Gerni 5300 Bedienungsanleitung

Gerni Hochdruckreiniger 5300

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Gerni 5300 (4 Seiten) in der Kategorie Hochdruckreiniger. Dieser Bedienungsanleitung war für 43 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
HIGH PRESSURE WASHER SAFETYGENERAL POWER TOOL SAFETY ELECTRICAL SAFETY
0
I
5300 - 1885PSI
+_
SAFETY
1-23 LETCON DRIVE, BANGHOLME, VICTORIA, AUSTRALIA 3175. 0820
5300
HIGH PRESSURE WASHER
SPECIFICATIONS
VOLTAGE: 230-240V ~50Hz
POWER: 2100W
MAX. PRESSURE: 13 MPa (1885psi)
RATED PRESSURE: 12.5 MPa (1813psi)
MAX. INLET PRESSURE: 1 MPa (145 psi)
RATED FLOW: 7.5L/min
MAX. FLOW RATE: 8.3L/min
HOSE LENGTH: 9m
MAX. WATER INLET TEMP.: 40°C
IP RATING: IPX5
WEIGHT: 18kg
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings
refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool. Power tools are dangerous in the
hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
WARNING! The appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction. Young children should be
supervised to ensure that they do not play with the appliance.
WARNING! High pressure injection injuries are considered to be medical emergencies. In the
event of a high pressure injection injury occurring, seek medical advice immediately.
WARNING! It is prohibited to use Pressure Washers on materials containing asbestos (Cement
sheet roofs, Fences, Walls etc.). Large numbers of asbestos fibres may be released into the air,
posing a serious health hazard. If unsure about the materials you are spraying, it is recommended
that you contact your local council or government authority.
• Before connecting a tool to a power source (mains switch power point receptacle, outlet, etc.) be sure
that the voltage supply is the same as that specified on the nameplate of the tool. A power source
with a voltage greater than that specified for the tool can result in serious injury to the user, as well as
damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
• Unsafe operation of your high pressure cleaner could lead to serious injury or death to you or others.
• The spray gun/wand is a powerful cleaning tool that could look like a toy to a child.
• Improper control of gun/wand can result in injuries to self, others and property damage. Reactive
force from the spray can result in gun/lance movement, potentially causing the operator to slip, fall or
misdirect the spray.
• Become familiar with the operation and controls of the pressure cleaner.
• Keep children away from the pressure cleaner at all times.
• Never modify or remove the safety features of this product.
• Do not operate the machine with missing, broken or unauthorized parts.
• Never leave wand unattended while unit is running.
• Keep work area free of obstacles.
• Stand on stable surface and grip gun/lance firmly. Expect the gun to kick back when engaged
• Do not use to pump flammable or explosive liquids such as gasoline, fuel oil, kerosene,solvents or
thinners. Pump should only be used with liquids compatible with pressure washer component materials.
Failure to follow to this warning can result in serious personal injury, death and/or property damage.
• Only use cleaning agents designed for pressure washers. The use of other cleaning agents or chemicals
may adversely affect the safety and/or operation of the appliance.
• Do not use the appliance within range of persons unless they wear protective clothing.
• High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons,
animals, live electrical equipment or the appliance itself.
• Do not direct the jet against yourself or others in order to clean clothes or foot-wear.
• To ensure appliance safety, use only original spare parts from the manufacturer or approved by the
manufacturer.
• High pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses,
fittings and couplings recommended by the manufacturer.
• Do not use the appliance if a supply cord or important parts of the appliance are damaged, e.g. safety
devices, high pressure hoses, trigger gun.
• Water that has flowed through a back flow preventer is considered to be non-potable.
• Depending on the application, shielded nozzle can be used for high pressure cleaning, which will reduce
the emission of hydrous aerosols dramatically. However, not all applications allow the use of such a
device. If shielded nozzles are not applicable for the protection against aerosols, a respiratory mask of
class FFP 2 or equivalent may be needed, depending on the cleaning environment.
• The electric supply connection shall be made by a qualified electrician and comply with IEC60364-1. It
is recommended that the electric supply to this machine should include either a residual current device
that will interrupt the supply if the leakage current to earth exceeds 30mA for 30ms or a device that will
prove the earth circuit.
• Never touch the mains plug or power outlet with wet hands
• Always disconnect the product from the power outlet when leaving the machine unattended.
• This product must not be connected to the potable water mains without back flow prevention. Check
local and national plumbing regulations before connecting the machine to the potable water mains.
• Do not operate the machine at temperatures below 0 degrees.
• If an extension cord is used, it shall be suitable for outdoor use, and the connection has to be kept dry
and off the ground. It is recommended that this is accomplished by means of a cord reel which keeps
the socket at least 60 mm above the ground.
• It is recommended that a reinforced garden hose (with minimum diameter of 12mm) is used for the inlet
connection.
• During use of high pressure cleaners, aerosols may be formed. Inhalation of aerosols can be hazardous
to health.
WARNING! When using mains-powered tools, basic safety precautions, including the following,
should always be followed to reduce risk of fire, electric shock, personal injury and material
damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electrical motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Gerni tools are interchangeable for Australia and New Zealand.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and
electric shock.
Residual Current Device (RCD)
The pressure washer must be protected by a residual current device (rated at 30mA or less). A residual
