GE JVM1350SY Bedienungsanleitung

GE Mikrowelle JVM1350SY

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für GE JVM1350SY (12 Seiten) in der Kategorie Mikrowelle. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/12
Installation Instructions
Microwave Oven
Read carefully.
Keep these Instructions.
2
INSTALLATION INSTRUCTIONS
Mounting Space
This section describes the space you need to install
your microwave oven.
Your Over-the-Range microwave oven requires
mounting space on a wall as shown.
1. A minimum of 30 between the cabinets is″
required for installation. If the space between
the cabinets is greater than 30 , a Filler Panel ″
Kit may be used to fill in the gap between the
microwave oven and the cabinets. Your Use
and Care Guide contains the kit number for
your model.
2. Make sure the bottom edge of the cabinet that
will be above the microwave oven is at least 66″
from the floor and 30 from the cooking surface.″
3. For easier access to change the hood and range
lamps, the bottom of the microwave oven should
be at least 2 above the range backsplash.″
4. If you are going to vent your microwave oven
to the outside, see Section 5 for exhaust duct
preparation.
5. When installing the microwave oven beneath
smooth, flat cabinets, be careful to follow
the instructions on the top cabinet template
for power cord clearance.
REQUIREMENTS FOR INSTALLATION
Important Safety Instructions
This product requires a three-prong grounded
outlet. The installer must perform a ground
continuity check on the power outlet box before
beginning the installation to insure that the outlet
box is properly grounded. If not properly grounded,
or if the outlet box does not meet electrical
requirements noted (under ELECTRICAL
REQUIREMENTS), a qualified electrician should
be employed to correct any deficiencies.
CAUTION: For personal safety, remove house
fuse or open circuit breaker before beginning
installation to avoid severe or fatal shock
injury.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this 65 pound product, plus additional oven
loads of up to 50 pounds or a total weight of
115 pounds.
CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements
such as an island or a peninsula. It must be
mounted to both a top cabinet and a wall.
1
Electrical Requirements
Product rating is 120 volts AC, 60 Hertz, 14.3 amps,
and 1.46 kilowatts. This product must be connected
to a supply circuit of the proper voltage and
frequency. Wire size must conform to the
requirements of the National Electric Code or the
prevailing local code for this kilowatt rating. The
power supply cord and plug should be brought to
a separate 15 to 20 ampere branch circuit single
grounded outlet. The outlet box should be located
in the cabinet above the microwave oven. The outlet
box and supply circuit should be installed by a
qualified electrician and conform to the National
Electric Code or the prevailing local code.
NOTE: For easier installation and personal safety,
it is recommended that two people install this
product.
Bottom Edge
of Cabinet
Needs to be
30 or More″
From the
Cooking
Surface Backsplash
66 or More″
From the
Floor to the
Top of the
Microwave
30″
You should have the wall
receptacle and circuit
checked by a qualified
electrician to make sure
the receptacle is
properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is very important to have it
replaced with a properly grounded three-prong
wall receptacle, installed by a qualified
electrician.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT, DEFORM, OR REMOVE ANY OF THE
PRONGS FROM THE POWER CORD. DO
NOT USE WITH AN EXTENSION CORD.
IMPORTANT—PLEASE READ CAREFULLY.
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED TO
AVOID SEVERE OR FATAL SHOCK.
The power cord of this appliance is equipped
with a three-prong (grounding) plug which
mates with a standard three-prong (grounding)
wall receptacle (Fig. 1) to minimize the
possibility of electric shock hazard from
this appliance.
2″
30″
16-1/2″
Insure proper ground exists
before use
Fig. 1
PARTS INCLUDED
You will find the installation hardware contained
in a packet with the unit. Check to make sure
you have all these parts. The installation
hardware (1–6) should include the following:
Hardware List Quantity
(some extra parts are included)
1. Wood Screws (1/4 x 2 1″ ″)
2. Toggle Bolts (and wing nuts) 2
3/16 x 3″ ″
3. Machine Screws (1/4 x 2″3
/4″) 4
4. Washers 4
5. Nylon Grommet (for metal cabinets) 2
6. 28 Piece of Foam Tape 2″
In addition you will need:
Top Cabinet Template 1
Installation Instructions 1
Separately Packed Grease Filters 2
2
OVERVIEW OF INSTALLATION PROCEDURE
This section gives a brief overview of what you
need to do to install this microwave. Read these
entire instructions before you begin installation.
Before you install this microwave, remove the
adhesive tape, if there is any, on the exhaust
adaptor, grease filters and power supply cord.
1. Install an outlet and make sure you meet the
electrical requirements for this installation.
2. Open the installation hardware packet.
Compare it to the hardware list to make sure
you have all the parts.
3. Remove the mounting plate.
4. Check the microwave exhaust duct and
change it if required.
5. Attach the mounting plate to the wall.
6. Slide the microwave onto the mounting plate.
7. Attach the microwave oven to the top cabinet.
TOOLS YOU WILL NEED
• Phillips screwdriver
• Pencil
• Ruler or tape measure and straight edge
• Carpenter square (optional)
• Tin snips (in some applications)
• Electric drill with 3/16 , 1/2 and 5/8 drill bits″ ″ ″
• Hammer
• Stud finder (optional)
• Filler blocks, if needed for top cabinet spacing
• Gloves
• Saw (jig or keyhole)
Your cabinets may have trim that interferes
with the microwave installation. You may
need to remove the trim in order to fit the
microwave in and to make it level.
The space must be 30 wide. Remove any″
cabinet side trim that interferes with the 30″
space, front or back.
THE MICROWAVE MUST BE LEVEL.
If the cabinets have top trim (front, back or
both), this can be left in place if there is still
enough clearance for proper installation.
If you leave the top front trim on, and there is
no back trim, make sure the mounting plate
is positioned down far enough to keep the
microwave level. Keep the space between the
bottom of the cabinet and the mounting plate
equal to the height of the top front trim. This
will insure level installation of the microwave.
30″
Back
Wall
Mounting
Plate Must
be Installed
So That the
Microwave
is Level
Height of the
Top Front Trim
3
1
2
4
5
6
3

