Hikvision DS-2CD6424FWD-10 Bedienungsanleitung

Hikvision Überwachungskamera DS-2CD6424FWD-10

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hikvision DS-2CD6424FWD-10 (160 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 44 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/160

User Manual of Network Camera

User Manual

UD.6L0201D1674A02

Network Camera

User Manual of Network Camera

Thank you for purchasing our product. If there are any questions, or requests, please

do not hesitate to contact the dealer.

This manual applies to . Network Camera (V5.2.6)

This manual may contain several technical incorrect places or printing errors, and the

content is subject to change without notice. The updates will be added to the new

version of this manual. We will readily improve or update the products or procedures

described in the manual.

DISCLAIMER STATEMENT

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability

of the security or signaling aspects of this product. UL has only tested for ﬁre, shock

or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL

Certiﬁcation does not cover the performance or reliability of the security or signaling

aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR

RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS

OF THIS PRODUCT .”

User Manual of Network Camera

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and found to comply with the

limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may

cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are

marked with "CE" and comply therefore with the applicable

harmonized European standards listed under the Low Voltage

Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European

Union. For proper recycling, return this product to your local

supplier upon the purchase of equivalent new equipment, or dispose

of it at designated collection points. For more information see:

www.recyclethis.info.

2006/66/EC (battery directive): This product contains a battery that

cannot be disposed of as unsorted municipal waste in the European

Union. See the product documentation for speciﬁc battery

information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the battery to your supplier or to

a designated collection point. For more information see: www.recyclethis.info.

User Manual of Network Camera

Safety Instruction

These instructions are intended to ensure that the user can use the product correctly to

avoid danger or property loss.

The precaution measure is divided into ‘Warnings’ and ‘Cautions’:

Warnings: Serious injury or death may be caused if any of these warnings are

neglected.

Cautions: Injury or equipment damage may be caused if any of these cautions are

neglected.

Warnings Follow these safeguards to

prevent serious injury or death.

Cautions Follow these precautions to

prevent potential injury or material

damage.

Warnings:

 Please adopt the power adapter which can meet the safety extra low voltage

(SELV) standard. And source with 12 V or 24 VDC AC (depending on models)

according to the IEC60950-1 and Limited Power Source standard.

 If the product does not work properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the camera yourself. (We shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

 To reduce the risk of ﬁre or electrical shock, do not expose this product to rain or

moisture.

 This installation should be made by a qualiﬁed service person and should conform

to all the local codes.

 Please install blackouts equipment into the power supply circuit for convenient

supply interruption.

 Please make sure that the ceiling can support more than 50(N) Newton gravities if

the camera is ﬁxed to the ceiling.

 If the product does not work properly, please contact your dealer or the nearest

service center. Never attempt to disassemble the camera yourself. (We shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

User Manual of Network Camera

Cautions:

 Make sure the power supply voltage is correct before using the camera.

 Do not drop the camera or subject it to physical shock.

 Do not touch sensor modules with ﬁngers. If cleaning is necessary, use a clean

cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an

extended period of time, put on the lens cap to protect the sensor from dirt.

 Do not aim the camera lens at the strong light such as sun or incandescent lamp.

The strong light can cause fatal damage to the camera.

 The sensor may be burned out by a laser beam, so when any laser equipment is

being used, make sure that the surface of the sensor not be exposed to the laser

beam.

 Do not place the camera in extremely hot, cold temperatures (the operating

temperature should be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera

model has an “H” in its suffix), dusty or damp environment, and do not expose it

to high electromagnetic radiation.

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep the camera away from water and any liquid.

 While shipping, the camera should be packed in its original packing.

 Improper use or replacement of the battery may result in hazard of explosion.

Please use the manufacturer recommended battery type.

Notes:

For the camera supports IR, you are required to pay attention to the following

precautions to prevent IR reﬂection:

 Dust or grease on the dome cover will cause IR reﬂection. Please do not remove

the dome cover ﬁlm until the installation is ﬁnished. If there is dust or grease on

the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.

 Make certain the installation location does not have reﬂective surfaces of objects

too close to the camera. The IR light from the camera may reﬂect back into the

lens causing reﬂection.

 The foam ring around the lens must be seated ﬂush against the inner surface of

the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera

body so that the foam ring and the dome cover are attached seamlessly.