current device reduces the chance of electric shock.
WARRANTY
*
WARRANTY
5 Year Standard
+2 Year Online Extension GPW-5300
GERNI Warranty Process
Our goods come with guarantees that cannot be excluded under Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
GERNI – 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175 provides the following warranty in
relation to your Gerni Pressure Washer machine.
DOMESTIC WARRANTY
Definition; A machine purchased for domestic household use.
Gerni warrants that, subject to the exclusions and limitations below, the product will be free from
defects in the materials and workmanship for the duration of the warranty period from the date of
purchase.
2 YEAR STANDARD WARRANTY
Machines & accessories included are as follows: Gerni 3300*, 3600*, 5000*, 9000
*Subject to an additional 3 year extended warranty with online registration at www.gerni.com.au
5 YEAR STANDARD WARRANTY
Machines included are as follows: Gerni 5300*, 7000*, 7300*
*Subject to an additional 2 year extended warranty with online registration at www.gerni.com.au
2 YEAR STANDARD WARRANTY
All Gerni accessories are subject to a 2 year standard warranty, to qualify for an exchange of your
product you must have proof of purchase*.
*Extended warranty is not applicable to Gerni accessories, only pressure washer machines.
GERNI Warranty Claims
Equipment defects covered by the warranty will be repaired or replaced by one of our Authorised
agents within the Gerni organisation. Find your local service agent here: www.gerni.com.au
• If a fault occurs, the user must first take their pressure washer machine to the closest Gerni
Authorised Agent to be diagnosed for fault. It is important that you have the pressure washer
serial number accompanied with your proof of purchase receipt and a copy of your Gerni online-
registration certificate to ensure your pressure washer is covered under warranty.
• If a fault is diagnosed and your machines is inside stated warranty period, then your machine will
be repaired or replaced at no cost. If your machine is diagnosed faulty but your machine has fallen
outside the stated warranty period, the cost of diagnosis or repair will be covered by the user.
Exclusions:
• The product has been modified, repaired, or serviced by someone other than a Gerni authorised
service centre.
• The product has been used other than for the purpose to which it is designed.
• The product has been exposed to user abuse such as knocks, bumps and extreme temperatures
conditions.
1-23 LETCON DRIVE, BANGHOLME, VICTORIA, AUSTRALIA 3175.
+_
0
I
5300 - 1885PSI
1 X HOSE HOOK
ASSEMBLY
GPW-5300
1 MID PATIO CLEANERX
1 X G4 LANCE
GACC-SLG4
1 X G4 SPRAY HANDLE
GACC-SHG4
1 X JET SPRAY
NOZZLE
GACC-JSN
1 X VARIABLE
SPRAY NOZZLE
GACC-VSN
1 X CLEANING
NEEDLE
1 X WATER INLET
COUPLING
0
I
TRANSPORT HANDLE
I
SETUP HIGH PRESSURE HOSE
5300 - 1885PSI
ATTACH INLET COUPLING
a.
b.
a.
b.
ASSEMBLE SPRAY GUN
TRANSPORT HANDLE
CLEANING
NEEDLE SLOT
ACCESSORY SLOT
NOZZLE SLOT
HANDLE LOCK
WHEELS
NOZZLE SLOT
ACCESSORY SLOT
FIT AN ACCESSORY
• For general purpose cleaning.
• Twist to adjust pressure.
• 15° Fan shaped spray.
+_
VARIABLE SPRAY NOZZLE
GACC-VSN
• For removing ingrained dirt.
• High impact rotating jet.
• Covers a larger area.
JET SPRAY NOZZLE
GACC-JSN
COMPONENTS
HIGH PRESSURE
HOSE
LANCE HOLDER
WATER INLET
GUN & LANCE
HOLDER
POWER CORD
HOOK
ON / OFF DIAL
1. Fit
Transport
Handle.
1. Connect
to
Pressure
Outlet.
2. Connect
to Spray
Handle.
1. Align tabs &
insert Lance.
2. Push in & twist
Lance to lock.
3. Press chosen
accessory into Lance.
4. Press button & pull
accessory to detach.
2. Secure with 8mm Screws.
1. Remove cap.
2. Attach
Water
Inlet
Coupling.
1 X TRANSPORT HANDLE
2 X THREADED INSERT1 X 9M HIGH PRESSURE
HOSE
HOSE HOOK
1. Fit Hose
Hook.
1 X FOAM SPRAYER
GACC-FS
• For general purpose
cleaning.
• Allowing for use of
detergent & chemicals.
FOAM SPRAYER
GACC-FS
• For cleaning horizontal surfaces.
• Suitable for brick, cement & wood.
• Variable spray adjustment.
MID PATIO CLEANER
2 X 8MM SCREW
2 X 18MM SCREW
3. Press
& Hold
Lock then
Adjust.
2. Secure with 18mm
Screws.
PRESSURE OUTLET
HIGH PRESSURE
HOSE HOOK
USAGE
GPW-5300
WARNING! High pressure jets can be dangerous if not used properly.
Do not direct the jet at persons, animals, live electrical equipment or
the pressure washer itself.
WARNING! High pressure jets can be dangerous if not used properly.
Do not direct the jet at persons, animals, live electrical equipment or
the pressure washer itself.
WARNING! Perform the procedure below if taking a break for more
than 5 minutes. Failure to do so may damage the pump or cause the
equipment to overheat and malfunction.
CONNECT TO TAP TAKE A BREAK
5300 - 188 5PSI
a.
b.
3
4
1
2
Run water
through hose.
Turn off
tap.
0
I
9
5
6
7
8
Purge pressure.
Release trigger.
Start cleaning.
Switch on ( I ).
Connect water hose.
Unlock Spray Gun.
1
Lock trigger.
0
I
2
Switch off ( 0 ).
b.
a.
3
Switch off & unplug.
4
Turn off
tap.
Power & water.
NOT WORKING?
SYMPTOM POSSIBLE CAUSE RECOMMENDED ACTION
Fluctuating Pressure Pump is drawing in air Check that hoses and connections are airtight
Insufficient water supply Increase water supply at the tap, check for blockages or kinks in the
hose and/or swap to a larger diameter hose
Accessory nozzle dirty or blocked Clean accessory nozzle bore as there may be a blockage from dirt or
debris please use cleaning needle provided
The machine stops
mid-use Incorrect mains voltage Check that the mains voltage corresponds to the specification on the
model tag
Thermal sensor activated Leave pressure washer for 5 minutes to cool down
Nozzle partially blocked Please refer to Care & Cleaning (step 5) section of the user manual
Machine Pulsating/
inconsistent spray Air in the inlet hose/pump Press & hold the spray gun trigger and allow the machine to run until
normal working pressure resumes
Kinked water hose Unwind the water hose fully
Insufficient water supply Increase water supply at the tap, check for blockages or kinks in the
hose and/or swap to a larger diameter hose.
No water emitted Water filter blocked Clean the inlet filter
Blocked nozzle Use cleaning needle to clean outlet
Machine often starts
and stops by itself
Spray gun may be leaking due to
worn/damaged O-ring
Please contact your closest Gerni Authorised Repair Agent
www.gerni.com.au

