Hikvision DS-2CE56D5T-VPIR3 Bedienungsanleitung

Hikvision Überwachungskamera DS-2CE56D5T-VPIR3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hikvision DS-2CE56D5T-VPIR3 (6 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
TURBO HD
1080P Dome Camera
User Manual
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
UD.6L0201D1548A01
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
1.2 Overview
1.2.1 Overview of Type I Dome Camera
1.2.2 Overview of Type Dome Camera
II
1 Introduction
1.1 Product Features
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l Support IR cut filter with auto switch;
l OSD menu, parameters are configurable;
l Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
l SMART IR mode;
l Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Ceiling Mounting
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2 Loosen the screws on the bubble of type 1
.
camera /rotate the bubble of type2 camera to
remove the bubble and the black liner.
Figure 2-2 Remove the Bubble
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
2 Installation
Before you start:
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to DS-2CE56D5T-(A)VFIR and
DS-2CE56D5T-(A)VPIR3.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
DISCLAIMER STATEMENT
Underwriters Laboratories Inc. (UL has not)
tested the performance or reliability of the
security or signaling aspects of this product.
UL has only tested for fire, shock or casualty
hazards as outlined in Ul’s Standard(s) for Safety,
UL60950-1. UL Certification does not cover the
performance or reliability of the security or
signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING
0100001040603
THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.
Figure 1-1 Overview of Type I Dome Camera
Figure 1-2 Overview of Type Dome CameraII
Type I: Type I :I
Type I :I
Type I:
Auxiliary Video Output
Black Liner
Bubble
Power Cable
HD Video Cable
CVBS Cable
Lens
Base plate
CVBS Cable
Back Box
Lens
Bubble
Black Liner
Power Cable
HD Video Cable
Auxiliary Video Output
Dip Switch
Dip Switch
3 Menu Operation
Figure 3-1 Main Menu
Menu
SCENE LENS RESET
EXPOSURE WB DAY&NIGHT
BACKLIGHT NR SPECIAL ADJUST
INDOOR
OUTDOOR
INDOOR1
LOW-
LIGHT
MANUAL SHUT T ER
AGC
SENS-UP
BRIGHT NESS
D-WDR
DEFOG
BLC
HSBLC
ATW
AWC-SET
MANUAL
COLOR
B/W
EXT
2D NR
3D NR
CAM
TITLE
D-EFFECT
MOTION
PRIVACY
LAUGUAGE
DEFECT
VERSION
SHARPNESS
MONITOR
LSC
VIDEO.
OUT
EXIT
SETUP
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS ---|------ 40
5. DEFOG OFF
6. D-WDR OFF
7. RETURN RET
Figure 3-2 Exposure
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,
and x15 are selectable.
: You can set the AGC value from 0 to 15.AGC
: You can set the SENS-UP to OFF or AUTO.SENS-UP
: You can set the brightness valueBRIGHTNESS
from 1 to 100.
: You can set the defog function as ON toDEFOG
enable the function. Position, size, and the defog
gradation are configurable.
You can set the D-WDR as ON or OFF.D-WDR:
3.3.4 Backlight
Backlight Compensation (BLC):
Set the gain of BLC as High, Middle, or Low.-GAIN:
Press the up/down/left/right button to-AREA:
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
Restore the BLC settings to the default.-Default:
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to define the area position and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
HSBLC
1. SELECT AREA 1
2. DISPLAY ON 8
3. LEVEL ---|------ 40
4. MODE ALL DAY
5. BLACK MASK ON
6. DEFAULT 8
7. RETURN RET
Figure 3-3 HSBLC
3.3.5 White Balance (WB)
MANUAL, ATW (Auto-tracking White Balance),
AWCSET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D NR status as ON or OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
2D&3D NR
1. 2DNR OFF
2. 3DNR ON 8
3. RETURN RET
3D NR
1. SMART NR ON8
2. LEVEL ------|--8 0
3. START. AGC -|--------10
4. END. AGC -|--------10