User Manual of Network Camera

Table of Contents

Chapter 1 System Requirement ................................................................................ 8

Chapter 2 Network Connection ................................................................................ 9

2.1 Setting the Network Camera over the LAN......................................................... 9

2.1.1 Wiring over the LAN ........................................................................................................ 9

2.1.2 Detecting and Changing the IP Address .........................................................................10

2.2 Setting the Network Camera over the WAN ....................................................... 11

2.2.1 Static IP Connection ....................................................................................................... 11

2.2.2 Dynamic IP Connection .................................................................................................. 12

Chapter 3 Access to the Network Camera ............................................................. 15

3.1 Accessing by Web Browsers ................................................................................ 15

3.2 Accessing by Client Software .............................................................................. 17

Chapter 4 -Fi Settings ......................................................................................... 19 Wi

4.1 Conﬁguring Wi-Fi Connection in Manage and Ad-hoc Modes ....................... 19

4.2 Easy Wi-Fi Connection with WPS function ....................................................... 23

4.3 IP Property Settings for Wireless Network Connection ................................... 26

Chapter 5 Live View................................................................................................. 27

5.1 Live View Page ..................................................................................................... 27

5.2 Starting Live View ................................................................................................ 28

5.3 Recording and Capturing Pictures Manually ................................................... 29

5.4 Operating PTZ Control ....................................................................................... 29

5.4.1 PTZ Control Panel .......................................................................................................... 29

5.4.2 Setting / Calling a Preset . ................................................................................................ 30

5.4.3 Setting / Calling a Patrol ................................................................................................. 32

Chapter 6 Network Camera Conﬁguration ........................................................... 33

6.1 Conﬁguring Local Parameters............................................................................ 33

6.2 Conﬁguring Time Settings .................................................................................. 35

6.3 Conﬁguring Network Settings ............................................................................ 37

6.3.1 Conﬁguring TCP/IP Settings .......................................................................................... 37

6.3.2 Conﬁguring Port Settings ............................................................................................... 38

6.3.3 Conﬁguring PPPoE Settings ........................................................................................... 39

6.3.4 Conﬁguring DDNS Settings ........................................................................................... 39

6.3.5 Conﬁguring SNMP Settings ........................................................................................... 43

6.3.6 Conﬁguring 802.1X Settings .......................................................................................... 44

User Manual of Network Camera

6.3.7 Conﬁguring QoS Settings ............................................................................................... 45

6.3.8 Configuring UPnP™ Settings......................................................................................... 46

6.3.9 Conﬁguring Wireless Dial Settings ................................................................................ 47

6.3.10 Email Sending Triggered by Alarm ................................................................................ 50

6.3.11 Conﬁguring NAT (Network Address Translation) Settings ............................................ 52

6.3.12 Conﬁguring FTP Settings ............................................................................................... 52

6.3.13 Platform Access .............................................................................................................. 54

6.3.14 HTTPS Settings .............................................................................................................. 54

6.4 Conﬁguring Video and Audio Settings ............................................................... 56

6.4.1 Conﬁguring Video Settings ............................................................................................56

6.4.2 Conﬁguring Audio Settings ............................................................................................ 58

6.4.3 Conﬁguring ROI Encoding ............................................................................................. 59

6.4.4 Display Information on Stream ....................................................................................... 61

6.4.5 Conﬁguring Target Cropping .......................................................................................... 62

6.5 Conﬁguring Image Parameters .......................................................................... 63

6.5.1 Conﬁguring Display Settings .........................................................................................63

6.5.2 Conﬁguring OSD Settings .............................................................................................. 68

6.5.3 Conﬁguring Text Overlay Settings ................................................................................. 70

6.5.4 Conﬁguring Privacy Mask .............................................................................................. 71

6.5.5 Conﬁguring Picture Overlay ........................................................................................... 72

6.6 Conﬁguring and Handling Alarms ..................................................................... 73

6.6.1 Conﬁguring Motion Detection ........................................................................................73

6.6.2 Conﬁguring Video Tampering Alarm ............................................................................. 79

6.6.3 Conﬁguring Alarm Input ................................................................................................ 80

6.6.4 Conﬁguring Alarm Output .............................................................................................. 81

6.6.5 Handling Exception ........................................................................................................ 82

6.6.6 Conﬁguring Other Alarm ................................................................................................ 83

6.6.7 Conﬁguring Audio Exception Detection ........................................................................86

6.6.8 Conﬁguring Defocus Detection ...................................................................................... 87

6.6.9 Conﬁguring Scene Change Detection ............................................................................. 88

6.6.10 Conﬁguring Face Detection ............................................................................................ 89

6.6.11 Conﬁguring Line Crossing Detection ............................................................................. 90

6.6.12 Conﬁguring Intrusion Detection ..................................................................................... 92

6.6.13 Conﬁguring Region Entrance Detection ......................................................................... 94

6.6.14 Conﬁguring Region Exiting Detection ........................................................................... 95

6.6.15 Conﬁguring Loitering Detection ....................................................................................96

6.6.16 Conﬁguring People Gathering Detection ........................................................................98

6.6.17 Conﬁguring Fast Moving Detection ............................................................................... 99

6.6.18 Conﬁguring Parking Detection ..................................................................................... 101

6.6.19 Conﬁguring Unattended Baggage Detection ................................................................ 102

6.6.20 Conﬁguring Object Removal Detection ....................................................................... 104

User Manual of Network Camera

6.7 VCA Conﬁguration ............................................................................................ 106

6.7.1 Behavior Analysis ......................................................................................................... 106

6.7.2 Face Capture ................................................................................................................. 112

6.7.3 Heat Map ...................................................................................................................... 116

6.7.4 People Counting 118 ...........................................................................................................

