Havis PKG-PSM-120 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Havis PKG-PSM-120 (4 Seiten) in der Kategorie Car Kit. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
A-
GUIDE RING BUSHING REMOVAL
WE STRONGLY RECOMMEND NOT TO REMOVE THE
GUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLE
IS DESIRED - FOLLOW THIS SIMPLE REMOVAL
INSTRUCTION
INSERT MAXIMUM 1" DIAMETER OBJECT WITH
1.
SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.
MAKE SURE NOTHING PREVENTS GUIDE RING
2.
BUSHING FROM BEING EJECTED UNDERNEATH. HIT
WITH A HAMMER TO FORCE THE GUIDE RING
BUSHING OUT.
7/8" - 1"
DIAMETER
OBJECT
SUPPORT ARM
(OPTIONAL)
B -
INSTALL SPIDER COLLAR (OPTIONAL
COMES WITH C-HDM-401 & 403)
IF MOUNTING THE SPIDER COLLAR TO THE INNER
1.
POLE USE CM003406 REDUCING BUSHING. SPREAD
AND SNAP OVER THE INNER POLE.
LOOSELY ATTACH SPIDER COLLAR TO THE OUTER
2.
POLE OR CM003406. DO NOT MOUNT SPIDER
COLLAR ABOVE OUTER POLE HORIZONTAL CUT.
SPIDER MUST BE
BELOW THIS SLOT
ON THE OUTER POLE
C -
INSTALL OPTIONAL C-HDM-416
IF MOUNTING C-HDM-416 TO THE INNER POLE USE
1.
CM003406. SPREAD THE PIECE AND IT SHOULD SNAP
OVER THE INNER POLE.
ATTACH C-PM-101 TO CLAMP ASSEMBLY USING
2.
LONG CARRIAGE BOLTS INSERTED THROUGH THE
PRINTER AND ONE PIECE OF EXTRUSION.
ATTACH POLE CLAMP TO THE OUTER POLE OR
3.
CM003406. AFFIX SECOND PIECE OF EXTRUSION
AROUND POLE AND LOOSELY TIGHTEN THE
HARDWARE. DO NOT MOUNT CLAMP ABOVE
OUTER POLE HORIZONTAL CUT.
CM003406 REDUCING
BUSHING IS NECESSARY
IF MOUNTING TO
THE INNER POLE.
(USE ONLY ON FIXED
HEIGHT POLES)
C-PM-101
SOLD SEPARATELY
D-
INSTALL GAS SHOCK (OPTIONAL)
(SKIP IF GAS SHOCK IS NOT IN USE)
1.
UNSCREW SMALL PLASTIC DISC FROM SHOCK
2.
INSERT GAS SHOCK ASSEMBLY UPWARD FROM
THE BOTTOM OF HDM POLE ASSEMBLY WITH GAS
SHOCK'S ROD FACING DOWNWARD. GAS
SHOCK WILL SANDWICH BETWEEN MOUNTING
BASE C-HDM-100 SERIES (NOT SHOWN) AND
ACTION ADAPTER C-HDM-300 SERIES (NOT
SHOWN).
ONCE GAS SHOCK SITS PROUD OF THE INNER
3.
POLE REATTACH SMALL PLASTIC DISC
GAS SHOCK
(OPTIONAL)
E -
INSTALL C-HDM-409 OPTIONAL
& COLLAR CLAMP ALIGNMENT
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE C-HDM-409.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
F -
INSTALL C-HDM-410-412 OPTIONAL
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE OFFSET.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
45°
MAX.
45°
MAX.
SLOTS IN TUBE
AND CLAMP
ALIGNED
HAMMER
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 12.109
TITLE:
DWG. NO.
C-HDM_INST
REV
A
02/20/13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES
C-HDM-204 SHOWN
STANDARD FLAT SURFACE
MOUNTING
FOR FLAT SURFACE MOUNTING OF C-HDM-
204, 205, 212, 213, 214, 215, 216 AND 217
(INCLUDING HAVIS CONSOLES WHICH DO
NOT HAVE HOLES PRE-DRILLED)
POSITION POLE MOUNT IN DESIRED
1.
