Hikvision DS-2CE56D0T-ITME Bedienungsanleitung

Hikvision Überwachungskamera DS-2CE56D0T-ITME

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hikvision DS-2CE56D0T-ITME (12 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
TURBO HD TVI
Bullet & Turret Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the model listed below.
Type
Model
Type I
DS- -2CE16D0T IT1E/3E/5E
Type II
DS- - 2CE16D0T IRE/IRPE
Type III
DS- -2CE56D0T IT1E/3E
This manual may contain several technically incorrect
places or prinng errors, and the content is subject to
change without noce. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
010 001 80420 0 3
Regulatory Informaon
FCC Informaon
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protecon
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instrucon manual, may cause harmful interference to
radio communicaons. Operaon of this equipment in a
residenal area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Condions
This device complies with part 15 of the FCC Rules.
Operaon is subject to the following two condions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operaon
EU Conformity Statement
This product and if applicable the - -
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the EMC Direcve 2014/30/EU,
the RoHS Direcve 2011/65/EU.
2012 19/ /EU (WEEE direcve): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collecon
points. For more informaon see: www.recyclethis.info.
Industry Canada ICES 003 Compliance-
This device meets the CAN ICES 3 (A)/NMB- -3(A)
standards requirements.
Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Safety Instrucon
These instrucons are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precauon measure is divided into “Warnings” and
“Cauons”
Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cauons: Injury or equipment damage may occur if any
of the cauons are neglected.
Warnings
In the use of the product, you must be in strict
compliance with the electrical safety regulaons of
the naon and region.
Refer to technical specicaons for detailed
informaon.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12 V
DC according to the IEC60950 1 standard. Refer to -
technical specicaons for detailed informaon.
Do not connect several devices to one power adapter
as adapter overload may cause over heang or a re -
hazard.
Make sure that the plug is rmly connected to the
power socket.
When the product is mounted on wall or ceiling, the
device shall be rmly xed.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cable, and
then contact the service center.
If the product does not work properly, contact your
dealer or the nearest service center. Never aempt to
disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.)
Cauons
Make sure the power supply voltage is correct before
using the camera.
Do not drop the camera or subject it to physical
shock.
Do not touch senor modules with ngers. If cleaning
is necessary, use clean cloth with a bit of ethanol and
wipe it gently.
Do not aim the camera at the sun or extra bright
places. Blooming or smearing may occur otherwise
(which is not a malfuncon), and aect the
endurance of sensor at the same me.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cauons Follow these
precauons to prevent
potenal injury or
material damage.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not place the camera in extremely hot, cold, dusty
or damp locaons, and do not expose it to high
electromagnetic radiation.
To avoid heat accumulaon, good venlaon is
required for operating environment.
Keep the camera away from liquid while in use.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
Introducon
1.1 Product Features
The camera is applicable for both indoor and outdoor
condions, and the applicaon scenarios include road,
warehouse, parking lot, oice, campus, etc..
The main features are as follows:
High performance CMOS sensor
1080p resoluon
Auto white balance
Auto electronic shutter
Auto gain control (AGC)
IR cut lter
PoC
3 axis adjustment-
Note:
Type camera is applicable for indoor condion only.III
1.2 Overview
1.2.1 Type I Camera Overview