Chapter 7 Storage Settings .................................................................................... 122

7.1 Conﬁguring NAS Settings ................................................................................. 122

7.2 Conﬁguring Recording Schedule ...................................................................... 124

7.3 Conﬁguring Snapshot Settings ......................................................................... 128

7.4 Conﬁguring Lite Storage ................................................................................... 130

7.5 Conﬁguring Cloud Storage ............................................................................... 131

Chapter 8 People Counting ................................................................................... 133

Chapter 9 Road Traﬀic .......................................................................................... 136

Chapter 10 Playback ............................................................................................ 140

Chapter 11 Log Searching ................................................................................... 142

Chapter 12 Others ................................................................................................ 143

12.1 Managing User Accounts ................................................................................... 143

12.2 Authentication .................................................................................................... 146

12.3 Anonymous Visit ................................................................................................ 147

12.4 IP Address Filter ................................................................................................. 148

12.5 Security Service .................................................................................................. 149

12.6 Viewing Device Information .............................................................................. 150

12.7 Maintenance ....................................................................................................... 151

12.7.1 Rebooting the Camera .................................................................................................. 151

12.7.2 Restoring Default Settings ............................................................................................ 151

12.7.3 Exporting / Importing Conﬁguration File ..................................................................... 151

12.7.4 Upgrading the System ................................................................................................... 152

12.8 -232 Settings ................................................................................................... 153 RS

12.9 -485 Settings ................................................................................................... 153 RS

12.10 Service Settings ................................................................................................... 154

Appendix ................................................................................................................... 155

Appendix 1 SADP Software Introduction ..................................................................... 155

Appendix 2 Port Mapping .............................................................................................. 158

User Manual of Network Camera

Chapter 1 System Requirement

Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /

Server 2003 / Server 2008 32bits

CPU: Intel Pentium IV 3.0 Core i7-4000 series or higher, depending on GHz to

different video resolutions

RAM: 1G or higher

Display: 1024×768 resolution or higher

Web Browser: Internet Explorer 7.0 and above version, Safari 5.02 and above

version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above

versions.

User Manual of Network Camera

Chapter 2 Network Connection

Before you start:

 If you want to set the network camera via LAN (Local Area Network), please a

refer to Section 2.1 Setting the Network Camera over the LAN.

 If you want to set the network c era via WAN (Wide Area Network), please am a

refer to Section 2.2 Setting the Network Camera over the WAN.

2.1 Setting the Network Camera over the LAN

Purpose:

To view and conﬁgure the camera via LAN, you need to connect the network a

camera in the same subnet with your computer, and install the SADP or iVMS-4200

software to search and change the IP of the network camera.

Note: For the detailed introduction of SADP, please refer to Appendix 1.

2.1.1 Wiring over the LAN

The following ﬁgures show the two ways of cable connection of network camera a

and computer: a

Purpose:

 To test the network camera, you can directly connect the network camera to the

computer with a network cable as shown in Figure 2-1.

 Refer to the Figure 2-2 to set network camera over the LAN via a switch or a

router.

Figure 2-1 Connecting Directly

User Manual of Network Camera

for the network camera after you logged in. For detailed information, please refer

to Section 6.3.1 Conﬁguring TCP/IP Settings.

Figure 2-3 SADP Interface

2.2 Setting the Network Camera over the WAN

Purpose:

This section explains how to connect the network camera to the WAN with a static IP

or a dynamic IP.

2.2.1 Static IP Connection

Before you start:

Please apply a static IP from an ISP (Internet Service Provider). With the static IP

address, you can connect the network camera via a router or connect it to the WAN

directly.

 Connecting the network camera via a router

User Manual of Network Camera

Steps:

1. Connect the network camera to the router.

2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2

Detecting and Changing the IP Address for detailed IP address conﬁguration of

the camera.

3. Save the static IP in the router.

4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port mapping vary

according to the diﬀerent routers. Please call the router manufacturer for

assistance with port mapping.

Note: Refer to Appendix 2 for detailed information about port mapping.

5. Visit the network camera through a web browser or the client software over the

internet.

Figure 2-4 Accessing the Camera through Router with Static IP

 Connecting the network camera with static IP directly

You can also save the static IP in the camera and directly connect it to the internet

without using a router. Refer to Section 2.1.2 Detecting and Changing the IP Address

for detailed IP address conﬁguration of the camera.

Figure 2-5 Accessing the Camera with Static IP Directly

2.2.2 Dynamic IP Connection

Before you start:

Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect

the network camera a modem or a router. to

User Manual of Network Camera

 Connecting the network camera via a router

Steps:

1. Connect the network camera to the router.

2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer

to Section 2.1.2 Detecting and Changing the IP Address for detailed LAN

conﬁguration.

