Honeywell HZ-335 Bedienungsanleitung

Honeywell Herd HZ-335

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell HZ-335 (5 Seiten) in der Kategorie Herd. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
IMPORTANT
SAFEGUARDS
READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS
HEATER.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the
following:
IMPORTANT
INSTRUCTIONS
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surface. If provided, use han-
dles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet (0.9 m)
from the front of the heater and keep them away from
the sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
dropped or damaged in any manner. Return heater
to authorized service facility for examination, electri-
cal or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathroom, laun-
dry areas and similar moist indoor locations. Never
locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or the like. Arrange cord
away from traffic areas where it will not be tripped
over.
9. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of shock,
this plug is intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a quali-
fied electrician. DO NOT attempt to defeat this
safety feature.
10. This heater draws 12.5 amps during operation. To
prevent overloading a circuit, do not plug the heater
into a circuit that already has other appliances work-
ing.
11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet (recepta-
cle) and plug may cause overheating and distortion
of the plug. Contact a qualified electrician to replace
loose or worn outlet.
12. To disconnect the heater, first turn controls to the
OFF position, then grip the plug and pull it from the
wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside.
Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stored.
16. Use this heater only as described in this manual.
Any other use not recommended by the manufac-
turer may cause fire, electric shock, or injury to per-
sons.
17. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
18. The output of this heater may vary and its tempera-
ture may become intense enough to burn exposed
skin. Use of this heater is not recommended for per-
sons with reduced sensitivity to heat or an inability to
react to avoid burns.
19. SAVE THESE
INSTRUCTIONS.
1
POWER
MODE
OSCILLATE
70
°
F
F/C
DIGITAL CERAMIC
HEATER
HZ-335, HZ-336 Series
2
BASIC CONTROL PANEL OPERATION:
POWER
MODE: SET TEMPERATURE
MODE: SET TIMER
FAHRENHEIT/CELSIUS
Continuous Run High Power
Low Power
• Press Power once to start the heater on High Power,
Continuous Run.
• Press Power again to change to Low Power, Continuous
Run.
• Press Power a third time to turn the heater off.
Set Temperature
• Press Mode until the Temperature icon blinks. The
current room temperature will appear.
• Use the Up or Down arrows to set the desired tem-
perature.
• The Temperature icon will stop blinking and the cur-
rent room temperature will reappear after the
desired temperature is set.
• The heater will turn-off shortly after the desired tem-
perature is reached and the Power light above the
display will blink.
• The heater will turn back on when the room temper-
ature drops approximately 2 degrees below the
desired temperature. The Power light will stop
blinking and will remain lit.
Timer
• Press Mode until the Timer icon blinks. The Hour
display will appear.
• Use the Up or Down arrows to set an operation time
between 1 and 10 hours.
• The heater will turn-off when time runs out.
F/C Temperature
Display
• F/C feature functions from only the Power or Set
Temperature screens.
• Press the F/C button to toggle between Fahrenheit
and Celsius.
3
OSCILLATION
REMOTE CONTROL OPERATION (HZ-336
SERIES):
Two (2) AAA batteries required.
Model HZ-336:
Remote Control included when originally pur-
chased.
Model: HZ-335:
Remote Control may be purchased separately at:
www.honeywellconumerproducts.com
The Remote Control works the same as the cor-
responding buttons on the Control Panel. The
Control Panel display on the heater will show the
appropriate icons when the various functions are
activated.
POWER:
MODE: SET TEMPERATURE
• The Oscillation feature functions in any power or
mode setting.
• Press the Oscillation button to toggle this feature on
and off.
High Power
Low Power
• Press Power once to start the heater on High Power,
Continuous Run.
• Press Power again to change to Low Power, Continu-
ous Run.
• Press Power a third time to turn the heater off.
Power
Basic Remote LCD Remote
• Press Mode until the Temperature icon blinks. The
current room temperature will appear.
• Use the Up or Down arrows to set the desired temper-
ature.
• The Temperature icon will stop blinking and the current
room temperature will reappear after the desired tem-
perature is set.
• The heater will turn-off shortly after the desired tem-
perature is reached and the Power light above the dis-
play will blink.
• The heater will turn back on when the room tempera-
ture drops approximately 2 degrees below the desired
temperature. The Power light will stop blinking and will
remain lit.
Mode
Adjust Up or
Down
Set Temperature
Basic Remote LCD Remote


Produktspezifikationen

Marke: Honeywell
Kategorie: Herd
Modell: HZ-335

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell HZ-335 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Herd Honeywell

Bedienungsanleitung Herd

Neueste Bedienungsanleitung für -Kategorien-