LOCATION
MARK AND DRILL 1/4" HOLES INTO THE
2.
MOUNTING SURFACE (SEE NOTES FOR
DRILLING)
THROUGH-BOLT USING 1/4" HARDWARE
3.
PROVIDED WITH THE MOUNT OR
EQUIVALENT HARDWARE IF
NECESSARY.
C-HDM-204 SHOWN
STANDARD CONSOLE SIDE
MOUNTING
FOR CONSOLE SIDE MOUNTING OF C-
HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)
TO ATTACH C-HDM-204, 205, 214, 215
1.
LOOSEN THE RETAINING SET SCREW TO
2.
ALLOW THE NUTS TO BE POSITIONED AS
DESIRED IN THE TRACK.
LINE UP THE MOUNT WITH THE NUTS IN
3.
THE CONSOLE,
ATTACH USING HARDWARE
4.
PROVIDED WITH THE MOUNT, OR
EQUIVALENT 1/4-20 X 1/2" LONG
(MAX.) BOLTS AND FLAT WASHERS.
C-HDM-204 SHOWN
PRE-DRILL;ED CONSOLE SIDE
MOUNTING
FOR CONSOLE SIDE MOUNTING OF C-
HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)
TO ATTACH C-HDM-204, 205, 214, 215
1.
LINE UP THE MOUNT WITH THE
2.
PREDRILLED HOLES IN THE CONSOLE,
ATTACH USING HARDWARE
3.
PROVIDED WITH THE MOUNT, OR
EQUIVALENT 1/4-20 BOLTS.
DEPENDING ON THE DESIRED
4.
POSITION, HOLES MAY NEED TO BE
DRILLED, OR ONE (1) BOLT CAN USE
THE NUT TRACK WITH A 1/4-20 X 1/2"
LONG BOLT.
FOR VEHICLE MOUNTING THAT REQUIRES DRILLING
INSPECT ALL AREAS BEFORE DOING ANY DRILLING
1.
ENSURE NO SERIOUS DAMAGE HAPPENS TO THE
VEHICLE.
SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.
2.
NOTE:
MOST C-VS (VEHICLE SPECIFIC)
SERIES CONSOLES HAVE HOLES FOR
AN HDM-204 OR 214 PRE-DRILLED.
IF ANOTHER LOCATION IS DESIRED,
HOLES MAY NEED TO BE DRILLED
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 2 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 0.00
TITLE:
DWG. NO.
C-HDM_INST
REV
A
02/20/13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES
1/4-20 NYLOCK NUT (2X)
1/4-20 FEMALE HANDLE
C-HDM-301
INCL WITH
C-HDM-302,
303, 304.
GENERAL C-HDM-300's INSTALL INSTRUCTIONS
ALIGN 4 MOUNTING STUDS OF MOUNTING DEVICE C-HDM-
1.
300's INTO THE HDM-200's SERIES MOUNTING SLOTS.
BOLT THE MOUNT TOGETHER USING SPECIFIED AND SUPPLIED
2.
HARDWARE.
TORQUE THE 5/16 HARDWARE TO INDUSTRY STANDARDS .
3.
1/4-20 FEMALE HANDLE CAN BE SUBSTITUTED FOR 1/4-20
4.
NYLOCK NUT.
IF THE C-HDM-300 IS TO BE STATIONARY BOLT DIRECTLY TO
5.
THE POLE USING 5/16-18 HARDWARE.
VISIT US AT www.havis.com TO SEE PICTURES OF
6.
INDIVIDUALLY INSTALLED PRODUCTS.
STEP 3 C-HDM-300's SERIES
INSTALL INTRUCTIONS
1/4-20 THIN
NYLOCK NUT (4X)
SECTION REMOVED FOR CLARITY
C-HDM-402 (OPTIONAL) SAFETY LOCK
WITH C-HDM-305
FOLLOW GENERAL C-HDM-300's INSTALL
1.