3. In the router, set the PPPoE user name, password and conﬁrm the password.

4. Set port mapping. E.g. 80, 8000, and 554 ports. The steps for port mapping vary

depending on diﬀerent routers. Please call the router manufacturer for assistance

with port mapping.

Note: Refer to Appendix 2 for detailed information about port mapping.

5. Apply a domain name from a domain name provider.

6. Conﬁgure the DDNS settings in the setting interface of the router.

7. Visit the camera via the applied domain name.

 Connecting the network camera via a modem

Purpose:

This camera supports the PPPoE auto dial-up function. The camera gets a public IP

address by ADSL dial-up after the camera is connected to a modem. You need to

conﬁgure the PPPoE parameters of the network camera. Refer to Section 6.3.3

Conﬁguring PPPoE Settings for detailed conﬁguration.

Figure 2-6 Accessing the Camera with Dynamic IP

Note: The obtained IP address is dynamically assigned via PPPoE, so the IP address

always changes after rebooting the camera. To solve the inconvenience of the

dynamic IP, you need to get a domain name from the DDNS provider (E.g.

DynDns.com). Please follow the steps below for normal domain name resolution and

private domain name resolution to solve the problem.

User Manual of Network Camera

 Normal Domain Name Resolution

Figure 2-7 Normal Domain Name Resolution

Steps:

1. Apply a domain name from a domain name provider.

2. Conﬁgure the DDNS settings in the DDNS Settings interface of the network

camera. Refer to for detailed Section 6.3.4 Conﬁguring DDNS Settings

conﬁguration.

3. Visit the camera via the applied domain name.

 Private Domain Name Resolution

Figure 2-8 Private Domain Name Resolution

Steps:

1. Install and run the IP Server software in a computer with a static IP.

2. Access the network camera through the LAN with web browser or the client a

software.

3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4

Conﬁguring DDNS Settings for detailed conﬁguration.

User Manual of Network Camera

Chapter 3 Access to the Network

Camera

3.1 Accessing by Web Browsers

Steps:

1. Open the web browser.

2. Input the IP address of the network camera in the address bar, e.g., 192.0.0.64 and

press the key to enter the login interfa . Enter ce

3. Input the user name and password and click . Login

Figure 3-1 Login Interface

Notes :

 The default user name is , and the default password is . admin 12345

 This product has default user name and password credentials for ﬁrst time access.

You must change these default credentials to protect against unauthorized access

to the product. For details, please refer to . Section 12.1 Managing User Accounts

4. Install the plug-in before viewing the live video and operating the camera. Please

follow the installation prompts to install the plug- . in

User Manual of Network Camera

Figure 3-2 Download and Install Plug- in

Figure 3-3 Install Plug-in (1)

Figure 3-4 Install Plug-in (2)

Note: You may have to close the web browser to install the plug-in. Please reopen the

web browser and log in again after installing the plug-in.

User Manual of Network Camera

3.2 Accessing by Client Software

The product CD contains the iVMS-4200 client software. You can view the live video

and manage the camera with the software.

Follow the installation prompts to install the software. The control panel and live view

interface of iVMS-4200 client software are shown as bellow.

Figure 3-5 iVMS-4200 Control Panel

User Manual of Network Camera

Figure 3-6 iVMS-4200 Main View

Note: For detailed information about the software, please refer to the user manual of

the iVMS-4200.

User Manual of Network Camera

Chapter 4 -Fi Settings Wi

Purpose:

By connecting to the wireless network, you don’t need to use cable of any kind for

network connection, which is very convenient for the actual surveillance application.

Note: This chapter is only applicable for the cameras with the built-in -Fi module.Wi

4.1 Conﬁguring Wi-Fi Connection in Manage and

Ad-hoc Modes

Before you start:

A wireless network must be conﬁgured.

Wireless Connection in Manage Mode

Steps:

1. Enter the Wi-Fi conﬁguration interface.

Conﬁguration> Advanced Conﬁguration> Network> Wi- Fi

Figure 4-1 Wireless Network List

2. Click Search to search the online wireless connections.

3. Click to choose a wireless connection on the list.

Figure 4-2 -Fi Setting- Manage Mode Wi

User Manual of Network Camera

4. Check the checkbox to select the and the Network mode as Manage, Security

mode of the network is automatically shown when you select the wireless

network, please don’t change it manually.

Note: These parameters are exactly identical with those of the router.

5. Enter the key to connect the wireless network. The key should be that of the

wireless network connection you set on the router.

Wireless Connection in Ad-hoc Mode

If you choose the Ad-hoc mode, you don’t need to connect the wireless camera via a

router. The scenario is the same as you connect the camera and the PC directly with a

network cable.

Steps:

1. Choose Ad-hoc mode.

Figure 4-3 -Fi Setting- Wi Ad-hoc

2. Customize a SSID for the camera.

3. Choose the Security Mode of the wireless connection.

Figure 4-4 Security Mode- Ad-hoc Mode

4. Enable the wireless connection function for your PC.

5. On the PC side, search the network and you can see the SSID of the camera

listed.