Produktspezifikationen

Marke: Gerni
Kategorie: Hochdruckreiniger
Modell: 5300

Brauchst du Hilfe?

Wenn Sie Hilfe mit Gerni 5300 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Hochdruckreiniger Gerni

Gerni

Gerni Classic 125.3 Bedienungsanleitung

30 August 2024
Gerni

Gerni 3300 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni Super 145.3 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni Classic 100.5 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni Pro 160.2 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni 3600 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni Super 135.3 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni 7000 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni 5000 Bedienungsanleitung

16 Mai 2023
Gerni

Gerni Super 160.3 Bedienungsanleitung

16 Mai 2023

Bedienungsanleitung Hochdruckreiniger

Neueste Bedienungsanleitung für -Kategorien-

Nilfisk

Nilfisk C 110.3-5 PC X-TRA Bedienungsanleitung

15 Oktober 2024
Meec Tools

Meec Tools 009-875 Bedienungsanleitung

15 Oktober 2024
Sun Joe

Sun Joe SPX3001-RM Bedienungsanleitung

14 Oktober 2024
Worx

Worx WG629.1 Bedienungsanleitung

13 Oktober 2024
Hamron

Hamron 220-118 Bedienungsanleitung

12 Oktober 2024
Eurom

Eurom H195 Bedienungsanleitung

11 Oktober 2024
Kranzle

Kranzle 2175 TST Bedienungsanleitung

10 Oktober 2024
Powerplus

Powerplus POWXG9025 Bedienungsanleitung

10 Oktober 2024
Stiga

Stiga HPS 235 R Bedienungsanleitung

8 Oktober 2024
Hecht

Hecht 323 Bedienungsanleitung

4 Oktober 2024