GE ZIPP360NZ Bedienungsanleitung

GE Kühlschrank ZIPP360NZ

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE ZIPP360NZ (20 Seiten) in der Kategorie Kühlschrank. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/20
Design Guide with
Installation
Instructions
36 Built-In French Door,
Bottom-Freezer Refrigerators
monogram.com
Pub. No. 49-60700
Part No. 224D3560P001
12-13 GE
Safety Information
Skill Level Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the
Owner’s Manual for warranty information.
WARNING:
• These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page 11
for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
AVERTISSEMENT
• Ces réfrigérateurs sont lourds en haut et il faut
les arrimer pour éviter leur basculement. Il faut avoir
un système de protection contre le renversement.
Voir les détails page 11.
• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.
• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.
• Il faut débrancher le réfrigérateur avant le nettoyage
ou toute intervention.
• Les parations doivent être faites par un technicien
qualifié.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.
www. monogram.com
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions
for local inspector’s use. Observe all governing codes
and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions
with your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 9.
AVERTISSEMENT
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à la terre du réfrigérateur », page 9.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product—THREE PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
PRUDENCE
À cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages, IL
FAUT TROIS PERSONNES POUR FAIRE L’INSTALLATION
CORRECTEMENT.
CONTENTS
Planning Guide
The Installation Space ..............................3
Dimensions and Clearances .................3
130° Door Swing .........................................4
90° Door Swing ............................................5
Customization Basics ............................... 6
Panel Dimensions .......................................7
Side Panels ....................................................8
Installation Instructions
Tools, Hardware, Materials ....................9
Grounding the Refrigerator ...................9
Step 1, Remove Packaging ................. 10
Step 2, Install Water Line ..................... 10
Step 2A, RO Water Line ........................ 11
Step 3, Install Side Panels .................... 11
Step 4, Install Anti-Tip Brackets ........ 11
Step 5, Level Refrigerator .................... 12
Step 6, Alternate Anti-Tip Procedure... 12
Step 7, Secure Refrigerator to
Cabinetry ..................................... 12
Step 8, Adjust Door Swing ................... 13
Step 9, Install Grille Panel .................... 13
Step 10, Install Framed Panels ......... 14
Step 10A, Install Overlay Panels ....... 15
Step 11, Connect Water Supply ....... 16
Step 12, Connect Power ....................... 16
Step 13, Start Icemaker ........................ 16
Step 14, Install Toekick ......................... 17
36" Frame to
Frame Width
*84" From
Floor to
Top Frame
35"
Case Width
*83 1/2"
at
Rear
25-3/8" Framed Models
25-3/4" Stainless Steel Models
Case Depth
Depth Including Handles:
27" Framed Models
27-13/16" Stainless Steel Models
28-5/8" Pr sofessional Style Model
THE INSTALLATION SPACE
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24
The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Allow minimum 1/8” air gap between case back & wall.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed
the 24 installation depth shown. The top case trim
overlaps the bottom of the soffit.
Additional Specifications
A 115 volt 60Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be located
on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water line can enter the opening through the floor
or back wall. Route GE SmartConnect kit or 1/4 O.D.
copper tubing between the cold water line and the
water connection location. The tubing should be
long enough to extend to the front of the refrigerator.
Installation of an easily accessible shut-off valve in the
water line is required.
DIMENSIONS AND CLEARANCES
* Shipping height. The
refrigerator can be
adjusted to fit into a
cutout that is 83-1/2
min. to 84-1/2 max.
height. Note that the top
case trim at the front is
1/2 higher and will
overlap upper cabinetry
or soffit. Use leveling
legs and wheels for a
maximum 1 height
adjustment.
Product Clearances
These refrigerators are equipped with a 2-position door
stop. The factory set 130° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
3
23-7/8"
Behind
Frame
90°90° 18-1/8"
18-3/16”
*4” Stainless and
Framed Models.
5” Pro Series *Min. Distance
to Wall
(Stainless
&
Pro Models)
(Framed
Models)
6"
Wall View
Electrical
Area
85"
Finished
Opening
75" From
Floor to
Bottom
of Electrical Ar
ea
10"
24" Cutout Depth
35-1/2"
Finished Width
2-5/16"
5"
10"
10"
5"
3-1/2"
W yater Suppl
12-1/8"
Min. to
Wall
12-1/8"
Min. to
Wall
130°
130°
The finished
cutout width
must be
35-1/2 .
Allow 12-1/8 minimum clearance for a full 130° door
swing.
For a 90° door swing, allow 4 min. clearance to a wall,
for framed and stainless steel models. Allow 5 min.
clearance for professional style models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.
Design Guide


Produktspezifikationen

Marke: GE
Kategorie: Kühlschrank
Modell: ZIPP360NZ

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE ZIPP360NZ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Kühlschrank GE

Bedienungsanleitung Kühlschrank

Neueste Bedienungsanleitung für -Kategorien-