Hotpoint HSIC 3M19 C UK N Bedienungsanleitung

Hotpoint Spülmaschine HSIC 3M19 C UK N

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint HSIC 3M19 C UK N (8 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Before using the appliance carefully read Health and Safety guide.

APPLIANCE

PRODUCT DESCRIPTION

THANK YOU FOR BUYING A HOTPOINT ARISTON

PRODUCT. In order to receive a more complete assistan-

ce, please register your appliance on:

www.hotpoint.eu/register

You can download the Safety Instructions and

the Use and Care Guide, by visiting our website

docs.hotpoint.eu and following the Instructions on

the back of this booklet.

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

0000 000 00000

Service:

1011

1 2 3 4 5 6 7 8 9 10 11

1. ON-OFF/Reset button with indicator light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time indicator

6. Tablet indicator light

DAILY REFERENCE

GUIDE

CONTROL PANEL

7. Display

8. Half Load indicator lights

9. Half Load button

10. Delay button

11. START/Pause button with indicator light / Tab

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the reta-

ining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and should be lled when the SALT REFILL

indicator light in the control panel is lit .

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. -Only the rst time you do this: ll the salt re

servoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, we recommend carrying out the

procedure before the washing cycle is started.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for average (3) water hardness.

• Switch on the appliance by pressing the button.ON/OFF

• Switch o the appliance by pressing the button.ON/OFF

• Hold down button for 5 seconds, until you hear a beep.P

• Switch on the appliance by pressing the button.ON/OFF

• The current selection level number and the salt indicator light both ash.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch o the appliance by pressing the button.ON/OFF

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the

heating element may be damaged as a result.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 17 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should A

be lled when the indicator light in the control RINSE AID REFILL

panel is lit.

1. Open the dispenser B by pressing and pulling up the tab on the lid.

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satised with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the button.ON/OFF

• Switch it o using the button.ON/OFF

• Press button three times - a beep will be heard.P

• Switch it on using the button.ON/OFF

• The current selection level number and rinse aid indicator light ash.

• Press button P to select the level of rinse aid quantity to be supplied.

• Switch it o using the buttonON/OFF

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied.

The LOW RINSE AID indicator light will not be lit if you run out of rinse

aid.

A maximum of 4 levels can be set according to the dishwasher model.

The factory setting is specic to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

mid-range number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device A.

Introduce the detergent into the dry dispenser B only. Place the

amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser there are B

indications to help the detergent

dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the TABLET

button, because it adjusts the program so that the best washing and

drying results are always achieved.

Program

Drying

phase

Available

options *)

Detergent

container Duration of

wash program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Tub B

1Eco 50° 4:00 11.5 0.83

2Intensive 65° - 2:30 15.0 1.50

3Normal 55° - 2:30 15.0 1.30

4Daily 50° - 1:20 11.5 1.10

5Delicates

45°

- 1:40 11.5 1.00

6Express 30’ 50° - - 0:30 8.5 0.50

7Soak - - --0:10 4.5 0.01

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 50242.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 5 W - O mode consumption: 0.5 W

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1 ECO

Normally soiled crockery. Standard program, the most ecient in

terms of its combined energy and water consumption.

2 INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

3 NORMAL

Mixed soil. For normally soiled dishes with dried food residues.

4 DAILY

Normally soiled crockery. Everyday cycle, that ensures optimal cleaning

and drying performance in shorter time.

5 DELICATES

Program for delicate items, which are more sensitive to high tempera-

tures, for example glasses and cups.

6 EXPRESS 30’

Program to be used for lightly-soiled dishes with no dried food

residues.

7 SOAK

Use to refresh crockery planned to be washed later. No detergent to be

used with this program.

Notes:

Please note that cycles like Express or Fast are most eective for lightly

soiled dishes.

To reduce consumption even further, only run the dishwasher

when it is full.

Produktspezifikationen

Marke:	Hotpoint
Kategorie:	Spülmaschine
Modell:	HSIC 3M19 C UK N
Display-Typ:	LED
Breite:	448 mm
Tiefe:	555 mm
Gewicht:	29600 g
Steuerung:	Tasten
Höhe:	820 mm
AC Eingangsspannung:	230-240 V
AC Eingangsfrequenz:	50 Hz
Eingebautes Display:	Ja
Paketgewicht:	31600 g
Geräteplatzierung:	Voll integriert
Selbstreinigend:	Ja
Energieeffizienzklasse:	F
Kabellänge:	1.3 m
Energieeffizienzskala:	A bis G
Startzeitvorwahl:	Ja
Anschlusswert:	1900 W
Stromstärke:	13 A
Zykluszeit:	240 min
Trocknungsklasse:	A
Geräuschpegel:	49 dB
Halbe Beladung:	Ja
Türfarbe:	Silber
Trocknungssystem:	Statisch
Einschalteverzögerung (max.):	12 h
Wasserverbrauch pro Zyklus:	11.5 l
Waschwirkungsklasse:	A
Anzahl Waschprogramme:	7
Energieverbrauch pro 100 Zyklen:	84 kWh
Energieverbrauch pro Zyklus:	0.84 kWh
Lärmemissionsklasse:	C
Anzahl Maßgedecke:	10 Maßgedecke
Geschirrspülprogramme:	Eco, Glass/delicate, Mixed, Quick, Soak
Temperatur (max):	- °C
Produktgröße:	Standardgröße (60 cm)
Benutzerdefinierte Panel-Bereitschaft:	Ja
Bedienfeld Farbe:	Silber
Oberer Korb höhenverstellbar:	Ja
Einbauraum Breite:	600 mm
Einbauraum Tiefe:	560 mm
Anzeige bei geringem Füllstand an Salz:	Ja
Anzeige für fehlenden Klarspüler:	Ja
Einbauraum Höhe (min):	820 mm
Einbauraum Höhe (max):	900 mm
Schlauchlänge Wasserzulauf:	1.55 m
Schlauchlänge Wasserablauf:	1.5 m
Maximale Versorgungstemperatur für Warmwasser:	60 °C