GE SBSD137HGG Bedienungsanleitung

GE Trockner SBSD137HGG

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE SBSD137HGG (12 Seiten) in der Kategorie Trockner. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
Installation
Instructions
KIT CONTENTS
4 Support Pads
4 Mounting Screws
Drawer Divider
1
SBSD137, SBSD227
TOOLS YOU WILL NEED
Phillips Head
Screwdriver
9/16″Open End Wrench
or Adjustable Wrench
8 mm Socket Wrench
REMOVE THE LEVELING LEGS
Carefully lay the washer or dryer on its
side to access the leveling legs on the
bottom of the appliance.
IMPORTANT: Do not lay the washer or dryer
on its back! Do not remove the shipping
bolts on the back side of the washer. The
bolts must remain in place until the washer
is returned to an upright position.
Use an open-end wrench to remove the
washer or dryer leveling legs.
B
A
1
INSTALLATION PREPARATION
Remove the packaging.
The Drawer divider is taped at the top of the
shipping carton. Remove the divider and set
aside for final installation.
Flatten the product carton to use as a pad
to lay the washer or dryer down on its side.
Continue using the carton to protect the finished
floor in front of the installation location.
Back out and remove
all 4 leveling legs
Instructions en français : . . . . . . . . . . . .4
Instrucciones en español: . . . . . . . . . . .8
For Washer Models: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626,
GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626
and WHDVH660
For Dryer Models: DBVH510, DBVH512, DCVH515, DCVH660, DHDVH52,
DHDVH66, PBVH415, PCVH565, PDVH515, PHDVH52 and PHDVH57
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•IMPORTANT —Save these
instructions for local inspector’s use.
•IMPORTANT —Observe all
governing codes and ordinances.
•Note to Consumer – Keep these
instructions with your Owner’s Manual
for future reference.
•Completion time – 1 to 2 hours
•Proper installation is the responsibility
of the installer.
•Product failure due to improper installation
is not covered under the Warranty.
CAUTION — Due to the size and
weight of these products, and to reduce the
risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
•See washer and dryer installation
instructions for additional installation
requirements and guidelines.
2
Installation Instructions
INSTALL THE PEDESTAL
TO THE WASHER OR DRYER
Place the pedestal against the bottom
of the unit. Check to be sure the drawer
front is at the front of the unit.
Align the holes in the pedestal with
the holes in the bottom of the unit.
Use a Phillips screwdriver to install
the 4 screws through the pedestal
and into the unit—do not tighten.
Slide the pedestal toward the unit,
until it is aligned front to back. Use an
8 mm socket wrench to securely tighten
the screws.
C
B
A
3
PREPARE THE PEDESTAL
Pull the
drawer out
as far as it
will go.
Remove
screws from
drawer slides.
Slide drawer
out of the base
and set aside.
FOR DRYERS ONLY:
Locate the 4 support pads from the parts
package. Each pad has 2 protrusions that
fit into the holes on top of the pedestal.
Press the rubber pads into each set of
corner holes on the top of the pedestal
as shown.
NOTE: The support pads should be installed
on the dryer only. DO NOT INSTALL THESE
PADS ON THE WASHER PEDESTAL.
C
B
A
2
3
Installation Instructions
LEVEL THE WASHER OR DRYER
Locate the 4 legs from the parts package
and install.
Stand the washer or dryer upright. Move
it close to its final location.
Make sure that the washer or dryer
is level by placing a spirit level on top.
Check side to side and front to back.
Use an open
ended wrench
to adjust the
legs in and
out. Tighten
the lock nut
against the
bottom of
the pedestal.
NOTE: To minimize vibration, the locking
nuts must be tight.
D
C
B
A
4
REMOVE SHIPPING SCREWS
Remove the 4 shipping screws on the back side
of the unit.
6
REINSTALL THE DRAWER
Check to
be sure the
slides are
closed.
Slide the
drawer
into the
opening.
Align the
drawer
supports to
the slides on
each side.
Reinstall the original screws into each
drawer slide. Tighten both screws.
Open the drawer fully. Slide drawer
divider into slots in the center of the
drawer. The drawer should slide
smoothly when you push it closed.
D
C
B
A
5
FINALIZE THE INSTALLATION
Refer to the washer or dryer Installation
Instructions to complete the installation.
7
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Drawer
divider


Produktspezifikationen

Marke: GE
Kategorie: Trockner
Modell: SBSD137HGG

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE SBSD137HGG benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Trockner GE

Bedienungsanleitung Trockner

Neueste Bedienungsanleitung für -Kategorien-