Hotpoint HIC 3C26 WF UK Bedienungsanleitung

Hotpoint Spülmaschine HIC 3C26 WF UK

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint HIC 3C26 WF UK (8 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions and the Use

and Care Guide, by visiting our website

docs.hotpoint.eu and following the Instructions on the

back of this booklet.

Before using the appliance carefully read Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack

Cutlery rack

3. Foldable flaps

4. Upper rack height adjuster

5. Upper spray arm

6. Lower rack

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10.Detergent and Rinse Aid dispensers

11.Rating plate

12.Control panel

0000 000 00000

Service:

CONTROL PANEL

1. On-Off/Reset button with indicator light

2. Program selection button

3. Salt refill indicator light

4. Rinse Aid refill indicator light

5. Program number and delay time indicator

6. Delay indicator light

7. Display

8. Zone Wash 3D indicator light

9. Delay button

10.

Zone Wash

button

11. Tablet (Tab) button with indicator light

1 2 3 4 5 6 7 8 9 10 11

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see

PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL

indicator light in the control panel is lit.

1.Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2.Only the first time you do this: fill the salt

reservoir with water.

3.Position the funnel

(see figure)

and fill the salt

reservoir right up to its edge (approximately 1 kg);

it is not unusual for a little water to leak out.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for average (3) water hardness.

• Switch on the appliance by pressing the ON/OFF button.

• Switch off the appliance by pressing the ON/OFF button.

• Hold down button P for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing the ON/OFF button.

• The current selection level number and the salt indicator light both flash.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch off the appliance by pressing the ON/OFF button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches off.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be filled when the RINSE AID REFILL indicator light in the control

panel is lit.

1. Open the dispenser

by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml)

reference notch of the filling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button P three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The current selection level number and rinse aid indicator light flash.

• Press button P to select the level of rinse aid quantity to be

supplied.

• Switch it off using the ON/OFF button

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specific to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

high number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser

use the opening device A. Introduce

the detergent into the dry dispenser

B only. Place the amount of

detergent for pre-washing directly

inside the tub.

1.When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser

there are indi-

cations to help the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program. If all-in-one detergents are used, we

recommend using the

TABLET

button, because it adjusts the program so

that the best washing and drying results are always achieved.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 18 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories: for information on

comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 6 W - Off mode consumption: 0.5 W

Program

Drying

phase

ActivEco

Available options *)

Detergent

container Duration of

wash program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Tub B

1. Eco 50° 3:10 9.5 0.93

2. Auto Intensive 65° - - 2:00 - 3:10 14.0 - 17.0 1.50 - 1.85

3. Auto Normal 55° 1:30 - 2:30 14.5 - 16.0 1.15 - 1.30

4. Auto Fast 50° - - - 0:55 - 1:20 13.0 - 14.5 1.15 - 1.25

5. Express 30’ 50° - - - 0:30 9.0 0.55

6. Sanitizing 65° - - 1:40 10.0 1.30

7. Soak - - - - - 0:12 4.5 0.01

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

ECO

Normally soiled crockery. Standard program, the most efficient in terms

of its combined energy and water consumption.

AUTO INTENSIVE

Automatic program for heavily soiled dishes and pans (not to be used

for delicate items).

AUTO NORMAL

Automatic program for normally soiled pans and dishes.

AUTO FAST

Automatic program for limited quantity of normally soiled crockery.

Ensures optimal cleaning performance in shorter time.

EXPRESS 30’

Program to be used for lightly-soiled dishes with no dried food

residues.

SANITIZING

Normally or heavily soiled crockery, with additional antibacterial wash.

SOAK

Crockery to be washed later. No detergent to be used with this

program.

Notes:

Please note that cycles like Express or Fast are most effective for lightly

soiled dishes.

To reduce consumption even further, only run the dishwasher

when it is full.

Produktspezifikationen

Marke:	Hotpoint
Kategorie:	Spülmaschine
Modell:	HIC 3C26 WF UK
Display-Typ:	LED
Breite:	598 mm
Tiefe:	555 mm
Gewicht:	35500 g
Steuerung:	Tasten
Höhe:	820 mm
AC Eingangsspannung:	220 - 240 V
AC Eingangsfrequenz:	50 Hz
Eingebautes Display:	Ja
Paketgewicht:	37500 g
Geräteplatzierung:	Voll integriert
Selbstreinigend:	Ja
Kabellänge:	1.3 m
Energieeffizienzskala:	A+++ bis D
Startzeitvorwahl:	Ja
Energieeffizienzklasse (alt):	A++
Verstellbare Füße:	Ja
Anschlusswert:	1900 W
Stromstärke:	13 A
Jährlicher Energieverbrauch:	266 kWh
Zykluszeit:	190 min
Trocknungsklasse:	A
Geräuschpegel:	46 dB
Türfarbe:	Silber
Einschalteverzögerung (max.):	12 h
Wasserverbrauch pro Zyklus:	9.5 l
Anzahl Waschprogramme:	7
Energieverbrauch pro Zyklus:	0.93 kWh
Anzahl Maßgedecke:	14 Maßgedecke
Geschirrspülprogramme:	Auto, Eco 50°C, Intensive, Normal, Quick, Soak
Temperatur (max):	65 °C
Benutzerdefinierte Panel-Bereitschaft:	Ja
Bedienfeld Farbe:	Weiß
Oberer Korb höhenverstellbar:	Ja
Art des Besteckeinsatzes:	Korb
Abnehmbares Oberteil:	Ja
Einbauraum Breite:	600 mm
Einbauraum Tiefe:	560 mm
Anzeige bei geringem Füllstand an Salz:	Ja
Anzeige für fehlenden Klarspüler:	Ja
Einbauraum Höhe (min):	820 mm
Invertertechnologie:	Ja
Stromverbrauch (aus):	0.5 W
Wi-Fi-gesteuert:	Nein
Maximale Versorgungstemperatur für Warmwasser:	60 °C
Verstellbare Körbe:	höher
Leistungsaufnahme (eingeschaltet):	6 W
Dauer des eingeschalteten Modus:	12 min