Hikvision DS-2CE56C2T-VFIR3 Bedienungsanleitung

Hikvision Überwachungskamera DS-2CE56C2T-VFIR3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hikvision DS-2CE56C2T-VFIR3 (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
TVI Turret & Bullet Camera
User Manual
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to the following models.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
0100001040924
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology It features high resolution,.
low image distortion and low noise, etc , which.
makes it suitable for surveillance system and
image processing system.
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l OSD menu, parameters are configurable;
Support auto white balance, auto gain control,
l
electronic shutter control;
Support image effect adjustment;
l
l
Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
1 Introduction
1.1 Product Features
UD.6L0201D1611A01
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
Please refer to the product specification for
camera parameters and functions.
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
2 Installation
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
TURBO HD
1.2 Overview
1.2.1 Overview of Type I Camera
1.2.2 Overview of Type Camera
II
Figure 1-1 Overview of Type I Camera
Figure 1-2 Overview of Type CameraII
2.1 Installation of Type CameraI
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2 Push the lock button to disassemble the camera
.
from the mounting base.
Figure 2-2 Release The Lock Screw
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
3.Fix the mounting base to the ceiling.
Before you start:
Cameras in some models do not support OSD
menu. For actual operation, please refer to the
specification of each model.
Type
Model
I
II
DS-2CE56C2T-VFIR3
DS-2CE56D1T-VFIR3
DS-2CE16C2T-VFIR3
DS-2CE16D1T-VFIR3
Type
Type
4.Route the cables to the cable hole and connect
the corresponding cables.
5.Secure the camera to the mounting base by
supplied screws. Keep the word UP on the camera
being upright during the installation to make the
image showing normally.
Figure 2-4 Universal Adjustment
6.Adjust the camera according to the figure below
to get an optimum angle.
Figure 2-3 Secure the Camera
7.Use the screwdriver to adjust the ZOOM screw
and the FOCUS screw until you get the optimum
image.
Figure 2-5 Zoom and Focus Adjustment
2.2 Installation of Type II Camera
Both wall mounting and ceiling mounting are
suitable for type bullet camera. Ceiling mountingII
will be taken as an example in the section. And you
can take steps of ceiling mounting as a reference
if wall mounting is adopted.
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
Figure 2-6 Drill Template
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-7 Fix the Camera to the Ceiling
Figure 2-8 3-axis Adjustment
5. Adjust the surveillance angle.
1). Loosen No.1 adjusting screw to adjust the pan
position (0 ~ 360 ).° °
2).Tighten No.1 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(0 ~ 90 ).° °
4).Tighten No.2 adjusting screw.
5). Loosen No.3 adjusting screw to adjust the
rotation position 0 ~ 360 .( ° °)
6).Tighten No.3 adjusting screw.
0~360
0~360
1
2
3
0~90
3.2 DAY/NIGHT
Color, B/W, AUT O and EXT are selectable for DAY/
NIGHT switches. Under the mode of the AUT O and
EX T, you can set the I R LED as Smart and CDS. If the
IR LED is selected as Smart, you can set the bright-
ness of the IR LED.
3.3.3 AWB
Fi gure 3-2 DAY/NIGHT
Figure 3-3 AWB
SPECIAL
1. PRIVACY ZONE
2. MOTION
3. HLC
4. RETURN RET
Fi gure 3-4 SPECIAL
Motion: Set the Motion status as ON or O FF. Set
the SEN SI TI VI TY from 0 to 255. Set the alarm status
as ICO N/T RANC E/OF F. Set the hold time from
0 second to 255 seconds.
HLC: HLC supplements the brightness of the
peripheral area of the image. You can set the mask
value and threshold from 0 to 255.
Privacy zone: Select a PRI VACY area. Set the
MASK PAT as OFF, GRAY, WHI T E or BLAC K. Set the
SX/EX/SY/E Y value to define the position and size
of the area.
DAY/NIGHT
1. MODE AUTO
2. D TO N 63
3. N TO D 63
4. DELAY TIME 20
5. RETURN RET
AWB
1. MODE AUTO
2. R-G GAIN 255
3. B-G GAIN 151
