GE JX827CD Bedienungsanleitung

GE magnetron JX827CD

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE JX827CD (4 Seiten) in der Kategorie magnetron. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
Installation instructions
for your new
Parts List
1. Base Pan
2. Rear Duct
3. Side Covers (2)
4. Top Trim
5. Bottom Trim
6. Side Trims
7. Rear Holddown Brackets
Screws A (9 required 1 extra)
B (4 required 1 extra)
C (10 required 2 extra)
D (4 required 1 extra)
E (4 required 1 extra)
Note: This kit has extra screws to prevent technician from spending extra time locating a replacement in case
they lose one during installation.
Cabinet Cutout Dimensions and Specifications
Allow 1-1⁄4" for overlap of the Microwave Oven Kit
Trim over all the edges of the cutout for the
Microwave Oven Kit.
WIDTH HEIGHT
24-7⁄8"±1⁄16" 15"±1⁄16"
DEPTH
16" Min. receptacle outside cutout
18" Min. receptacle inside cutout
120 volt—60 Hertz grounded power receptacle.
For Installation Above a Built-In Oven
Microwave oven should be installed on a
3⁄8" plywood base and supported by 2x4 or
1x2 equivalent runners on all sides. Base
must be capable of supporting a minimum
of 100 lbs.
Screw EScrew D
1
Parts Inventory
B
2
4
5
6
C
A
E
D
7
33
Screw C
Screw A Screw B
CAUTION:
• Before you begin—Read these instructions, Owner’s Manual and Important Safety Instructions
completely and carefully.
• This Kit is for use on models: JEM21K/L, JEM23K/L, JEM25L/GN/GV/GY/WN/WV/WY/BF/WF, JES833WY,
JEM825K, JEM27KWH/LWH, JEM31L/M/GN/GV/GY/WV/WY/GA/WA/CA/BF/CF/WF/SF, JEM33L/M, JEM34M
and ZEM200WN/WV/WY/GV/GY/SY/GW/WA/SA/GA/SF/BF/WF.
• This kit can be installed alone or over any General Electric/Hotpoint/RCA single electric wall oven.
• Do not alter or modify any part of this kit or the oven.
• Observe all governing codes and ordinances.
• Oven must be plugged into a properly grounded 3-hole, 120 volt receptacle as required by the
National Electrical Code.
• Unplug the microwave oven before attempting installation of this kit.
• Save these instructions (for Local Inspectors and Future Reference).
18" Min.
receptacle
in cabinet
16" Min.
receptacle
outside
cabinet
24-7⁄±⁄8" 1 16"
15" 1±⁄16"
TRIM
STRIPS
16-1/4"
26-1/8"
Microwave Oven
Built-In Trim Kit
JX827BN, JX827WN,
JX827SS, JX827CD
Tools Needed
2 Phillips head screwdrivers (#1 & #2)
Drill and 3/32" drill bit
Centerpunch or nail
Pencil and ruler
Knife
Installation Procedure
Step 2
Installation of Base Pan
Disconnect microwave oven from recep-
tacle. Remove everything out of the
microwave oven (packing, glass shelf,
temperature probe, Use & Care books).
Remove the four top plug buttons from
the top of the Microwave Oven cabinet.
Use knife to pry up plug buttons using
care not to scratch the microwave oven.
A clear protective film has been applied to
some microwave oven cabinets. If applied,
remove the film. Place the microwave
oven on the base pan
(1) centered left to right.
V Notch
Remove 4 Plug Buttons
120V/60 Hertz
Grounded Power
Outlet
V Notch
Screw C
Drive two Screws
(C) into the Base
Pan front flange to
hold in place
temporarily.
using the two holes in the Base Pan front flange as your guide
(center the drill in the base holes keeping the front flange
centered and tight against the cabinet front wall).
Slide the two Rear Holddown Brackets (7) from the rear into
the slots in the Base Pan. The tongues of the Rear Holddown
Brackets should be sticking into the base, be centered in the slot,
and be into the slot as far as it will go. Mark and drill four 3/32"
diameter holes. Mount the Rear Holddown Brackets using four
Screws (B). Both Rear Holddown Bracket tongues should now be
centered in the slotted holes in the base and be into the base as
far as they can go.
Remove the two screws in the Base Pan front flange and slide the
Base Pan straight out.
Screw B
Step 1
Locating and Installing Rear
Holddown Supports
Set Base Pan (1) into the front cabinet
microwave oven cutout and center it right
and left. Push back until front flange is
against cabinet front wall. Use the V-notch
in the Base Pan front flange to center the
Base Pan. Bore two 3/32" diameter holes
into the wooden cabinet base front edge
Screw E
Screw A
Step 3
Installation of Side Cover
Install Side Covers by inserting the Side
Cover (3) bottom between the oven and
the side of the Base Pan. Drive two Screws
(A) through the Base Pan into the Side
Cover bottom. Drive two Screws (E)
through the Side Cover into the micro-
wave oven holes where the microwave
plug buttons were removed. Be sure the
side covers are tight against the sides of
the microwave oven (the trim frame
screws will not align unless the side covers
are tight against the microwave oven).
Complete side covers installation by
installing both side covers. Remove the
screw located on the top left back of the
microwave oven cabinet. Save and replace
it when installing the rear duct.
Step 4
Installation of Rear Duct
Install Rear Duct by inserting the Rear
Duct (2) bottom flange between the oven
and the back of the Base Pan. The Rear
Duct should be as far to the left as
possible. The Rear Duct back must go
between the Base Pan back flange and the
partition on the right side. Drive one
screw (A) through the rear duct into the
partition in the Base Pan. Drive one screw
(A) into the rear duct side flange near the
lamp cover. Drive three screws through
the Base Pan into the rear duct bottom.
Replace the screw removed from the top
left to complete the rear duct installation.
The Base Pan should be completely sealed
to the microwave oven in the back and all
screws installed in Steps 3 & 4 tightened.
Screw A
Screws A
Screws E
REMOVE &
SAVE SCREW
CAUTION: Start all screws in Steps 3 & 4
before tightening any one screw.
Step 5
Installation of the Microwave Oven
Plug the power cord into the wall recep-
tacle. Slide the microwave oven assembly
gently into the cabinet using care not to
pinch the power cord, and to keep it
centered as it slides back to where the
holddown bracket’s tongue goes through
the rear slots. The unit should now be
centered right to left in the opening and
the Base Pan front flange tight against the
cabinet. Drive two screws (C) through the
Base Pan front flange into the holes
initially drilled.
Screw C
C
L
Screw CV Notch
Screws A
Replace screw,
removed in Step 3
Screws A
Rear Duct
Base Pan
Partition
in Base Pan