User Manual of Network Camera

Figure 4-5 -hoc Connection Point Ad

6. Choose the SSID and connect.

Security Mode Description:

Figure 4-6 Security Mode

You can choose the Security Mode as not-encrypted, WEP, WPA-personal,

WPA-enterprise, WPA2-personal, and WPA2-enterprise.

WEP mode:

Figure 4-7 WEP Mode

 Authentication - Select Open or Shared Key System Authentication, depending on

User Manual of Network Camera

the method used by your access point. Not all access points have this option, in

which case they probably use Open System, which is sometimes known as SSID

Authentication.

 Key length - This sets the length of the key used for the wireless encryption, 64 or

128 bit. The encryption key length can sometimes be shown as 40/64 and

104/128.

 Key type - The key types available depend on the access point being used. The

following options are available:

HEX - Allows you to manually enter the hex key.

ASCII - In this method the string must be exactly 5 characters for 64-bit WEP

and 13 characters for 128-bit WEP.

WPA-personal and WPA2-personal Mode:

Enter the required Pre-shared Key for the access point, which can be a hexadecimal

number or a passphrase.

Figure 4-8 Security Mode- WPA-personal

WPA- enterprise and WPA2-enterprise Mode:

Choose the type of client/server authentication being used by the access point;

EAP-TLS or EAP-PEAP.

EAP-TLS

User Manual of Network Camera

Figure 4-9 EAP-TLS

 Identity - Enter the user ID to present to the network.

 Private key password Enter the password for your user ID. –

 EAPOL version - Select the version used (1 or 2) in your access point.

 CA Certiﬁcates - Upload a CA certiﬁcate to present to the access point for

authentication.

EAP-PEAP:

 User Name - Enter the user name to present to the network

 Password - Enter the password of the network

 PEAP Version - Select the PEAP version used at the access point.

 Label - Select the label used by the access point.

 EAPOL version - Select version (1 or 2) depending on the version used at the

access point

 CA Certiﬁcates - Upload a CA certiﬁcate to present to the access point for

authentication

4.2 Easy Wi-Fi Connection with WPS function

Purpose:

The setting of the wireless network connection is never easy. To avoid the complex

setting of the wireless connection you can enable the WPS function.

User Manual of Network Camera

WPS (Wi-Fi Protected Setup) refers to the easy conﬁguration of the encrypted

connection between the device and the wireless router. The WPS makes it easy to add

new devices to an existing network without entering long passphrases. There are two

modes of the WPS connection, the PBC mode and the PIN mode.

Note: If you enable the WPS function, you do not need to conﬁgure the parameters

such as the encryption type and you don’t need to know the key of the wireless

connection.

Steps:

Figure 4-10 -Fi Settings - WPS Wi

PBC Mode:

PBC refers to the Push-Button-Conﬁguration, in which the user simply has to push a

button, either an actual or virtual one (as the button on the conﬁguration

interface of the IE browser), on both the Access Point (and a registrar of the network)

and the new wireless client device.

1. Check the checkbox of to enable WPS.

2. Choose the connection mode as PBC.

Note: Support of this mode is mandatory for both the Access Points and the

connecting devices.

3. Check on the Wi-Fi router to see if there is a WPS button. If yes push the button

and you can see the indicator near the button start ﬂashing, which means the WPS

function of the router is enabled. For detailed operation, please see the user guide of

the router.

User Manual of Network Camera

4. Push the WPS button to enable the function on the camera.

If there is not a WPS button on the camera, you can also click the virtual button to

enable the PBC function on the web interface.

5. Click button. Connect

When the PBC mode is both enabled in the router and the camera, the camera and the

wireless network is connected automatically.

PIN Mode:

The PIN mode requires a Personal Identiﬁcation Number (PIN) to be read from either

a sticker or the display on the new wireless device. This PIN must then be entered to

connect the network, usually the Access Point of the network.

Steps:

1. Choose a wireless connection on the list and the SSID is shown.

Figure 4-11 -Fi Settings WPS PIN Mode Wi –

2. Choose Use route PIN code.

If the PIN code is generated from the router side, you should enter the PIN code you

get from the router side in the Router PIN code ﬁeld.

User Manual of Network Camera

3. Click . Connect

You can generate the PIN code on the camera side. And the expired time for the PIN

code is 120 seconds.

1. Click . Generate

2. Enter the code to the router, in the example, enter 48167581 to the router.

4.3 IP Property Settings for Wireless Network

Connection

The default IP address of wireless network interface controller is 192.168.1.64. When

you connect the wireless network you can change the default IP.

