Hotpoint CS1A 300 H Bedienungsanleitung

Hotpoint Gefrierschrank CS1A 300 H

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint CS1A 300 H (8 Seiten) in der Kategorie Gefrierschrank. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

INSTRUCTIONS FOR USE

DIAGRAM OF THE APPLIANCE (Fig. 1)

A. Handle.

B. Safety lock (if provided).

C. Gasket.

D. Separator (if provided).

E. Defrost water drain plug.

F. Control panel.

G. Side motor cooling grille.

DIAGRAM OF THE CONTROL PANEL (Fig. 2)

1. Temperature adjustment thermostat.

2. Red light (if provided): indicates that the temperature

inside the product is not low enough.

3. Green LED (if provided): when lit, indicates that the

appliance is running.

4. : Yellow/orange illuminated button (if provided)

activates/deactivates the fast freeze function.

When lit, it indicates that the fast freeze function is active.

The fast freeze function automatically deactivates after

about 50 hours.

The exact conguration of the control panel may vary

according to the model.

BEFORE USING THE APPLIANCE

Your new appliance is designed to be used in the

household and similar applications such as:

- kitchen areas in shops, oces and other working

environments

- farm houses

- by clients in hotels, motels, residences, bed &

breakfasts.

The product must only be used to store frozen food, to

freeze fresh food and to make ice.

Regulations require the appliance to be earthed. The

manufacturer declines all liability for injury to persons

or animals and for damage to property resulting

from failure to observe the above procedures and

reminders.

1. After unpacking, make sure that the appliance is

undamaged and that the door closes perfectly, with the

gasket remaining intact. Any damage must be reported to

your retailer within 24 hours after delivery of the appliance.

2. Wait at least two hours before switching the appliance on

in order to ensure the refrigerant circuit is fully ecient.

3. Installation and electrical connection must be carried out

by a qualied technician, according to the manufacturer’s

instructions and local safety regulations.

4. Clean the inside of the appliance before using it.

• Before connecting the appliance to the mains supply,

ensure that the voltage corresponds to that given on the

rating plate located on the rear of the appliance.

• Electrical connections must be made in accordance

with local regulations.

INSTALLATION

• Unpack the appliance.

• Remove the 4 spacers inserted between the door

and the appliance. (Fig 3)

• Make sure the defrost water drain plug (if provided) is

correctly positioned (E).

• For optimum appliance operation and to avoid damage

when the door is opened, leave a space of at least 7 cm

from the rear wall and 7 cm at the sides. (Fig. 4)

• Fit the accessories (if provided).

SWITCHING ON THE APPLIANCE

• The appliance is factory set for optimum operation at a

temperature of -18°C.

• Plug in the appliance.

• The green LED lights up (if provided).

• Also the red LED (if provided) will switch on because

the temperature inside the appliance is not yet

suciently low for food storage. The red LED will

normally switch o within the rst six hours after the

appliance is switched on.

• After connecting the appliance to the mains supply and

when the optimal temperature has been reached (this

phase takes about 1 hour during which the lid will not

open), ensure that the fast freeze button is not pressed

(the yellow LED, if provided, is o).

• Place food inside the product only when the red LED

(if provided) has switched o.

• Thanks to the ecient lid seal, the appliance lid will not

re-open easily immediately after closing. Wait a few

minutes before re-opening the lid of the appliance.

TEMPERATURE ADJUSTMENT

Use the thermostat to select the ideal storage temperature.

To adjust the internal temperature, proceed as follows:

• Turn the thermostat knob to 1 for a storage temperature

that is less cold.

• Turn the thermostat knob to 6 for a colder storage

temperature.

• For partial loads, or when the load indicator is below the

“e” symbol inside the appliance, it is advisable to move

the thermostat to the lower position (on “e”, if present on

the thermostat scale)

FREEZING FOOD

Preparation of fresh food for freezing

• Before freezing, wrap and seal fresh food in: aluminium

foil, cling lm, air and water-tight plastic bags,

polyethylene containers with lids, provided they are

suitable for freezing foods.

• Food must be fresh, mature and of prime quality in order

to obtain high quality frozen food.

• Fresh vegetables and fruit should preferably be frozen

as soon as they are picked to maintain the full original

nutritional value, consistency, colour and avour.

• Always leave hot food to cool before placing in the

appliance.

Freezing fresh food

• Place foods to be frozen in direct contact with the walls

of appliance (Fig. 5):

A) - foods to be frozen,

B) - foods already frozen.

• Avoid placing foods to be frozen in direct contact with

food already frozen.

• For best and fastest freezing, foods should be split into

small portions; this will also be useful when the frozen

items are to be used.