Power Cord
Video Cable
Mounng Base
Sun Shield
Lens
Figure 1. 1 Type I Camera Overview
1.2.2 Type II Camera Overview
Power Cord
Mounng
Base
Main Body
Lens
IR LED
Video Cable
Figure 1. 2 Type III Camera Overview
1.2.3 Type III Camera Overview
Enclosure
Camera
Mounng
Base
Power Cord
Video Cable
Figure 1. 3 Type II Camera Ov erview
Installaon
2.1 Installaon Preparaon
Before you start:
Make sure that the device in the package is in good
condion and all the assembly parts are included.
Make sure that all the related equipment power off is -
during the installaon.
Check the specificaon of the products for the
installaon environment.
Check whether the power supply is matched with
your power output to avoid damage.
Make sure the wall is strong enough to withstand
three mes the weight of the camera and the
mounng bracket.
If the wall is cement, insert expansion bolts before
installing the camera. If the wall is wooden, use
self tapping screws to secure the camera.-
If the product does not funcon properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.
2.2 Installaon of Type I Camera
Before you start:
Both wall mounting and ceiling mounng are suitable
for the bullet camera. Ceiling mounting will be taken as
an example in th secon. You can take the steps of is
ceiling mounng as a reference, when adopng the wall
mounng.
Steps:
1. Paste the dill template to the ceiling.
2. Drill the screw holes according to the drill template,
and the cable hole (oponal) on the ceiling.
Figure 2. 1 Drill Template
Note:
Cable hole is required when adopng ceiling outlet
to route the cable.
3. Attach the mounng base of the type I camera to
the ceiling and secure the camera with supplied
screws.
Figure 2. 2 Secure the Camera to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement wall, expansion bolts are required to x
the camera. For wooden wall, self-tapping screws
are required.
4. Route the cables through the cable hole (oponal),
or the side opening.
5. Connect the corresponding power cord, video and
cable.
6. Power on the camera to check whether the image
on the monitor is goen from the opmum angle.
If not, adjust the camera according to the gure
below to get an opmum angle.
to 9
to 360°
to 360°
1
2
3
Figure 2. 3 3-Axis Adjustment
1) Loosen the No.1 adjusting screw to adjust the
pan position (0° to 360°).
2) Tighten the No.1 adjusng screw.
3) Loosen the No.2 adjusting screw to adjust the
lng posion (0° to 90°).
4) Tighten the No. 2 adjusng screw.
5) Loosen the No.3 adjusting screw to adjust the
rotaon posion (0° to 360°).
6) Tighten the No.3 adjusng screw.
2.3 II Installaon of Type Camera
Before you start:
Both wall mounting and ceiling mounng are suitable
for the bullet camera. Ceiling mounting will be taken as
an example in th secon. You can take the steps of is
ceiling mounng as a reference, when adopting wall
mounng.
Steps:
1. Paste the dill template to the ceiling.
2. Drill the screw holes according to the drill template,
and the cable hole (oponal) on the ceiling.
47.6
13.7 27.5
Φ 68
3-Φ 4
Unit: mm
Figure 2. 4 Drill Template
Note:
Cable hole is required when adopng ceiling outlet
to route the cable.
3. Attach the mounng base of the type I camera to
the ceiling and secure the camera with supplied
screws.
Figure 2. 5 Secure the camera to the ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement wall, expansion bolts are required to x
the camera. For wooden wall, self-tapping screws
are required.
4. Route the cables through the cable hole (oponal),
or the side opening.
5. Connect the corresponding power cord and video
cable.
6. Power on the camera to check whether the image
on the monitor is goen from the opmum angle.
If not, adjust the camera according to the gure
below to get an opmum angle.
to 360°
1
2
3
to 360° to 180°
Figure 2. 6 3-Axis Adjustment
1). Loosen the No.1 adjusting screw to adjust the
pan position (0° to 360°).
2). Tighten the No.1 adjusng screw.
3). Loosen the No.2 adjusting screw to adjust the
lng posion (0° to °).180
4). Tighten the No. 2 adjusng screw.
5). Loosen the No.3 adjusting screw to adjust the