Steps:

1. Enter the TCP/IP conﬁguration interface.

Conﬁguration> Advanced Conﬁguration> Network> TCP/IP

Conﬁguration> Basic Conﬁguration> Network> TCP/IP

Figure 4-12 TCP/IP Settings

2. Select the NIC as wlan.

3. Customize the IPv4 address, the IPv4 Subnet Mask and the Default Gateway.

The setting procedure is the same with that of LAN.

If you want to be assigned the IP address you can check the checkbox to enable the

DHCP.

User Manual of Network Camera

Display Control:

Click each tab to adjust the layout and the stream type of the live vi . And you can ew

click the drop-down to select the plug-in. For IE (internet explorer) user,

webcomponents and quick time are selectable. And for Non-IE user, webcomponents,

quick time, VLC or MJPEG is selectable if they are supported by the web browser.

Live View Window:

Display the live video.

Toolbar:

Operations on the live view page, e.g., live view, capture, record, audio on/oﬀ,

two-way audio, etc.

PTZ Control:

Panning, tilting and zooming actions of the camera and the light and wiper control.

(only available for cameras supporting PTZ function)

Preset/Patrol Settings :

Set/call/delete the presets or patrols for PTZ cameras.

5.2 Starting Live View

In the live view window as shown in Figure 5-2, click on the toolbar to start the

live view of the camera.

Figure 5-2 Live View Toolbar

Table 5-1 Descriptions of the Toolbar

Icon

Description

Start/Stop live view.

The window size is 4:3.

The window size is 16:9.

The origin widow size. al

Self-adaptive window size.

Live view with the main stream.

Live view with the sub stream.

Live view with the third stream.

User Manual of Network Camera

Click the direction buttons to control the pan/tilt movements.

Figure 5-3 PTZ Control Panel

Click the zoom/iris/focus buttons to realize lens control.

Notes:

 There are 8 direction arrows ( , , , , , , , ) in the live view window

when you click and drag the mouse in the relative positions.

 For the cameras which support lens movements only, the direction buttons are

invalid.

Table 5-2 Descriptions of PTZ Control Panel

Icon

Description

Zoom in/out

Focus near/far

Iris / + -

Light on/off

Wiper on/off

Auxiliary focus

Initialize lens

Adjust speed of pan/tilt movements

5.4.2 Setting / Calling a Preset

 Setting a Preset:

1. In the PTZ control panel, select a preset number from the preset list.

User Manual of Network Camera

Figure 5-4 Setting a Preset

2. Use the PTZ control buttons to move the lens the desired position. to

• Pan the camera to the right or left.

• Tilt the camera up or down.

• Zoom in or out.

• Refocus the lens.

3. Click to ﬁnish the setting of the current preset.

4. You can click to delete the preset.

Note: You can conﬁgure up to 256 presets.

 Calling a Preset:

This feature enables the camera to point to a speciﬁed preset scene manually or when

an event takes place.

For the deﬁned preset, you can call it at any time to the desired preset scene.

In the PTZ control panel, select a deﬁned preset from the list and click to call the

preset.

Or you can place the mouse on the presets interface, and call the preset by typing the

preset No. to call the corresponding presets.

Figure 5-5 Calling a Preset

User Manual of Network Camera

5.4.3 Setting / Calling a Patrol

Note:

No less than 2 presets have to be conﬁgured before you set a patrol.

Steps:

1. C k to enter the patrol conﬁguration interface. lic

2. Select a path No., and click to add the conﬁgured presets.

3. Select the preset, and input the patrol duration and patrol speed.

4. Click OK to save the ﬁrst preset.

5. Follow the steps above to add the other presets.

Figure 5-6 Add Patrol Path

6. Click to save a patrol.

7. Click to start the patrol, and click to stop it.

8. (Optional) Click to delete a patrol.

User Manual of Network Camera

Chapter 6 Network Camera

Conﬁguration

6.1 Conﬁguring Local Parameters

Note: The local conﬁguration refers to the parameters of the live view, record ﬁles

and captured pictures. The record ﬁles and captured pictures are the ones you record

and captured using the web browser and thus the saving paths of them are on the PC

running the browser.

Steps:

1. Enter the Local Conﬁguration interface:

Conﬁguration > Local Conﬁguration

Figure 6-1 Local Conﬁguration Interface

2. Conﬁgure the following settings:

 Live View Parameters: Set the protocol type and live view performance.

 Protocol Type: TCP, UDP, MULTICAST and HTTP are selectable.

TCP: Ensures complete delivery of streaming data and better video quality,

yet the real-time transmission will be affected.

User Manual of Network Camera

UDP: Provides real-time audio and video streams.

HTTP: Allows the same quality as of TCP without setting speciﬁc ports for

streaming under some network environments.

MULTICAST: It’s recommended to select MCAST type when using the

Multicast function. For detailed information about Multicast, refer to Section

6.3.1 Conﬁguring TCP/IP Settings.

 Live View Performance: Set the live view performance to Shortest Delay or

Auto.