4. RETURN RET
Auto, User, Push, 8000k, 6000k, 4200k and 3000k
are selectable for AWB. Under the mode of AUTO,
you need to set the R-G/B-G Gain and to select an
indoor/outdoor mode. If the AWB mode is select
as User, You need to set the R/G/B Gain manually.
3.3.4 AE
You can set the A E mode as H OL D, DC and E SC.
: Brightness refers to the brightnessBrightness
of the image.
: Shutter denotes the speed of the shutter.Shutter
You can set the shutter as AU TO, 1/25, 1/30, 1/50,
1/60, 1/100, 1/120, 1/250, 1/500, 1/1k, 1/3k and
1/10k.
: You can set the flicker status as 50H Z/60H ZFlicker
to prevent image flicking.
: BLC bases on the back area to enhance theBLC
brightness of the whole image. You can set the
BLC gain from 0 to 16.
: AGC optimizes the clarity of image in poorAGC
light scene. The value of AGC can be set from 1-5.
: LSC corrects the phenomenon where theLSC
image gets darkened or blurred on the periphery.
3.3.5 SPECIAL
SYSTEM
1. CAMERA ID 255
2. ID DISP. ON
3. NAME DISP. ON
4. LANGUAGE ENG
5. FACTORY INIT OFF
6. RETURN RET
3.3.7 SYSTEM
You can set the camera I D from 0 to 255.
Select the ID display and name display status as
ON/OF F.
Chinese and English are selectable for the language
of the menu.
You can restore the camera to the default by
setting the factory initialization status as ON.
3.3.8 EXI T
Exit and Save & exit are selectable.
EFFECT
1. COLOR GAIN 200
2. COLOR HUE 200
3. SHARPNESS 25
4. CONTRAST 150
5. BRIGHT OFF. 1
6. MIRROR ON
7. FLIP ON
8. RETURN RET
Color Gain: Color gain adjust this feature to change
the saturation of the color. You can set the value
from 0 to 255.
: You can adjust the image HUE fromColor Hue
0 to 71.
: Sharpness determines the amount ofSharpness
detail that an imaging system can reproduce.
You can set the value from 0 to 255.
: Contrast enhances the difference inContrast
color and light between parts of an image.
You can set the value from 0 to 255.
: Bright Off. refers to the brightnessBright Off.
compensation of the image. You can set the bright
compensation value as 0 or 1.
: You can set the Mirror status as O N/OF F.Mirror
: You can set the F LI P status as O N/O FF.Flip
3.3.6 EFFECT
Figure 3-5 EFFECT Figure 3-6 SYST EM
3 Menu Operation
Figure 3-1 Main Menu
Menu
AE
AWB
DAY&NIGHT SYSTEM
SPECIAL EFFECT
DC
ESC
HOLD
FRAME
RATE
AUTO
USER
HOLD
8000K
6000K
COLOR
B/W
AUTO
CAMERA
ID
ID DISP
PRIVACY
ZONE
MOTION
HLC
LANGUAGE
COLOR
GAIN
COLOR
HUE
SHARPNESS
EXIT
VIDEO. OUT
4200K
3200K
CONTRAST
BRIGHT
MIRROR
FLIP
NAME
DISP
FACTORY
INIT
EXT
PUSH
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
3.1 VIDEO.OUT
You can set the frame rate as 25 fps/30fps.
6.Push the focus &zoom adjustment cover upward
to move it aside.
7.Use the cover as a screwdriver to adjust the ZOOM
screw and the FOCUS screw until you get the
optimum image.
Cover
Cover
Cover
CoverCover
Focu
Focu
Focu
FocuFocus
s
s
ss
Zoom
Zoom
Zoom
ZoomZoom
0~360
Cover
Cover
Cover
CoverCover
Figure 2-9 Zoom and Focus Adjustment

Produktspezifikationen

Marke: Hikvision
Kategorie: Überwachungskamera
Modell: DS-2CE56C2T-VFIR3

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hikvision DS-2CE56C2T-VFIR3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Überwachungskamera Hikvision

Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE56C0T-IT3 Bedienungsanleitung

8 Oktober 2024
Hikvision

Hikvision iDS-TCV900-AI Bedienungsanleitung

3 Oktober 2024
Hikvision

Hikvision DS-2CE56C2T-IT3(3.6MM) Bedienungsanleitung

3 Oktober 2024
Hikvision

Hikvision iDS-2CD7A26G0/P-IZHS Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024
D-Link

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024
Foscam

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024
Alecto

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024
Friedland

Friedland E895 Bedienungsanleitung

10 Oktober 2024
Elro

Elro RM 140 Bedienungsanleitung

9 Oktober 2024
D-Link

D-Link DCS-5000L Bedienungsanleitung

9 Oktober 2024
Dahua Technology

Dahua Technology Ultra IPC-HF7842F Bedienungsanleitung

8 Oktober 2024
Lorex

Lorex E891AB Bedienungsanleitung

7 Oktober 2024
Overmax

Overmax Camspot 3.6 Bedienungsanleitung

6 Oktober 2024