Honeywell CT50K1028/E1 Bedienungsanleitung

Honeywell Thermostat CT50K1028/E1

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Honeywell CT50K1028/E1 (16 Seiten) in der Kategorie Thermostat. Dieser Bedienungsanleitung war fĂĽr 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
Owner’s Manual
English: Page 1
Mode d’emploi
Français : Page 6
Manual de Uso
Español: Página 11
CT50 Series Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2019 Honeywell International Inc.
All rights reserved.
Read and save these instructions
M23786
MERCURY NOTICE
If your old thermostat contains
mercury, contact your local waste
management authority for proper
disposal instructions.
TURN OFF POWER at heating/cooling system (or fuse/circuit-breaker panel).
Remove cover and thermostat, but leave wallplate with wires attached.
Temperature Control Range
• 45°–95°F (7°–35°C)
• 35°–85°F (2°–29°C); select models; for garages or other outbuildings.
Is there a sealed tube containing mercury?
If so, see mercury notice below.
Leave wallplate in place.
Old thermostat Cover
Check package contents:
• Thermostat
• Wall anchors & screws (2 each)
• Wire labels
Before you begin, make sure you have:
• No. 2 Phillips & small pocket
screwdrivers
• Hammer
• Level (optional)
• Pencil
• Drill and bit (3/16” for drywall, 7/32” for
plaster)
Getting started
Remove your old thermostat
Vertical Mount:
CT50 (24 Vac heating systems)
CT51 (24 Vac heating and cooling systems)
CT53 (750 mV or 12Vdc heating systems)
Horizontal Mount:
CT54 (24 Vac heating systems)
CT55 (24 Vac heating and cooling systems)
69-2040EFS-04
CT50 Series • Owner's Manual
69-2040EFS—04 2
M23789
M23787
M23790
M23788
Wrap supplied labels securely around each wire. let wires fall into wall opening!Do not
IGNORE WIRE COLORS: Use only letter
designations to identify wire types.
For CT51/CT55: If your old
thermostat has 7 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
CT50/CT53/CT54
1. Pull wires
through base.
2. Level base if
desired.
3. Mark positions
of both screw
holes.
For CT50/CT53/CT54: If your old
thermostat has 3 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with
the label matching the letter on your old thermostat. (Adhesive labels are supplied in your
thermostat package.)
Remove the old wallplate only all wires are labeled. Be careful not to let loose wires fall after
into the wall opening.
Label wires and remove old wallplate
Mark mounting position
CT51/CT55
CT50/CT53/CT54 CT51/CT55
English: • Français : • Español: Page 1 Page 6 Página 11
3 69-2040EFS—04
Wiring CT50/CT53/CT54
• 2-wire heat-only system: Connect one
wire to terminal, one wire to terminal.R W
M23791
Wiring CT51/CT55
[1] If wires will be connected to both and R Rc
terminals, remove the metal jumper.
[2] Do not connect both and if you have a O B
heat pump. Connect only the wire. Wrap O B
wire with electrical tape and do not use.
[3] Do not use or . Wrap bare end of wire C X, B
with electrical tape.
1. Drill holes at pencil-marked
locations (3/16” holes for
drywall, 7/32” holes for
plaster).
2. Use hammer to tap anchors
into holes until flush with wall.
3. Pull wires through thermostat
base and insert screws.
Check level if desired, then
tighten screws.
Mount thermostat base
1. Match each labeled wire with same
letter on terminal.
2. Use a screwdriver to loosen
screw terminals, insert bare wires
beneath screws, then tighten
screws.
3. Push any excess wire back into the
wall opening.
Labels don't match?
If labels do not match letters on
thermostat, see table below.
Existing wires Connect to:
R 5 • • RH • Terminal “ V R” [1]
Rc Terminal “Rc” [1]
O Terminal “O” [2]
B Terminal “B” [2]
G F • Terminal “G”
W W1 H • • Terminal “W”
Y Y1 M• • Terminal “Y”
C X B • • Do not use [3]
CT51/CT55
CT50/CT53/CT54
Connect wires


Produktspezifikationen

Marke: Honeywell
Kategorie: Thermostat
Modell: CT50K1028/E1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell CT50K1028/E1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Thermostat Honeywell

Bedienungsanleitung Thermostat

Neueste Bedienungsanleitung fĂĽr -Kategorien-