 Rules: It refers to the rules on your local browser, select enable or disable to

display or not display the colored marks when the motion detection, face

detection, or intrusion detection is triggered. E.g.: enabled as the rules are, and

the face detection is enabled as well, when a face is detected, it will be marked

with a green rectangle on the live view.

 Image Format: Choose the image format for picture capture.

 Record File Settings: Set the saving path of the recorded video ﬁles. Valid for the

record ﬁles you recorded with the web browser.

 Record File Size: Select the packed size of the manually recorded and

downloaded video ﬁles to 256M, 512M or 1G. After the selection, the

maximum record ﬁle size is the value you selected.

 Save record ﬁles to: Set the saving path for the manually recorded video ﬁles.

 Save downloaded ﬁles to: Set the saving path for the downloaded video ﬁles

in playback mode.

 Picture and Clip Settings: Set the saving paths of the captured pictures and

clipped video ﬁles. Valid for the pictures you captured with the web browser.

 Save snapshots in live view to: Set the saving path of the manually captured

pictures in live view mode.

 Save snapshots when playback to: Set the saving path of the captured

pictures in playback mode.

 Save clips to: Set the saving path of the clipped video ﬁles in playback mode.

Note: You can click to change the directory for saving the clips and pictures. Browse

User Manual of Network Camera

Figure 6-3 Time Sync by NTP Server

Note: If the camera is connected to a public network, you should use a NTP server

that has a time synchronization function, such as the server at the National Time

Center (IP Address: 210.72.145.44). If the camera is set in a customized network,

NTP software can be used to establish a NTP server for time synchronization.

 Synchronizing Time Synchronization Manually

Enable the Manual Time Sync function and then click to set the system time

from the pop-up calendar.

Note: You can also check the Sync with computer time checkbox to synchronize the

time of the camera with that of your computer.

Figure 6-4 Time Sync Manually

 Click the tab page to enable the DST function and Set the date of the DST DST

period.

Figure 6-5 DST Settings

2. Click to save the settings. Save

User Manual of Network Camera

6.3 Conﬁguring Network Settings

6.3.1 Conﬁguring TCP/IP Settings

Purpose:

TCP/IP settings must be properly conﬁgured before you operate the camera over

network. The camera supports both the IPv4 and IPv6. Both versions may be

conﬁgured simultaneously without conﬂicting to each other, and at least one IP

version should be conﬁgured.

Steps:

1. Enter TCP/IP Settings interface:

Conﬁguration > Basic Conﬁguration > Network > TCP/IP

Or Conﬁguration > Advanced Conﬁguration > Network > TCP/IP

Figure 6-6 TCP/IP Settings

2. Conﬁgure the basic network settings, including the NIC Type, IPv4 or IPv6

Address, IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings

User Manual of Network Camera

RTSP Port: The default port number is 554 and it can be changed to any port No.

ranges from 1024 to 65535.

HTTPS Port: The default port number is 443, and can be changed to any port it

No. which is not occupied.

Server Port: The default server port number is 8000, and it can be changed to

any port No. ranges from 2000 to 65535.

3. Click to save the settings. Save

Note: A reboot is required for the settings to take eﬀect.

6.3.3 Conﬁguring PPPoE Settings

Steps:

1. Enter the PPPoE Settings interface:

Conﬁguration >Advanced Conﬁguration > Network > PPPoE

Figure 6-8 PPPoE Settings

2. Check the checkbox to enable this feature. Enable PPPoE

3. Enter , , and password for PPPoE access. User Name Password Conﬁrm

Note: The User Name and Password should be assigned by your ISP.

4. Click to save and exit the interface. Save

Note: A reboot is required for the settings to take eﬀect.

6.3.4 Conﬁguring DDNS Settings

Purpose:

If your camera is set to use PPPoE as its default network connection, you can use the

Dynamic DNS (DDNS) for network access.

User Manual of Network Camera

Figure 6-10 DynDNS Settings



 IP Server:

Steps:

(1) Enter the Server Address of the IP Server.

(2) Click to save the settings. Save

Note: For the IP Server, you have to apply a static IP, subnet mask, gateway and

preferred DNS from the ISP. The should be entered with the Server Address

static IP address of the computer that runs the IP Server software.

Figure 6-11 IPServer Settings

Note: For the US and Canada area, you can enter 173.200.91.74 as the server

address.



 NO- : IP

Steps:

(1) Choose the DDNS Type as - . NO IP

User Manual of Network Camera

Figure 6-12 -IP Settings NO

(2) Enter the Server Address as www.noip.com

(3) Enter the Domain name you registered.

(4) Enter the Port number, if needed.

(5) Enter the User Name and Password.

(6) Click and then you can view the camera with the domain name. Save



 HiDDNS

Steps:

(1) Choose the DDNS Type as HiDDNS.

Figure 6-13 HiDDNS Settings

(2) Enter the Server Address www.hiddns.com

(3) Enter the Domain name of the camera. The domain is the same with the

device alias in the HiDDNS server.

