Honeywell HBD7S Bedienungsanleitung

Honeywell Überwachungskamera HBD7S

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell HBD7S (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
HBD7S(X) Bullet Camera Quick Installation Guide
Document 800-15430 – Rev A – 07/2013
Introduction
Thank you for purchasing a Honeywell HBD7S(X) bullet camera. Follow the instructions in this guide to
install your camera. To configure the camera settings, refer to the HBD7S(X) Bullet Ca
mera Configuration
Guide.
Important Safety Instructions
• Read and keep these instructions.
• Please ensure that your installation area can safely support the weight of the camera.
• Do not aim the camera toward an extreme light source to prevent damage to the CCD.
• Do not touch the camera lens or bezel (front glass plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of 14°F to 122°F [–10°C to 50°C]).
Dimensions
Installing the Camera
Before You Begin
Before you begin installing the camera, check that you have received all of the parts listed below.
If any parts are missing or damaged, contact your dealer immediately.
Connecting the Camera Cable
1. Connect the camera’s video output to the video input on your monitor or DVR.
2. Connect the camera’s power input to a 12 V DC or 24 V AC power supply.
WARNING
Installation and servicing should be performed only
by qualified and experienced technicians to conform to all local
codes and to maintain your warranty.
WARNING
This device is configured for 12 V DC or 24 V AC
operation. Do not connect to a higher voltage. Use only with NTRL-
approved Class 2 power supplies.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
DO NOT OPEN
RISK OF ELECTRIC SHOCK
• Camera (cable included)
• Manuals
• Video test cable
• DC power pigtail
• Mounting plate
• Focus and zoom adjustment tool
• 4 socket head cap screws
• 4 pan head screws
• 1 hex key
8.54″ (217 mm)
4.84″ (123 mm)
3.68″ (93.5 mm)
3.27″ (83 mm)
1
BNC Video Out (Yellow)
DC Power Jack (Red)
www.honeywell.com/security
+1 800 323 4576 (North America only)
https://www.honeywellsystems.com/ss/techsupp/index.html
Document 800-15430 – Rev A – 07/2013
© 2013 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without wri
tten permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell
cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
HBD7S(X) Bullet Camera Quick Installation Guide
Mounting the Camera
1. Using a Phillips driver (not su to the mounting surface (with the pplied), attach the mounting plate
foam side facing the wall) using the four supplied 1-inch (25.4 mm) pan head screws,
2. Using the supplied hex key, attach the camera and bracket to the mounting plate using the four
supplied 3/8-inch (9.52 mm) socket head cap screws. Ensure that the notch in the bracket base is
facing down.
Positioning the Camera
After the camera is mounted, adjust the multidirectional bracket to set the camera’s field of view.
There are three adjustment points.
1. Loosen the adjustment screws with the supplied hex key, move the camera to the desired position,
and then tighten the screws.
2. Loosen the adjustment ring, move the camera to the desired position, and then tighten the ring.
Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
1. Unscrew the cap on the underside of the camera to access the
focus and zoom controls.
2. Connect the supplied video test cable to VIDEO TEST and
connect the other end to a portable service monitor.
3. Adjust the camera’s focus and zoom settings using the supplied
tool. If the focus and zoom adjustment screws do not move
freely, loosen the lock screw.
4. Tighten the lock screw to prevent the focus and zoom settings
from changing as a result of camera vibration.
Configuring the Camera
The camera is programed using on-screen display (OSD) menus.
These menus are controlled by the built-in OSD joystick on the underside of the camera
(next to the focus and zoom controls).
• Press down and hold the OSD joystick for two seconds to
bring up the OSD main menu on the connected monitor.
• Push the joystick up or down to move up or down through
the list of menu options.
• Press down on the joystick to to enter a submenu (
) or
to execute (set) a menu selection.
• Push the joystick left or right to change a menu setting.
360° 360°
180°
Adjustment
screw
Adjustment
screw
Adjustment
ring
2
ZOOM FOCUS
LOCK
SET UP
VIDEO TEST
LENS
DC
MANUAL
EXPOSURE
SHUTTER
AGC
SENSE-UP
BLC
D-WDR
RETURN
WHITE BALANCE
ATW
AWB
AWC->SET
MANUAL
DAY&NIGHT
COLOR
B/W
AUTO
EXT
3DNR
OFF
ON
SPECIAL
CAM TITLE
D-EFFECT
MOTION
PRIVACY
DEFECT
DEFOG
RETURN
ADJUST
SHARPNESS
MONITOR
RESET
FACTORY
RETURN
EXIT
3
SET UP

Produktspezifikationen

Marke: Honeywell
Kategorie: Überwachungskamera
Modell: HBD7S

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell HBD7S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Überwachungskamera Honeywell

Honeywell

Honeywell Equip HCD5WIH Bedienungsanleitung

20 September 2024
Honeywell

Honeywell iPCAM-PT Bedienungsanleitung

25 August 2024
Honeywell

Honeywell HN30160200 Bedienungsanleitung

17 August 2024
Honeywell

Honeywell HDZ30A Bedienungsanleitung

14 August 2024
Honeywell

Honeywell HDZ36AEX Bedienungsanleitung

10 August 2024
Honeywell

Honeywell Acuix HDV1NDFSW Bedienungsanleitung

9 August 2024
Honeywell

Honeywell Enterprise HERC96T24S Bedienungsanleitung

9 August 2024
Honeywell

Honeywell HC30W45R3 Bedienungsanleitung

7 August 2024
Honeywell

Honeywell HBL6GR2-LPR Bedienungsanleitung

6 August 2024
Honeywell

Honeywell HC30WF5R1 Bedienungsanleitung

5 August 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024
D-Link

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024
Foscam

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024
Alecto

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024
Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024