Produktspezifikationen

Marke: GE
Kategorie: magnetron
Modell: JX827CD

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE JX827CD benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung magnetron GE

GE

GE Profile JVM1661WB Bedienungsanleitung

11 Oktober 2024
GE

GE Profile JVM1661CB Bedienungsanleitung

2 Oktober 2024
GE

GE HVM1540LPCS Bedienungsanleitung

22 September 2024
GE

GE JXA019K Bedienungsanleitung

18 September 2024
GE

GE GCST09N1 Bedienungsanleitung

6 September 2024
GE

GE GCST11N1 Bedienungsanleitung

6 September 2024
GE

GE GCST20S1 Bedienungsanleitung

5 September 2024
GE

GE GCST10A1 Bedienungsanleitung

5 September 2024
GE

GE Profile PWL1126SWSS Bedienungsanleitung

5 September 2024
GE

GE JVM1730DMWW Bedienungsanleitung

3 September 2024

Bedienungsanleitung magnetron

Neueste Bedienungsanleitung fĂźr -Kategorien-

Samsung

Samsung CP360W Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung MG32DG4524AGGY Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung MG1040WC-5 Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung ME1040WE Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung MS123HCE Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung ME1040WC5B Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung M1974N Bedienungsanleitung

16 Oktober 2024
Samsung

Samsung PG3210 Bedienungsanleitung

16 Oktober 2024
Hamilton Beach

Hamilton Beach P100N30AP-S3B Bedienungsanleitung

15 Oktober 2024
Whirlpool

Whirlpool WMCS7022RS Bedienungsanleitung

15 Oktober 2024