Hikvision DS-2CE56D5T-AIRZ Bedienungsanleitung

Hikvision Sicherheitskamera DS-2CE56D5T-AIRZ

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hikvision DS-2CE56D5T-AIRZ (4 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

TURBO HD

1080P Dome Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FC C

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

UD.6L0201D1818A01

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "C E" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

1 Introduction

1.1 Product Features

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2 Installation

Before you start:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0100001050521

Figure 1-1 Overview of Type I Camera

Figure 1-2 Overview of Type CameraII

Privacy Notice

Surveillance laws vary by jurisdiction. Check all

relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Please refer to the product specification for

camera parameters and functions.

Type

Model

DS-2C E56D5T-AIRZ

DS-2CE56D5T-AVPIR3Z

DS-2C E56D5T-AVPIR3ZH

HD Video Cable

CVBS Cable

Lens

AC24V Power Cable

Black Liner

Bubble

DIP Switch

Auxiliary Video Output

Base Plate

Menu Joystick

2.1 Ceiling Mounting

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Loosen the screws on the bubble of type 1

camera /rotate the bubble of type2 camera to

remove the bubble and the black liner.

Figure 2-2 Remove the Bubble

Type I: Type I :I

Type I :IType I:

3.Attach the back box of type 1 camera /base plate

of type2 camera to the ceiling and secure them

with supplied self-tapping screws.

4.Route the cables through the cable hole.

Menu Joystick

CVBS Cable

Black Liner

Lens

Bubble

Auxiliary Video Output

DIP Switch

Base Plate

HD Video Cable

AC24V Power Cable

l High performance CMOS sensor and high

resolution bring high-quality image;

l Turbo HD output, up to 1080P resolution;

l 2.8 – 12mm motorized vari-focal lens;

l OSD menu, parameters are configurable;

l Support Day/Night switch;

l SMART IR mode ;

l Support UT C function;

Built-in heater.

The built-in heater function varies according to

different models.

Industry Canada IC ES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

3 Menu Operation

Figure 3-1 Main Menu

DAY&NIGHT

BACKLIGHT

INDOOR

OUTDOOR

INDOOR1

LOW-

LIGHT

MANUAL SHUTT ER

AGC

SENS-UP

BRIGHTNESS

D-WDR

DEFOG

BLC

HSBLC

ATW

AWC-SET

MANUAL

COLOR

B/W

EXT

2D NR

3D NR

CAM

TIT LE

D-EFFECT

MOT ION

PRIVACY

LAUGUAGE

DEFECT

VERSION

SHARPNESS

MONITOR

LSC

VIDEO.

OUT SETUP

SMART

FOCUS

You can call the menu and adjust the camera

parameters with a coaxial camera controller

(purchase separately). You can also call the menu

with supported T VI DVR.

3.1 VID EO.OUT

PAL or NT SC is selectable .

3.2 LANGUAG E

English, Japanese, CH N1, CHN2, Korean, German,

French, Italian, Spanish, Polish, etc., are selectable.

3.3 SETUP

3.3.2 SCENE

You can select indoor, outdoor, indoor 1 and low

-light as the working environments.

3.3.3 LENS

The camera is equipped with 2.8-12mm motorized

vari-focal lens.

3.3.4 EXPOSURE

EXPOSURE

1. SHUTTER AUTO

2. AGC OFF

3. SENS-UP ---

4. BRIGHTNESS ---|------ 40

5. DEFOG OFF

6. D-WDR OFF

7. RETURN RET

Figure 3-2 Exposure

SHUTTER: AUT O,1/25, 1/50, FLK, 1/200, 1/400,

1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

and x15 are selectable.

: You can set the AGC value from 0 to 15.AGC

: You can set the SENS-UP to OFF or AU TO.SENS-UP

: You can set the brightness valueBRIGHT N ESS

from 1 to 100.

: You can set the defog function as ON toDEFOG

enable the function. Position, size, and the defog

gradation are configurable.

You can set the D-W DR as ON or O FF.D-WDR:

3.3.5 Backlight

Backlight Compensation (BLC):

Set the gain of B LC as High, Middle, or Low.-GA IN:

Press the up/down/left/right button to-AREA:

define the BLC position and size. Select RET or

AGAI N to go back the BLC menu or re-define the

BLC area.

