some radio licenses will require that a
timer circuit automatically cuts the transmit-
ter after 1–2 minutes etc.
Similarly some types of transmitter, SSB,
CW, AM, etc. have a lower ‘average’ output
power and the perceived risk is even lower.
1 OPERATING RULES .......................... 1
2 PANEL DESCRIPTION .................. 2 4
Panel description ............................. 2
Function display ............................... 3
Microphone ...................................... 4
3 BASIC OPERATION ...................... 6 9
Channel selection ............................ 6
Receiving and transmitting .............. 8
Call channel programming ............... 9
Memory channel names .................. 9
4 DUALWATCH/TRI-WATCH ......... 10–11
Description ..................................... 10
Operation ....................................... 10
5 SCAN OPERATION ................... 12 13
Scan types ..................................... 12
Setting tag channels ...................... 13
Starting a scan ............................... 13
6 SET MODE ................................. 14 15
Set mode programming ................. 14
Set mode items .............................. 15
7 CONNECTIONS AND
MAINTENANCE ......................... 16 20
Unpacking ...................................... 16
Antenna ......................................... 16
Fuse replacement .......................... 16
Cleaning ......................................... 16
Connections ................................... 17
Mounting the transceiver ............... 18
Dimensions ..................................... 20
8 TROUBLESHOOTING ...................... 22
9 CHANNEL LIST ................................ 23
10 SPECIFICATIONS AND OPTIONS ... 24
Specifications ................................. 24
Options .......................................... 24
MB-69 TEMPLATE


Produktspezifikationen

Marke: Icom
Kategorie: Empfänger
Modell: IC-M401EURO

Brauchst du Hilfe?

Wenn Sie Hilfe mit Icom IC-M401EURO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Empfänger Icom

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-