Honeywell Performance HEW2PER2 Bedienungsanleitung

Honeywell Sicherheitskamera Performance HEW2PER2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell Performance HEW2PER2 (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
HEW2PER2 WDR 4 MP IR Bullet Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series IP
camera. Follow the instructions in this guide to install and log in
to your camera. For instructions on configuring the camera,
refer to the Performance Series IP Cameras User Guide on the
installation CD that came with your camera.
If you require additional assistance, contact Tech Support
(contact info is listed on the back page).
Cautions and Warnings
WARNING
To ensure compliance with electrical safety standards, this product is intended for
use with a Listed Power Adapter marked “Limited Power Source” or “LPS” on the unit,
output rated to 12 VDC, minimum 0.33 A, TMA=60 deg C, or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting IEEE
802.3af PoE standard.
WARNING
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
• Read and keep these instructions.
• Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where
the operating temperature is outside the recommended range of -22°F to 140°F (–30°C to
60°C).
Note
Do not apply power to the camera before completing installation.
Confirm the installation surface can support at least three times the weight of the
camera.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
or damaged, contact your dealer immediately.
• Camera
• Installation CD
• Quick installation guide
• Allen key (L- wrench)
• Self-tapping screws (×4)
• Plastic wall anchors (×4)
• Mounting template
Preparing the Mounting Surface
Inspect the site where you want to install the camera. The mounting
surface must be flat and capable of supporting at least three times
the weight of the camera.
Remove the backing from the mounting template sticker and affix
the sticker to the mounting surface.
Note If you are using the side exit for the cable, note the
orientation of the cable exit notch. In outdoor installations the notch
should point downwards to prevent water from entering the camera
housing.
Drill three screw holes at the locations indicated on the mounting
template sticker and insert the three supplied plastic anchors in the
holes.
If you are flush mounting the camera and want to store the cables
inside the wall or ceiling, drill a hole at the cable exit position on the
mounting template and then pull the cables through the hole.
CAUTION
THIS SYMBOL INDICATES THAT
DANGE OUSR VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CA : TUTION O REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REM THE COVE OVER.
NO USER-SERVICEABLE PAR .TS INSIDE
REFER SER TO QU RVICING ALIFIED SE VICE
PERSONNEL.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY T.THIS UNI
RISK OF ELECTRIC
SHOCK
DO N T OPENO
© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.
Mounting the Camera
1. Loosen the locking screw on the camera enclosure to remove
the enclosure from the camera base.
2. If local storage is needed, insert a m icroSD card into the
m icroSD card slot ( ). refer to the right picture
3. Route the cables through the camera base.
4. Align the screw holes on the camera base with the plastic wall
anchors.
5. Attach the camera base to the mounting surface using the
supplied screws.
6. Connect the camera with the Ethernet cable and the power
cable.
a. Connect one end of the Ethernet cable to the RJ-45 port
on the camera.
b. If the other end of the Ethernet cable is NOT connected to
a PoE (Power-over-Ethernet) switch or NVR, connect the
power connector of the camera to a 12 VDC power source.
7. Reattach the enclosure to the base and tighten the locking
screw.
8. Rotate the camera body to the desired position.
Adjusting Zoom and Focus
If the camera a is connected to the PoE port of Honeywell Embedded NVR, you can log on to the
camera directly from the NVR.
To log on to the camera from a : PC
1. Install the Honeywell Config Tool from the installation CD.
2. Use the Config Tool to discover the camera and open the camera’s webpage.
3. Log on to the camera as the admin user. The default user name is admin -(case sensitive) and
the default password is 1234.
Note • Be sure to remember the password of the camera. If the password is lost, the
camera may need to be sent back to the factory for recovery.
• Only Internet Explorer 11 (or later) is supported.
• IP address of the device is assigned automatically by DHCP server. If the DHCP
server is not available, the device will acquire 192.168.1.108 as the default IP
address.
4. Go to Setup
Camera
Conditions
Zoom and Focus. The following panel appears:
• Click Zoom in Zoom out + or - to zoom in or out.
• Click Near - or Far + to focus near or far, or click to enable auto focus.Auto Focus
Recommended Recorders
HEN*4
8/16/32/64-channel Focus 4K NVRs (H.264 and H.265)
HEN*3 4/8/16/32 (H.264 -channel Performance Series NVRs ) and H.265
HEN*2 4/8/16 - channel Performance Series NVRs (H.264)
HRHT4* - 4/8/16 channel 4 MP HQA/IP/CVBS Hybrid DVRs (H.264)
Regulatory Statements
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES- 003.
Manufacturer’s Declaration of Conformance
North America ied with this guide conforms to UL 60950The equipment suppl -1 and CSA C22.2 No.
60950 1.-
Europe The manufacturer declares that the equipment supplied is compliant with the European
Parliament and Council Directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and
the essential requirements of the EMC directive (2014/30/EU), conforming to the requirements of
standards EN 55032 for emissions, EN 50130 4 for immu- nity, and EN 62368-1 for electrical equipment
safety.
WEEE (Waste Electrical and Electronic Equipment)
Correct disposal of this product (applicable in the European Union and other European
countries with separate collection systems). This product should be disposed of, at the end of
its useful life, as per applicable local laws, regulations, and procedures.
Honeywell
2700 Blankenbaker Pkwy,
Suite 150
Louisville, KY, 40299, USA
www.honeywell.com/security
+1 800 323 4576
(North America only)
Aston Fields Road, Whitehouse
Industrial Estate
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
+1 44 (0) 1928 754 028
(Europe only)
Building #1, 555 Huanke Road,
Zhang Jiang Hi- Tech Park
Pudong New Area, Shanghai,
201203, China
www.asia.security.honeywell.com
+400 840 2233
(Asia Pacific only)
Document 800-2459 /20182 – – 08Rev A

Produktspezifikationen

Marke: Honeywell
Kategorie: Sicherheitskamera
Modell: Performance HEW2PER2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell Performance HEW2PER2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheitskamera Honeywell

Honeywell

Honeywell Acuix HDVFNWBC Bedienungsanleitung

2 Mai 2024
Honeywell

Honeywell Acuix HDVFNWAC Bedienungsanleitung

27 März 2024
Honeywell

Honeywell HDZ30HD Bedienungsanleitung

24 März 2024
Honeywell

Honeywell HCCM474M Bedienungsanleitung

27 Februar 2024
Honeywell

Honeywell Equip HCD1F Bedienungsanleitung

15 Februar 2024
Honeywell

Honeywell HEN08122 Bedienungsanleitung

10 Februar 2024
Honeywell

Honeywell HRGX85 Bedienungsanleitung

29 Januar 2024
Honeywell

Honeywell Equip HDZ30 Bedienungsanleitung

29 Januar 2024
Honeywell

Honeywell HN30080208 Bedienungsanleitung

27 Januar 2024
Honeywell

Honeywell Acuix HDXANDASW Bedienungsanleitung

22 Januar 2024

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024
ZKTeco

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024
Moxa

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024