Restore the BLC settings to the default.-Default:

HSBLC: Select an H SBLC area. Set the DISP L AY

status as ON. Press the up/down/left/right button

to define the area position and size. Set the H SBL C

LE VEL from 0 to 100. Select ALL DAY or Night for the

HSBLC mode. Set the BLAC K MASK status as ON or

OF F.

HSBLC

1. SELECT AREA 1

2. DISPLAY ON 8

3. LEVEL ---|------ 40

4. MODE ALL DAY

5. BLACK MASK ON

6. DEFAULT 8

7. RETURN RET

Figure 3-3 H SB LC

3.3.6 White Balance (WB)

MANUAL, AT W (Auto-tracking White Balance),

AWC→SET are selectable.

3.3.7 Day & Night

Color, B/W, and EXT are selectable for DAY and

NI GHT switches.

3.3.8 NR

: You can set 2D NR status as O N or OFF.2D N R

: Set the Smart NR status as ON and adjust3D N R

the 3D smart N R sensitivity ranges from 0 to 100.

Set the 3D N R LEV E L ranges from 0 to 100. Set the

2D&3D NR

1. 2DNR OFF

2. 3DNR ON 8

3. RETURN RET

3D NR

1. SMART NR ON8

2. LEVEL ------|--8 0

3. START. AGC -|--------10

4. END. AGC -|--------10

5. RETURN RET

Figure 3-4 NR

Figure 3-5 3D N R

3.3.9 SPECIAL

Edit the camera title on this section.Camera Title:

D-effect:

Set the freeze function as O N or OF F.-FREEZE:

OF F, MI RROR, V-FLIP, and ROTATE a re-MIRROR:

selectable for mirror.

Define the zoom area by configuring-D-ZOOM:

the position from PAN & TILT.

The D-Zoom area, sensitivity-SMART D-ZOOM:

and time are configurable.

Set the NEG IMAGE as ON or OFF.-N EG.IM AGE:

SPECIAL

1. CAM TITLE ON 8

2. D-DFFECT 8

3. MOTION OFF

4. PRIVACY OFF

5. DEFECT 8

6. RETURN RET

Figure 3-6 Special

MOTION

1. SELECT AREA 1

2. DISPLAY ON8

3. SENSIT IVITY ----|---- 30

4. MOTION VIEW ON

5. DEFAULT 8

6. RETURN RET

Figure 3-7 Motion Detection

Motion: Select a MOT ION area. Set the DISP L AY

status as ON or OF F. Press the up/down/left/right

button to define the position and size of the area.

Set the SENSI T IVI T Y from 0 to 60. Set the M OT ION

VIEW status as ON or OFF.

Privacy: Select a P RIVACY area. Set the DISP LAY

status as INV, MOSAIC, COLOR or OF F. Press the

up/down/left/right button to define the position

and size of the area.

Defect: LI VE DPC, STATIC DP C and Black DPC a re

adjustable in this section.

PRIVACY

1. SELECT AREA 1

2. DISPLAY MOSAIC 8

3. COLOR 10

4. TRANS. 1

5. DEFAULT 8

6. RETURN RET

ADJUST

1. SHARPNESS --------|15

2. MONITOR LCD8

3. LSC OFF

4. RETURN RET

3.3.10 ADJUST

: Adjust the sharpness from 0 to 15.Sharpness

: Monitor C RT, and Monitor LC D areMonitor

selectable.

: Set the LSC status as O N or OFF.LSC

3.3.11 RESET

Reset all the settings to the default.

3.3.12 EXIT

Press OK to exit the menu.

START. AGC level as the threshold to enable AGC,

and set the END. AGC level as the threshold to

disable AGC.

Figure 3-8 Privacy Mask Figure 3-9 Adjust

3.3.1 S MART FOCUS

Move the joystick to adjust the camera lens by the

FOC US+, F OCUS-, ZOOM + a nd ZO OM-. T he smart

focus value turns higher when the focusing

effectiveness turns better. The value range is 0~99.

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Screw the bolts through the mount by aligning

with the 2 bolt holes. Fit the toggles onto the bolts.