1. At least 24 hours before storing fresh food in the

appliance, press the fast freeze button (4).

2. Place the food to be frozen and keep the lid of the

appliance closed for 24 hours. The fast freeze function

automatically deactivates after about 50 hours.

FOOD STORAGE

Refer to the table on the appliance.

Classication of frozen foods

Load and classify the frozen foods; it is advisable

to indicate the storage date on the packs, to ensure

consumption before the expiry dates listed in months in

Fig. 6 for each type of food.

Advice for storing frozen food

When buying frozen food, make sure that:

• The packaging is intact (food in damaged containers

may have deteriorated). If a package is swollen or has

damp patches, the product may not have been stored

in optimum conditions and therefore undergone partial

defrosting.

• When shopping, leave frozen food purchases until last

and carry them in a thermally insulated bag.

• On arriving home, immediately place the frozen food in

the appliance.

• Avoid or minimise temperature variations. Observe the

expiry date on the packaging.

• Always follow the storage instructions on frozen food

packages.

Note:

• Eat fully or partially defrosted foods immediately.

Do not refreeze unless the food is cooked after it

has thawed. Once cooked, the food can be refrozen.

• In case of a prolonged power failure: Do not open

the appliance door, except to place ice packs (if

provided) over the frozen foods on the right and left

side of the appliance. This will slow down the rise in

temperature.

PRECAUTIONS AND SUGGESTIONS

• During installation, make sure the appliance does

not damage the power cable.

• Do not store glass containers with liquids inside the

product as they may break.

• Do not eat ice cubes or ice lollies immediately after

taking them out of the appliance as they may cause cold

burns.

• Before carrying out any maintenance or cleaning,

always unplug the appliance or disconnect the power

supply.

• Do not install the appliance in places exposed to

direct sunlight or near heat sources in order to avoid

increasing power consumption.

• Do not put aerosol spray cans or recipients containing

propellants or ammable substances in the appliance.

• Do not store or use gasoline or other ammable liquids

and gases in the vicinity of this or any other domestic

appliance. The fumes can create a re hazard or

explosion.

• Install the appliance in a perfectly horizontal position, on

a oor strong enough to take its weight and in an area

suitable for its size and use.

• Install the appliance in a dry, well-ventilated place.

The appliance is set for operation at specic ambient

temperature ranges, according to the climatic class

indicated on the data plate located at the rear of the

product (Fig. 7). The appliance may not work properly

if it is left for a long time at a temperature outside the

specied range.

• It is advisable to leave the appliance connected if left

empty even for short periods.

• Be careful not to damage the oors when you move the

appliance (e.g. parquet). To facilitate product handling,

it is advisable to empty it beforehand, if possible.

Note: The appliance must be handled and installed by two

or more persons.

• Do not use mechanical devices or any means other

than those recommended and/or supplied by the

manufacturer to speed up the defrosting process.

• Do not use electrical appliances inside the product,

unless such appliances are specically recommended

by the manufacturer.

• The bulb used inside the appliance is specically

designed for domestic appliances and is not suitable for

general room lighting within the home (EC Regulation

244/2009).

• This appliance must not be used by children under

8 years of age, or by people with limited physical,

sensory or mental abilities or without experience

and knowledge of it, unless instructed in its use by

those responsible for their safety.

• Do not allow children to play or hide inside the

product: risk of becoming trapped inside and

suocating.

• Power cable modication or replacement must only

be carried out by qualied personnel or After-sales

Service.

• Do not use extension leads or adapters.

• Electrical disconnection must be possible either by

unplugging the appliance or by means of a double-

pole switch located upline from the socket.

• Ensure that the voltage indicated on the appliance

data plate corresponds to the domestic supply

voltage.

• Do not ingest the contents (non-toxic) of the ice

packs (if provided).

• Restrict the number of times you open the door.

• This appliance features “skin condenser”

technology: the condensing unit is integrated into

the walls of the freezer. For this reason the side

and front walls of the product may become hot

while the product is running. This is entirely normal

and also reduces the risk of condensation forming

in particularly critical environmental conditions

(see paragraph “Troubleshooting guide”).

APPLIANCE DEFROSTING

The appliance should be defrosted when the thickness of

ice on the walls reaches 5-6 mm.

• Disconnect the appliance from the power supply.

• Remove food from the appliance and put it in a very

cool place or a thermally insulated bag.

• Leave the appliance door open.

• Remove the internal defrost water drain plug (depending

on model) (Fig. 8).

• Remove the external defrost water drain plug

(depending on model) and reposition it as shown in

g. 8.

• Use the separator (depending on model) inside the

product as a recipient for any remaining water, (D) as

shown in g. 8. If there is no separator, use a shallow

container.

