Hotpoint AQ113F497E Bedienungsanleitung

Hotpoint Waschmaschine AQ113F497E

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint AQ113F497E (16 Seiten) in der Kategorie Waschmaschine. Dieser Bedienungsanleitung war für 29 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/16

English,1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 6-7

Control panel

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent

Preparing the laundry

Washing recommendations

Precautions and advice, 11

General safety

Load balancing system

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 13-14

Assistance, 15-16

WASHING MACHINE

AQUALTIS

AQ113F 497 E

Instructions for

installation and use

Installation

! This instruction manual should be kept in a safe place

for future reference. If the washing machine is sold, given

away or moved, please ensure the manual is kept with

the machine, so that the new owner may benefit from the

advice contained within it.

! Read these instructions carefully: they contain vital

information relating to the safe installation and operation of

the appliance.

! Inside the pack containing this manual, you will also find

the guarantee and all the details necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the

washing machine, make sure it has not been damaged

during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4 protective

screws (used during

transportation) and the

corresponding spacer,

located on the rear part of

the appliance ( ). see figure

3. Close off the holes using the plastic plugs supplied in the

pack.

4. Keep all the parts in a safe place; they will be needed

again if the washing machine is moved to another location,

to prevent the inside of the appliance being damaged.

! Packaging materials should not be used as toys for

children.

Levelling

1. Place the washing machine on a flat sturdy floor, without

resting it up against walls, cabinets anything else.

2. If the floor is uneven, the

front feet of the machine

may be adjusted until

it reaches a horizontal

position (the angle of

inclination must not exceed

2 degrees).

! If the appliance is levelled correctly, it will be more stable

and much less likely to cause vibrations and noise while it

is operating, particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space underneath

the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water supply, run

the water until it is perfectly clear.

1. Connect the inlet hose

to the machine by screwing

it onto the cold water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part of

the appliance . (see figure)

2. Connect the inlet hose

by screwing it to a cold

water tap using a 3/4 gas

threaded connection (see

figure).

3. Make sure that the hose is not folded over or bent.

! The water pressure at the tap must fall within the values

indicated in the Technical data table (see page 5).

! If the inlet hose is not long enough, contact a specialised

shop or an authorised technician.

! Never use second-hand or old inlet hoses; use the

products supplied with the machine.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

The drain hose may

be connected to an

under-sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the spigot.

If it is placed over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

! We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Ensure that if the drain hose is pushed into a standpipe,

that the end does not go down more than 15cms

(6 inches). If the hose is pushed down too far, this may

cause the machine to self -syphon ie. continuously

empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Technical Data

Plate fixed on the machine.

• the supply voltage is included within the values indica-

ted on the Technical Data Plate fixed on the machine.

• the socket is compatible with the washing machine’s

plug. If this is not the case, replace the socket or the

plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable plug

bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet,

controlled by a switch, (in compliance with BS 5733) which

is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Produktspezifikationen

Marke:	Hotpoint
Kategorie:	Waschmaschine
Modell:	AQ113F497E
Display-Typ:	LCD
Timer:	Ja
Breite:	590 mm
Tiefe:	630 mm
Produktfarbe:	Tungsten, White
Höhe:	850 mm
Eingebautes Display:	Ja
Geräteplatzierung:	Freistehend
Waschprogramme:	Hygiene/anti-allergy, Black, Steam
Maximale Schleuderdrehzahl:	1400 RPM
Startzeitvorwahl:	Ja
Energieeffizienzklasse (alt):	A+++
Ladetyp:	Frontlader
Energieverbrauch Reinigung:	- kWh
Nennkapazität:	11 kg
Türanschlag:	Rechts
Wasserverbrauch pro Zyklus:	- l
Waschwirkungsklasse:	A
Schleuder-Klasse:	B