3.Push the two toggle bolts through the two screw

holes on the ceiling. Rotate the bolt till the toggle

holds the ceiling tightly.

2.2 In-ceiling Mounting

Figure 2-5 Install the Mount

4.Route and connect the corresponding cables.

5.Fix the camera to the in-ceiling mount with the

supplied screws.

Figure 2-3 Fix the Camera to the Ceiling

6. Connect the corresponding cables.

7. Adjust the camera according to the figure below

to get an optimum angle.

8. Fit the black liner on the camera and tighten th e

screws on the bubble of type 1 camera or rotate the

bubble of type 2 camera to complete.

Figure 2-4 3-axis Adjustment

You need to purchase an in-ceiling mount separately

if you adopt in-celling mounting.

Type I: Type I :IType I :IType I :I

PP Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

TT Direction

Direction

DirectionDirection

Type I:

TT Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

PP Direction

Direction

DirectionDirection

Type I :I

5.Align the camera with the back box/base plate,

and tighten the set screws to secure the camera

with the back box/base plate.

Type I: Type I :I

Figure 2-6 Fix the Camera to the Mount

Figure 2-8 Fix the Camera to the Gang Box

6. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

2.3 In-ceiling Mounting with

Gang Box

Only the type 1 camera supports in-ceiling

mounting with gang box.

1.Repeat steps 2-4 of the In-ceiling Mounting

section to secure the in-ceiling mount (supplied)

to the gang box.

Figure 2-7 Install the Mount

2.Route and connect the corresponding cables.

3.Align the camera with the gang box, and tighten

the screws to secure the camera with the gang box..

4. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

0°~75°

0°~355°

0°~340°

0°~355°

0°~75°

Produktspezifikationen

Marke:	Hikvision
Kategorie:	Sicherheitskamera
Modell:	DS-2CE56D5T-AIRZ
WLAN:	Nein
Gewicht:	560 g
Produktfarbe:	Weiß
Übertragungstechnik:	Kabelgebunden
Höhe:	101 mm
Befestigungstyp:	Zimmerdecke
AC Eingangsspannung:	24 V
Betriebstemperatur:	-20 - 45 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 90 %
Eingebauter Ethernet-Anschluss:	Nein
Power over Ethernet (PoE):	Nein
Typ:	CCTV Sicherheitskamera
Stromverbrauch (max.):	6 W
Unterstützte Sprachen:	ARA, CHI (SIMPL), CHI (TR), DEU, DUT, ENG, ESP, FRE, HEB, ITA, JPN, KOR, POL, POR, RUS, TUR
Analoges Signalformatsystem:	NTSC, PAL
Unterstützte Video-Modi:	1080p
Unterstützte Grafik-Auflösungen:	1920 x 1080 (HD 1080)
Rauschverhältnis (SNR):	62 dB
Full-HD:	Ja
Zoom-Fähigkeit:	Ja
Digitaler Zoom:	62 x
Geräuschunterdrückung:	Ja
Blickwinkel (FOV):	103 °
PTZ Kontrolle:	Ja
Schwenkbereich:	0 - 355 °
Neigungswinkelbereich:	0 - 75 °
Formfaktor:	Kuppel
Durchmesser:	136 mm
Maximale Auflösung:	1944 x 1092 Pixel
Unterstützung von Positionierung:	Indoor
DC-Ausgang Volt:	12
Brennweitenbereich:	- mm
Bis zu 30 Frames pro Sekunde:	25 fps
Megapixel insgesamt:	2 MP
Anzahl der Kameras:	1
Tag/ Nachtmodus:	Ja
Mindestbeleuchtung:	0 Lux
Nachtsichtdistanz:	30 m
LED Typ:	IR
Sensor-Typ:	CMOS
Weißabgleich:	ATW, AWC, Manual
Nachtsicht:	Ja
Wide Dynamic Range (WDR):	Ja
Drehungswinkel:	355 °
Maximale Blendenzahl:	1.4
Flip & Spiegel:	Ja
Datenschutz-Maskierung:	Ja
Infrarot (IR)-Abschaltfilter:	Ja
Composite Video-Ausgang:	1
Teilnehmerausgang:	1
Bewegungssensor:	Ja
Output Widerstand:	75 Ohm
Anzahl der Sprachen:	16