rotaon posion (0° to 360°).
6). Tighten the No.3 adjusng screw.
2.4 Installaon of Type II camera
Before you start:
Both wall mounting and ceiling mounng are suitable
for the turret camera. Ceiling mounng will be taken as
an example in th secon. You can take the steps of is
ceiling mounng as a reference, when adopting wall
mounng.
Steps:
1. Disassemble the turret camera by rotang the
camera to align the notch to one of the marks, as
shown in Figure 2. 1.
Mark
Notch
Figure 2. 7 Disassemble the Camera
2. Remove the mounng base from the camera body
with a at object, e.g., a coin.
3. Paste the drill template (supplied) to the place
where you want to install the camera, and then drill
the screw holes and the cable hole (oponal) on the
ceiling according to the drill template.
Screw Hole
Cable Hole
Figure 2. 8 Drill Template
Note:
Cable hole is required when adopng the ceiling
outlet to route the cable.
4. Attach the mounng base to the ceiling and secure
them with supplied screws
Figure 2. 9 Aach the Mounng Base to the Ceiling
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement wall, expansion bolts are required to x
the camera. For wooden wall, self-tapping screws
are required.
5. Route the cables through the cable hole (oponal),
or the side opening.
6. Align the camera with the mounng base, and
ghten the screws to secure the camera with the
mounng base.
Figure 2. 10 Secure the Camera with Mounng Base
7. Connect the corresponding cables, such as power
cord, and video cable.
8. Power on the camera to check whether the image
on the monitor is goen from the opmum angle. If
not, adjust the camera according to the gure below
to get an opmum angle.
Tilt Posion Range
[0°to 75°]
Pan Posion Range
[0° to 360°]
Rotaon Posion Range
[0°to 360°]
Figure 2. 11 3-axis Adjustment
1). Hold the camera body and rotate the enclosure
to adjust the position [ 360°].pan to
2). Move the camera body up and down to adjust
the lt posion [0° to 75°].
3). Rotate the camera body to adjust the rotaon
posion [0° 360°].to
Menu Descripon
Purpose:
Call the menu by clicking buon on the PTZ Control
interface, or call the preset No.95.
Steps:
1. Connect the camera with the TVI DVR, and the
monitor, shown as the gure 3 1.-
Camera
TVI DVR
Monitor
Figure 3. 1 Connecon
2. Power on the analog camera, TVI DVR, the and
monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking buon, or call
the preset No. 95.
AE EXPOSURE MODE
MAIN MENU
VIDEO
SETTINGS
SAVE EXIT&
AGC
RETURN
DWDR
CONTRAST
SHARPNESS
COLOR GAIN
DNR
MIRROR
RETURN
RESET
BRIGHTNESS
IMAGE
MODE
WB
RETURN
MODE
FORMAT
LANGUAGE
DAY-NIGHT
INFRARED
SMART IR
RETURN
MODE
Figure 3. 2 Main Menu Overview
5. Click the direcon arrow to control the camera.
7). Click up/down direcon buon to select the
item.
8). Click Iris + to conrm the selecon.
9). Click le/right direcon buon to adjust the
value of the selected item.
3.1 VIDEO FORMAT
You can select the video format as 1080p@25fps , or
1080p@30fps .
3.2 LANGUAGE
Supports English, and Chinese.
3.3 MAIN MENU
3.3.1 EXPOSURE
You are allowed to set BRIGHTNESS, EXPOSURE MODE ,
AGC DWDR, and .
COLOR GAIN
Adjust this feature to change the gain of the color. The
value ranges from 1 to 10.
DNR (Digital Noise Reducon)
The funcon can decrease the noise eect, DNR
especially when capturing moving images in poor light
condions, and delivering more accurate and sharper
image. You can set the lue from 1 to 9.DNR va
MIRROR
OFF H V, , , and HV are selectable for mirror.
OFF: The mirror funcon is disabled.
H: The image flips 180 horizontally.°
V: The image flips 180 vercally.°
HV: The image flips 180 both horizontally and °
vercally.
3.3.5 RESET
Reset all the setngs to the factory default.
3.3.6 SAVE & EXIT
Move the cursor to SAVE & EXIT , and click Iris+ to save
the setngs, and exit the menu.
UD10298B


Produktspezifikationen

Marke: Hikvision
Kategorie: Überwachungskamera
Modell: DS-2CE56D0T-ITME

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hikvision DS-2CE56D0T-ITME benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Überwachungskamera Hikvision

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-