GE Profile JS966CDCC Bedienungsanleitung

GE Herde Profile JS966CDCC

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr GE Profile JS966CDCC (12 Seiten) in der Kategorie Herde. Dieser Bedienungsanleitung war fĂĽr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/12
Skill Level: Average High Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
CAUTION: Before you begin
Read these instructions carefully and
completely.
• IMPORTANT- Save these instructions for
local inspector’s use.
• IMPORTANT- Observe all governing codes
and ordinances.
Self Cleaning Radiant
Electric Slide-In Range
Installation
Instructions JSP46, JSP56, JS966
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded. See “Electrical
Requirements” page 2.
Parts Included
Tools You Will Need
Pub. No. 31-10426
229C4053P412 1
“If you have questions, Call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
1/4”Nut
driver
Wrench or Pliers
(for 1 7/16” nut)
Pencil
Hand or
Saber Saw
Straight Edge
or Square
Materials Needed
Lag Bolts Anchor
Sleeves 4- Wire Cord
4’long
3 -Wire Cord
4’long
(For Concrete Floors
Only)
( UL Approved 50 AMP)
OR
1
2
3
4
Drill with
1/8” Bit
Anti-Tip Bracket
Screws
Safety
Glasses
Tape Measure Pliers
Level
Rear Filler
2 Screws
All rough-in and spacing dimensions must be met
for safe use of your range. Electricity to the range
can be disconnected at the outlet without moving
the range if the outlet is in the preferred location
(remove lower drawer).
To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet
storage space is to be provided above the
cooktop, the risk can be reduced by installing a
range hood that sticks out at least 5” beyond the
front of the cabinets. Cabinets installed above a
cooktop must be no deeper than 13”.
Be sure your appliance is properly installed and
grounded by a qualified technician.
WARNING: For personal safety
remove house fuse or open circuit
breaker before beginning
installation. Failure to do so could result in
serious injury or even death.
For Your Safety
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of
tipping, the appliance must be
secured by properly installing the
anti-tip bracket packed with the appliance.
If you pull the range out and away from the wall
for any reason, make sure the Anti-Tip bracket
is engaged when the range is pushed back
against the wall.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as specified on the rating plate. The
rating plate is located above the storage drawer
on the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
oven according to governing codes could result in
a hazardous condition. If there are no local
codes, your range must be wired and fused to
meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to
an electric range. When installing an electric
range in new construction, follow the instructions
in the section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for use
with aluminum wiring must be used.
Electrical Requirements
WARNING
• All ranges can tip
• Injury to persons could result
• Install anti-tip bracket
packed with range
• See Installation Instructions
3
Installation Instructions
Pre- Installation Checklist
Inspect Installation Location
Refer to alternate construction section for
the following non standard installations.
a. Counter opening extends to the wall:
Maintop Filler (supplied with the range.)
(See Page 12 section AA for Installation
Instructions) or
Backguard (Kit JXS36XX or JXS39SS).
See page 12.
b. Counter height greater than 36 3/4”:
Lower Trim Slide-In (Kit JXS56XX).
c. One side is not enclosed by a cabinet:
Bodyside (Kit JXS76XX).
d. Island Installation:
To provide an optimum installation, the
top surface of the counter top must be
level and flat (lie on the same plane)
around the 3 sides that are adjacent to
range cooktop. Proper adjustments to
make the top flat should be made or
gaps between the countertop and range
cook top may occur. Forcing the cook
top to fit may cause excessive gaps and
could break glass and void warranty.
Inspect cutout dimensions and location
of receptacle to be sure it fits within
layout location.(See page 5.)
Do not remove the protective channel
from the sides of the glass cooktop, if
applicable, until later in installation.
Move Range Indoors In front
of Cabinet Opening
(Do not use hand trucks when moving the
unpackaged range.)
Protect the kitchen floor! Flatten and
place a piece of the shipping carton in front
of the installation location to protect the
flooring.
Carefully, tilt the range to access the range
leveling legs. Use an adjustable wrench to
screw leveling legs out so that glass
support flanges clear top of counter top.
To Procure Kits:
a. Visit GE Web Site, see page 1.
b. Call GE Answer Center, see page 1.
c. Contact Dealer
Protective Channel
Adjust

Produktspezifikationen

Marke: GE
Kategorie: Herde
Modell: Profile JS966CDCC

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE Profile JS966CDCC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Herde GE

GE

GE Profile PLD621DWBB Bedienungsanleitung

27 Juni 2024
GE

GE Profile PLD621EWSB Bedienungsanleitung

27 Juni 2024
GE

GE GRF400SVWW Bedienungsanleitung

27 Juni 2024
GE

GE GGS500PVSS Bedienungsanleitung

27 Juni 2024
GE

GE Profile PLD621RWSS Bedienungsanleitung

27 Juni 2024
GE

GE GRF500PVES Bedienungsanleitung

27 Juni 2024
GE

GE GGF600AVSS Bedienungsanleitung

27 Juni 2024
GE

GE GRF500PVWW Bedienungsanleitung

27 Juni 2024
GE

GE GGS600AVES Bedienungsanleitung

27 Juni 2024
GE

GE GGF600AVES Bedienungsanleitung

27 Juni 2024

Bedienungsanleitung Herde

Neueste Bedienungsanleitung fĂĽr -Kategorien-

Nemco

Nemco 9130A Bedienungsanleitung

18 August 2024
Meireles

Meireles MI 1600 Bedienungsanleitung

12 August 2024
BEKO

BEKO HIGG 64123 SB Bedienungsanleitung

5 August 2024
NABO

NABO KFC 6060 Bedienungsanleitung

28 Juni 2024
NABO

NABO KFI 6010 Bedienungsanleitung

28 Juni 2024
NABO

NABO KFC 3000 Bedienungsanleitung

28 Juni 2024
NABO

NABO HS 4062 Bedienungsanleitung

28 Juni 2024
AEG

AEG TI64IB10IZ Bedienungsanleitung

27 Juni 2024
BORA

BORA M Pure Bedienungsanleitung

27 Juni 2024
BORA

BORA Basic Bedienungsanleitung

27 Juni 2024