INSTRUCTIONS IN "HOW TO ATTACH C-HDM-402
INTO UPPER POLE".
MOUNT C-HDM-305 (SLIDE) TO SAFETY LOCK (C-
2.
HDM-402) USING SHOWN HARDWARE AND
FOLLOWING THE HARDWARE ARRANGEMENT.
THE TOP PLATE CAN BE REMOVED IF NECESSARY
TIGHTEN HARDWARE AND REATTACH TOP PLATE.
3.
C-HDM-402
TOP PLATE
C-HDM-305
1/4-20 X 3/4" HEX HEAD BOLT (4X)
1/4" SPLIT LOCK WASHER, (4X)
1/4" SAE FLAT WASHER, (8X)
C-HDM-301 TO C-MD-200 SERIES
ALIGN 4 MOUNTING STUDS OF MOUNTING DEVICE C-HDM-
1.
300's INTO THE C-HDM-200's SERIES MOUNTING SLOTS.
BOLT THE C-MD-200 TO THE C-HDM-301 PLATE USING THE
2.
SAME HARDWARE CONFIGURATION FOR THE C-HDM-300
SERIES.
TIGHTEN HARDWARE.
3.
C-MKM-100 SERIES TO C-HDM-200
SERIES
NUT AND BOLT TOGETHER USING 5/16-18
1.
HARDWARE CONFIGURATION SHOWN
ABOVE.
C-MD-100 SERIES
PLACE C-MD-100 SERIES MOTION DEVICE ON
1.
TOP OF POLE MOUNTING SURFACE.
LINE UP THE 4 TAPPED HOLES WITH THE UPPER
2.
POLE MOUNTING SLOTS.
ATTACH THE FOUR 1/4-20 HEX BOLTS & LOCK
3.
WASHERS AND FLAT WASHER AS SHOWN
THROUGH THE THREADED HOLES OF THE
MOTION DEVICE.
TIGHTEN HARDWARE.
4.
C-HDM-200's SERIES
(NOT INCLUDED)
5/16-18
HEX NUT(4X)
5/16" SPLIT LOCK
WASHER(4X)
5/16" STEEL
FLAT WASHER (4X)
1/4" PLASTIC
FLAT WASHER (3X)
1/4" STEEL
FLAT WASHER (3X)
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 3 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): N/A
TITLE:
DWG. NO.
C-HDM_INST
REV
A
02/20/13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES
Produktspezifikationen
| Marke: | Havis |
| Kategorie: | Car Kit |
| Modell: | PKG-PSM-120 |
| Produktfarbe: | Schwarz |
| Kompatible Produkte: | 2005-2011 Dodge Dakota |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Havis PKG-PSM-120 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Car Kit Havis
10 März 2024
4 März 2024
24 Januar 2024
21 Januar 2024
13 Januar 2024
3 Januar 2024
27 November 2023
15 November 2023
21 August 2023
Bedienungsanleitung Car Kit
- Car Kit Hama
- Car Kit Manta
- Car Kit SilverCrest
- Car Kit Maginon
- Car Kit Kenwood
- Car Kit Pioneer
- Car Kit Jabra
- Car Kit Motorola
- Car Kit Nokia
- Car Kit Livoo
- Car Kit Plantronics
- Car Kit Scosche
- Car Kit SuperTooth
- Car Kit Parrot
- Car Kit Alpine
- Car Kit AHG
- Car Kit BURY
- Car Kit Mr Handsfree
- Car Kit Boss
- Car Kit Jensen
- Car Kit WAGAN
- Car Kit NAV-TV
- Car Kit Metra
Neueste Bedienungsanleitung für -Kategorien-
4 Juli 2024
1 Juli 2024
29 Juni 2024
29 Juni 2024
14 April 2024
9 April 2024
6 April 2024
2 April 2024
31 März 2024