HELGI HLGOMN36BLWH Bedienungsanleitung

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr HELGI HLGOMN36BLWH (2 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
HELGI Europe Via Artigiani 29/31 29020 Vigolzone (PC) Italy
E-mail education@helgi-solution.com Web helgi-solutions.com
Programmazione Timer
Timer operation manual
Attenzione: tutte le operazioni descritte di seguito dovranno essere
eseguite in modalità POWER OFF. Portare l’interruttore [E] su OFF.
Impostare l’alimentazione simultanea di tutte le prese
1. Premere SET [C]. Sul display [F] comparirĂ  la scritta ON.
2. Premere SET [C]. Premere [A] per aumentare il minutaggio, [B] per diminuirlo. Impo-
stando il valore “000” le prese saranno sempre attive.
3. Premere SET [C] per salvare le impostazioni e ON [D] per attivare la ricarica. Tutti i
LED corrispondenti alle diverse strisce di alimentazione [G] si accenderanno e reste-
ranno in tensione per la durata impostata al punto 2.
4. Portare l’interruttore [E] su ON per avviare la ricarica. Sul display [F] verranno mostrati
i minuti restanti al completamento della ricarica.
Impostare l’alimentazione ciclica su gruppi di prese
1. Premere SET [C]. Sul display comparirĂ  la scritta ON.
2. Premere [B]. Sul display [F] comparirĂ  la scritta CYC.
3. Premere SET [C] per impostare quali strisce di alimentazione verranno attivate in se-
quenza (da 1 a 4). Ad esempio, selezionando “3”, si attiveranno in sequenza solo le
strisce 1, 2 e 3. La striscia si alimentazione 1 è quella più in basso.
4. Premere SET [C] per impostare la durata dell’alimentazione di ciascuna striscia pre-
mendo [A] per aumentare il minutaggio, [B] per diminuirlo.
5. Premere SET [C] per salvare le impostazioni e ON [D] per attivare la ricarica. Si illu-
mineranno in sequenza i LED corrispondenti alle strisce di alimentazione in tensione
[G] .
6. Portare l’interruttore [E] su ON per avviare la ricarica. Sul display [F] verranno mostrati
i minuti restanti al completamento della sequenza per quella striscia.
Beware: all the following settings should be made in POWER
OFF mode. Turn the [E] switch OFF.
Power on all the power strips at once
1. Press SET [C]. The [F] display will show ON.
2. Press SET [C]. Press [A] to increase, [B] to decrease the minutes of charge. Setting
the timer on “000” the power strips will always be on.
3. Press SET [C] to save the setting and ON [D] to get ready for recharging. All the LEDs
indicating the various power strips [G] will turn on. All the power strips will be on for
the duration set at point 2.
4. Turn the [E] switch ON to start the recharging. On the [F] display will be shown the
minutes left.
Power on a single power strip at a time
1. Press SET [C]. The [F] display will show ON.
2. Press [B]. The [F] display will show CYC.
3. Press SET [C] to set which power strips will be powered in a sequence (from 1 to 4).
Eg. selecting “3” only the power strips from 1 to 3 will be turned on in sequence. The
bottom power strip is the number 1.
4. Press SET [C] to set the charging time for each power strip pressing [A] to increase,
[B] to decrease the minutes of charge.
5. Press SET [C] to save the setting and ON [D] to get ready for recharging. The LEDs
[G] will turn on in sequence showing the power strip currently on.
6. Turn the [E] switch ON to start the recharging. On the [F] display will be shown the
minutes left for each single power strip.
ON
OFF
A B C D
E
F
G

Produktspezifikationen

Marke: HELGI
Kategorie: niet gecategoriseerd
Modell: HLGOMN36BLWH

Brauchst du Hilfe?

Wenn Sie Hilfe mit HELGI HLGOMN36BLWH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd HELGI

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung fĂĽr -Kategorien-