GE UPK4 Bedienungsanleitung

GE Kühlschrank UPK4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE UPK4 (12 Seiten) in der Kategorie Kühlschrank. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/12
Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
Installation Drain Pump
Instructions Kit UPK4
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT – Save these
instructions for local inspector’s use.
• IMPORTANT – Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Proper installation is the responsibility of installer.
• Product failure due to improper installation is not
covered under the Warranty.
WHAT YOU WILL NEED:
3/8” open/box wrench or adjustable wrench
Drill with phillips head bit or #2 Phillips screwdriver
Slip joint pliers
Side cutting pliers
31-1000617 Rev. 2 09-22 GEA
1
3
2
4
5
7
8
9
6
KIT CONTENTS:
1 - Drain Pump & Check Valve Assembly (1)
2 - PVC Drain Pipe & Pressure Sensor
Assembly (1)
3 - Rubber Pad (For Pump Mounting) (1)
4 - Discharge Tubing - Clear (1)
5 - Metal Clamp (For Discharge Tubing) (1)
6 - Plastic Snap Ring (1)
7 - Pump Fixing Bolts (2); Spring Washer (2);
Flat Washer (2)
8 - Pressure Sensor Case Screw (ST/4*12) (1)
9 - Ground Screw With Washer (M/4*8) (1);
Lock Washer(1)
NOTE: This pump can be installed in a cube ice machine or
a nugget ice machine.
231-1000617 Rev. 2
Installation Instructions
INSTALLING PUMP KIT (Cont.)
DISCONNECT ELECTRICAL POWER
1 REMOVE ACCESS COVER
Ŷ Use a drill or a Phillips screwdriver to remove the
2 screws from the access panel as shown in figure
below. Slide the panel in the direction shown to
remove.
2 REMOVE DRAIN TUBING
Ŷ Remove the plastic snap ring from the main drain
tube and release the small metal clamp on the
short drain tube which connected outlet valve. Pull
both tube down. Remove the small metal clamp
from the tube. Keep both snap ring and clamp for
pump kit installation
Ŷ Remove the white drain pipe by pulling it down
from the 2 locations shown.
3 INSTALL RUBBER PAD TO NEW
PUMP
Ŷ Remove the rectangular rubber pad from pump
kit and peel off the white sticker. Attach the sticky
side to the drain pump base.
WARNING Electrical Shock Hazard
Death or serious injury can result from failure to
follow these instructions.
• Service by a qualified service technician only.
• Disconnect power before servicing this product.
• Reconnect all grounding devices after service.
• Replace all parts and panels before operating.
Screws
Access
Panel
Slide panel in
this direction
White Sticker
Rubber Pad -
Sticky side up
Snap
Ring
Short
Drain
Tube
Main
Drain
Tube
Outlet
Valve
Small
Metal
Clamp
31-1000617 Rev. 2 3
4 INSTALL NEW DRAIN TUBING
Ŷ Install the new white drain tubing in the
accessories to the drain pump and clamp with the
snap ring included in the kit.
5 INSTALL THE DRAIN PUMP
Ŷ Insert the red connector of the drain pump into the
red connector you will see on a wire inside of the
ice machine.
Ŷ Slide the drain pump into the ice machine so the
base slides under the tab on the base of the ice
machine floor. The front of the pump with the hose
attached will face the front of the ice machine.
5 INSTALL THE DRAIN PUMP
(Cont.)
Ŷ Using the hardware from the kit, attach the pump
to the ice maker floor using a wrench.
6 CONNECT DRAIN PUMP TO ICE
MACHINE
Ŷ Slide the small metal clamp, which you saved
from original tube assembly, on the short drain
tube of the PVC drain pipe as shown in the picture
below. Push the pipe up to connect both tubes
to the fittings from the ice machine which you
disconnected earlier. Snap and secure the snap
ring back on the connection of the main drain tube.
Slide up and secure the small metal clamp up and
tighten at the connection.
Installation Instructions
INSTALLING PUMP KIT (Cont.)
White Drain
Tubing
Snap Ring
Red Connectors
Tab

Produktspezifikationen

Marke: GE
Kategorie: Kühlschrank
Modell: UPK4

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE UPK4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kühlschrank GE

GE

GE GTS18TBSWW Bedienungsanleitung

13 Oktober 2024
GE

GE DSS25KGRWW Bedienungsanleitung

13 Oktober 2024
GE

GE Profile PFSF5NFXWW Bedienungsanleitung

10 Oktober 2024
GE

GE GTS22WCMCC Bedienungsanleitung

8 Oktober 2024
GE

GE Profile PTS22LCPCC Bedienungsanleitung

7 Oktober 2024
GE

GE ZIDI240WII Bedienungsanleitung

4 Oktober 2024
GE

GE ESS25LGPWW Bedienungsanleitung

3 Oktober 2024
GE

GE GFE26GGKWW Bedienungsanleitung

2 Oktober 2024
GE

GE TBX14SYBLWW Bedienungsanleitung

2 Oktober 2024
GE

GE Profile TFG28PFDBS Bedienungsanleitung

2 Oktober 2024

Bedienungsanleitung Kühlschrank

Neueste Bedienungsanleitung für -Kategorien-

Samsung

Samsung RT32K5030EF Bedienungsanleitung

16 Oktober 2024
Liebherr

Liebherr CBNes 4875 Bedienungsanleitung

16 Oktober 2024
AEG

AEG Santo 70318 KG1 Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBF25285X Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBF28597X Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBRF21785CH Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBRF21785R Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBF21785C Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBF25285C Bedienungsanleitung

16 Oktober 2024
Freggia

Freggia LBF28597C Bedienungsanleitung

16 Oktober 2024