(4) Click to save the new settings. Save

Note: A reboot is required for the settings to take effect.

User Manual of Network Camera

6.3.5 Conﬁguring SNMP Settings

Purpose:

You can set the SNMP function to get camera status, parameters and alarm related

information and manage the camera remotely when it is connected to the network.

Before you start:

Before setting the SNMP, please download the SNMP software and manage to

receive the camera information via SNMP port. By setting the Trap Address, the

camera can send the alarm event and exception messages to the surveillance center.

Note: The SNMP version you select should be the same as that of the SNMP software.

And you also need to use the diﬀerent version according to the security level you

required. SNMP v1 provides no security and SNMP v2 requires password for access.

And SNMP v3 provides encryption and if you use the third version, HTTPS protocol

must be enabled.

Steps:

1. Enter the SNMP Settings interface:

Conﬁguration > Advanced Conﬁguration > Network > SNMP

User Manual of Network Camera

1. Enter the QoS Settings interface:

Conﬁguration >Advanced Conﬁguration > Network > QoS

Figure 6-16 QoS Settings

2. Conﬁgure the QoS settings, including video / audio DSCP, event / alarm DSCP

and Management DSCP.

The valid value range of the DSCP is 0-63. The bigger the DSCP value is, the

higher the priority is.

Note: DSCP refers to the Differentiated Service Code Point; and the DSCP value

is used in the IP header to indicate the priority of the data.

3. Click to save the settings. Save

Note: A reboot is required for the settings to take eﬀect.

6.3.8 Configuring UPnP™ Settings

Universal Plug and Play (UPnP™) is a networking architecture that provides

compatibility among networking equipment, software and other hardware devices.

The UPnP protocol allows devices to connect seamlessly and to simplify the

implementation of networks in the home and corporate environments.

With the function enabled, you don’t need to configure the port mapping for each port,

and the camera is connected to the Wide Area Network via the router.

Steps:

1. Enter the UPnP™ settings interface.

Conﬁguration >Advanced Conﬁguration > Network > UPnP

2. Check the checkbox to enable the UPnP™ function.

The name of the device when detected online can be edited.

User Manual of Network Camera

5) Click to save the settings. Save

6.3.10 Email Sending Triggered by Ala rm

Purpose:

The system can be conﬁgured to send an Email notiﬁcation to all designated receivers

if an alarm event is detected, e.g., motion detection event, video loss, video tampering,

etc.

Before you start:

Please conﬁgure the DNS Server settings under Basic Conﬁguration > Network >

TCP/IP Advanced Conﬁguration > Network > TCP/IPor before using the Email

function.

Steps:

1. Enter the TCP/IP Settings (Conﬁguration > Basic Conﬁguration > Network >

TCP/IP Conﬁguration > Advanced Conﬁguration > Network > TCP/IP) or to

set the IPv4 Address, IPv4 Subnet Mask, IPv4 Default Gateway and the Preferred

DNS Server.

Note: Please refer to for detailed Conﬁguring TCP/IP SettingsSection 6.3.1

information.

2. Enter the Email Settings interface:

Conﬁguration > Advanced Configuration > Network > Email

User Manual of Network Camera

Figure 6-22 Email Settings

3. Conﬁgure the following settings:

Sender: The name of the email sender.

Sender’s Address: The email address of the sender.

SMTP Server: The SMTP Server IP address or host name (e.g.,

smtp.263xmail.com).

SMTP Port: The SMTP port. The default TCP/IP port for SMTP is 25 (not

secured). And the SSL SMTP port is 465.

Enable SSL: Check the checkbox to enable SSL if it is required by the SMTP

server.

Attached Image: Check the checkbox of Attached Image if you want to send

emails with attached alarm images.

Interval: The interval refers to the time between two actions of sending attached

pictures.

Authentication (optional): If your email server requires authentication, check

this checkbox to use authentication to log in to this server and enter the login user

Produktspezifikationen

Marke:	Hikvision
Kategorie:	Überwachungskamera
Modell:	DS-2CD6424FWD-10

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hikvision DS-2CD6424FWD-10 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Überwachungskamera Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2CE56C0T-IT3 Bedienungsanleitung

8 Oktober 2024

Hikvision iDS-TCV900-AI Bedienungsanleitung

3 Oktober 2024

Hikvision DS-2CE56C2T-IT3(3.6MM) Bedienungsanleitung

3 Oktober 2024

Hikvision iDS-2CD7A26G0/P-IZHS Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024

Friedland E895 Bedienungsanleitung

10 Oktober 2024

Elro RM 140 Bedienungsanleitung

9 Oktober 2024

D-Link DCS-5000L Bedienungsanleitung

9 Oktober 2024

Dahua Technology Ultra IPC-HF7842F Bedienungsanleitung

8 Oktober 2024

Lorex E891AB Bedienungsanleitung

7 Oktober 2024

Overmax Camspot 3.6 Bedienungsanleitung

6 Oktober 2024