5. RETURN RET
Figure 3-4 NR
Figure 3-5 3D NR
3.3.8 SPECIAL
Edit the camera title on this section.Camera Title:
D-effect:
Set the freeze function as ON or OFF.-FREEZE:
OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the position from PAN & TILT.
The D-Zoom area, sensitivity-SMART D-ZOOM:
and time are configurable.
Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:
SPECIAL
1. CAM TITLE ON 8
2. D-DFFECT 8
3. MOTION OFF
4. PRIVACY OFF
5. LANGUAGE ENG 8
6. DEFECT 8
7. RETURN RET
Figure 3-6 Special
MOTION
1. SELECT AREA 1
2. DISPLAY ON8
3. SENSITIVITY ----|---- 30
4. MOTION VIEW ON
5. DEFAULT 8
6. RETURN RET
Figure 3-7 Motion Detection
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
button to define the position and size of the area.
Set the SENSITIVITY from 0 to 60. Set the MOTION
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this section.
PRIVACY
1. SELECT AREA 1
2. DISPLAY MOSAIC 8
3. COLOR 10
4. TRANS. 1
5. DEFAULT 8
6. RETURN RET
ADJUST
1. SHARPNESS --------|15
2. MONITOR LCD8
3. LSC OFF
4. RETURN RET
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LSC status as ON or OFF.LSC
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
Figure 3-8 Privacy Mask Figure 3-9 Adjust
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Screw the bolts through the mount by aligning
with the 2 bolt holes. Fit the toggles onto the bolts.
3.Push the two toggle bolts through the two screw
holes on the ceiling. Rotate the bolt till the toggle
holds the ceiling tightly.
2.2 In-ceiling Mounting
Figure 2-5 Install the Mount
Figure 2-6 Fix the Camera to the Mount
Figure 2-8 Fix the Camera to the Gang Box
6. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
4.Route and connect the corresponding cables.
5.Fix the camera to the in-ceiling mount with the
supplied screws.
3.Attach the back box of type 1 camera /base plate
of type2 camera to the ceiling and secure them
with supplied self-tapping screws.
4.Route the cables through the cable hole.
5.Align the camera with the back box/base plate,
and tighten the set screws to secure the camera
with the back box/base plate.
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure below
to get an optimum angle.
8. Fit the black liner on the camera and tighten the
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
Figure 2-4 Zoom and Focus Adjustment
You need to purchase an in-ceiling mount separately
if you adopt in-celling mounting.
2.3 In-ceiling Mounting with
Gang Box
Only the type 1 camera supports in-ceiling
mounting with gang box.
1.Repeat steps 2-3 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied)
to the gang box.
Figure 2-7 Install the Mount
2.Route and connect the corresponding cables.
3.Align the camera with the gang box, and tighten
the screws to secure the camera with the gang box..
4. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
Type I: Type I :IType I :IType I :I
0 ~90° °
0 ~355° °
0 ~355° °
P
P
P
PP Direction
Direction
Direction
DirectionDirection
R
R
R
RR Direction
Direction
Direction
DirectionDirection
T
T
T
TT Direction
Direction
Direction
DirectionDirection
Type I:
0°~355°
0 ~90° °
0 ~340° °
T
T
T
TT Direction
Direction
Direction
DirectionDirection
R
R
R
RR Direction
Direction
Direction
DirectionDirection
P
P
P
PP Direction
Direction
Direction
DirectionDirection
Type I :I
Type I: Type I :I
You can call the menu and adjust the camera
parameters with a coaxial camera controller
(purchase separately). You can also call the menu
with supported TVI DVR.


Produktspezifikationen

Marke: Hikvision
Kategorie: Überwachungskamera
Modell: DS-2CE56D5T-VPIR3

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hikvision DS-2CE56D5T-VPIR3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Überwachungskamera Hikvision

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-