• Defrosting can be sped up by using a spatula to detach

the frost from the appliance walls.

• Remove the frost from the bottom of the appliance.

• In order to avoid permanent damage to the

appliance interior, do not use pointed or sharp

metal instruments to remove the ice.

• Do not use abrasive products or heat up the

interior articially.

• Dry the inside of the appliance thoroughly.

• Ret the plug after defrosting.

CLEANING AND MAINTENANCE

• Remove the frost from the upper edges (see

Troubleshooting Guide).

• Clean the inside after defrosting, using a sponge

dampened with warm water and/or mild detergent.

• Clean the side vent (if provided).

Unplug the appliance before carrying out maintenance

operations. Do not use abrasive products, scourers

or stain-removers (e.g. acetone, trichloroethylene) to

clean the appliance.

To obtain the best results from your appliance, carry

out cleaning and maintenance at least once a year.

HANGING THE LID LIGHT BULB (if provided)

• Disconnect the appliance from the mains power supply.

• Remove the diuser by following the sequence of steps

shown in the gure.

• Unscrew the light bulb and replace it with an identical

bulb of the same wattage and voltage.

• Ret the diuser and plug in the appliance.

TROUBLESHOOTING GUIDE

1. The red LED (if provided) remains alight.

• Is there a power failure?

• Is defrosting in progress?

• Is the appliance lid properly closed?

• Is the appliance positioned near a heat source?

• Is the thermostat setting correct?

• Are the ventilation grille and condenser clean?

2. The appliance is too noisy.

• Is the appliance perfectly horizontal?

• Is the appliance in contact with other furniture or objects

that may cause vibrations?

• Has the packaging been removed from under the

appliance?

Note: Gurgling noises from the refrigerating circuit after the

compressor cuts out are perfectly normal.

3. The green LED (if provided) is o and the

appliance is not working.

• Is there a power failure?

• Is the plug properly inserted in the socket?

• Is the electric cable intact?

4. The green LED (if provided) is o and the

appliance is working.

• The green LED is not working. Contact the After Sales

Service for a replacement.

5. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long time?

• Is the appliance positioned in a very warm room or near

heat sources?

• Is the thermostat setting correct?

• Has the fast freeze function (depending on model) been

pressed by mistake?

6. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly

positioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed? (See

chapter “Installation”)

• Have the 4 protection pieces been removed? (See

chapter “Installation”)

7. Condensation forms on the external walls of the

appliance

• It is normal for condensation to form under certain

atmospheric conditions (humidity above 85%) or if the

appliance is located in a damp or poorly ventilated

room.

The performance of the appliance is in no way aected.

8. The layer of ice on the internal walls of the

appliance is not uniform.

• This phenomenon is quite normal.

SAFEGUARDING THE ENVIRONMENT

1. Packing

The packing material is 100% recyclable and bears the

recycling symbol . For disposal, comply with the local

regulations. Keep the packing materials (plastic bags,

polystyrene parts, etc.) out of the reach of children, as they

are a potential source of danger.

2. Scrapping/Disposal

The appliance is manufactured using recyclable material.

This appliance is marked in compliance with European

Directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring the correct disposal of

this appliance, you can help prevent potentially negative

consequences for the environment and the health of

persons.

The symbol on the appliance, or on the accompanying

documents, indicates that this appliance should not be

treated as domestic waste but must be taken to a special

collection centre for the recycling of electrical and electronic

equipment.

When scrapping the appliance, make it unusable by cutting

o the power cable and removing the doors and shelves

so that children cannot easily climb inside and become

trapped.

Produktspezifikationen

Marke:	Hotpoint
Kategorie:	Gefrierschrank
Modell:	CS1A 300 H
Breite:	1180 mm
Tiefe:	690 mm
Produkttyp:	Truhe
Produktfarbe:	Weiß
Höhe:	910 mm
Sperren:	Ja
Verpackungsbreite:	1210 mm
Verpackungstiefe:	760 mm
Verpackungshöhe:	960 mm
Geräteplatzierung:	Freistehend
Energieeffizienzklasse (alt):	A+
Jährlicher Energieverbrauch:	278 kWh
Geräuschpegel:	42 dB
Türanschlag:	Hoch
Nutzinhalt Gefrierfach:	311 l
Bruttokapazität Gefrierfach:	- l
Gefrierkapazität:	20 kg/24h
Lagerzeit bei Störung:	- h
Sternekennzeichnung:	4*
Klimaklasse:	SN-T
Abtauautomatik (Gefriereinheit):	Ja
Schnellfrost-Funktion:	Ja
Gefrierfachtemperatur (min):	-18 °C