Honeywell HBD3PR2 Bedienungsanleitung

Honeywell Überwachungskamera HBD3PR2

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell HBD3PR2 (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
H BD3PR2 True Day/Night Indoor/Outdoor IR
Bullet IP Camera Regulatory Statements
Information to the User: This has equipment been and tested found to comply with the limits afor
Class B digital device, pursuant to part 15 of the Rules. FCC These limits are designed to provide
reasonable against protection harmful interference a in residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that a particular interference will not occur in installation.
Quick Installation Guide
Document 800 2123 10/2015- 3 — A– V1 Rev
Thank you for purchasing a HBD3PR2 c . amera
Follow the
instructions in this guide and to install
log to
your camera. For instructions on
configuring the
camera, refer to the Performance
Series IP
Cameras User Guide on the software
and
documentation CD that came with your
camera. If
you require additional assistance,
please call the
number shown below.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment is and off on, the user encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the the separation between equipment and receiver.
Connect the equipment into an outlet a that on circuit different from to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Cautions and Warnings
•
Note Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This B Class digital apparatus complies Canadian with ICES- 003.
Cet appareil numérique de la B à Classe est conforme la - Canada. norme NMB 003 du
Important Safeguards
WARNING
•
•
Read and keep these instructions.
Do not aim the camera toward a bright light source for extended periods to prevent damage to
the imager. Avoid operating the unit under or close to unstable light sources (may cause
flickering), or close to fluorescent lamps or objects reflecting light.
Do not touch the camera lens.
Do not drop the camera or subject it to physical shock.
Do not use a strong or abrasive detergent when cleaning the camera.
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the
operating temperature is outside the recommended range of - 4°Fto 140°F (– 20°C to 60°C).
To ensure compliance with electrical safety standards this product is
intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,
on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over
Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE
802.3af PoE standard. •
•
•
•
The Ethernet connection is not intended to be connected to exposed (outside plant)
networks. Do not connect two power sources to the camera at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam. Note
Do not apply power to the completing installation. camera before
Note
Confirm the installation surface can support at least three times the weight of the camera plus
the bracket.
Document 800 2123 /2015- 3 – A – V1 Rev 10 1
H BD3PR2 True Day/Night Indoor/Outdoor IR Bullet IP Camera
Before you begin, that check you all have received of the parts listed below. If any parts are missing
or your damaged, contact dealer immediately.
•
•
•
•
Camera
Documentation CD
Quick install guide
Allen key (L- wrench)
•
•
•
Self- 3)tapping screws (×
Plastic wall anchors 3)(×
Mounting template
2
b. Insert the microSD card into the microSD card slot as
shown in the picture at right.
c. Replace the control panel.
2. Connect the camera with the Ethernet cable and the power
cable.
Required tools:
•
•
A Phillips screwdriver
A drill with an appropriately- sized drill bit for pre- drilling holes for the screw anchors.
CAUTION
Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain your
warranty.
3
Aiming the Camera
1.
Use the supplied Allen key to loosen the adjusting screws
on the bracket arm.
2. Set the camera to the desired position.
3. Tighten the adjustment screws.
1
Preparing the Mounting Surface
1. Inspect the site where you want to install the camera. The mounting surface must be
flat and capable of supporting at least three times the weight of the camera.
2. Remove the backing from the mounting template sticker and affix the sticker to the
mounting surface.
Note If you are using the side exit for the cable, no te the orientation of the cab le exit
no tch. In out oor d ins ltal ati no rons the tch should point downwa ds to prevent wat fr er om
enteri ng the ca i mera hous ng.
Document - 3 – – 800 2123 V1 Rev A 10/2015
© 5 201 Honeywell this publication International Inc. All rights reserved. No part of may be reproduced by any means without written permission fro m Honeywell. The information in this publication is believed to be accurate in all respects. However,
Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to to Revisions editions change without notice. or new this publication may be issued such to incorporate changes.
3. Dr ho at lo tions a till three screw les the ca indic ted on he moun ng tem te ic r ti pla st ke and
in t e th e a ic an in holeser th re suppl plied st chors the s.
4. If you nt to sto b i wa re the ca les nside the wall drill hole i or ceil ng, a ca i o tionat the ble ex t p si
on i p the mount ng tem late and then pull the thr s cable ough the hole.
Mounting the Camera
1. If local storage is needed, i m nsert a icro SD card into the micro SD card slot
according to the following steps:
a. Use a Phillips screwdriver (not supplied) and remove the control panel cover
on the outside of the camera.
4
Adjusting the Zoom and Focus Settings
The c connected to a PoE port of the Honeywell Embedded NVR can be configured ameras
with the NVR directly.
To log on to the camera with a PC, perform the following steps:
1. Install the Honeywell Config Tool from the software and the documentation CD, find the
camera and open the web browser with the Honeywell Config Tool
2. Log on to the camera as the -admin user. The default user name is admin (case sensitive)
and the default password is 1234.
3. Go to Setup   Camera Conditions Zoom and Focus. The following panel appears:
• Click Zoom in – + or Zoom out to zoom in or out.
• Click Near – + or Far to focus near or far, or click Auto Focus to enable auto focus.
a. Connect one end of the Ethernet cable to the RJ- 45 port on the camera.
b. (PowerIf the other end of the Ethernet cable is NOT connected to a PoE - -over
Ethernet) switch or NVR, connect the power connector of the camera to a 12 V
DC power source.
3. Attach the camera assembly to the mounting surface using the supplied screws.

Produktspezifikationen

Marke: Honeywell
Kategorie: Überwachungskamera
Modell: HBD3PR2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell HBD3PR2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Überwachungskamera Honeywell

Honeywell

Honeywell Equip HCD5WIH Bedienungsanleitung

20 September 2024
Honeywell

Honeywell iPCAM-PT Bedienungsanleitung

25 August 2024
Honeywell

Honeywell HN30160200 Bedienungsanleitung

17 August 2024
Honeywell

Honeywell HDZ30A Bedienungsanleitung

14 August 2024
Honeywell

Honeywell HDZ36AEX Bedienungsanleitung

10 August 2024
Honeywell

Honeywell Acuix HDV1NDFSW Bedienungsanleitung

9 August 2024
Honeywell

Honeywell Enterprise HERC96T24S Bedienungsanleitung

9 August 2024
Honeywell

Honeywell HC30W45R3 Bedienungsanleitung

7 August 2024
Honeywell

Honeywell HBL6GR2-LPR Bedienungsanleitung

6 August 2024
Honeywell

Honeywell HC30WF5R1 Bedienungsanleitung

5 August 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024
D-Link

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024
Foscam

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024
Alecto

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024
Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024