Produktspezifikationen

Marke: GE
Kategorie: Mikrowelle
Modell: JVM1350SY

Brauchst du Hilfe?

Wenn Sie Hilfe mit GE JVM1350SY benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Mikrowelle GE

GE

GE JX52BL Bedienungsanleitung

6 August 2024
GE

GE JEB1095DVBB Bedienungsanleitung

26 Juni 2024
GE

GE JNM3184DPBB Bedienungsanleitung

26 Mai 2024
GE

GE Profile JVM1661SB Bedienungsanleitung

25 Mai 2024
GE

GE JVM1440LK Bedienungsanleitung

5 Mai 2024
GE

GE Profile JX1530CBH Bedienungsanleitung

3 Mai 2024
GE

GE JX2130SH Bedienungsanleitung

30 April 2024
GE

GE JVM1440BA Bedienungsanleitung

15 April 2024
GE

GE LVM1750DMWW Bedienungsanleitung

14 April 2024
GE

GE JX36DES Bedienungsanleitung

30 März 2024

Bedienungsanleitung Mikrowelle

Neueste Bedienungsanleitung für -Kategorien-

LG

LG MB-359MB Bedienungsanleitung

20 August 2024
LG

LG MS-2012G Bedienungsanleitung

19 August 2024
Becken

Becken Easy Cook Max 2 Bedienungsanleitung

15 August 2024
Saturn

Saturn STMW8153 Bedienungsanleitung

9 August 2024
Rosières

Rosières RMG350EIN Bedienungsanleitung

8 August 2024
ICES

ICES IMO-25L63 Bedienungsanleitung

5 August 2024
NABO

NABO MWO 2002 Bedienungsanleitung

28 Juni 2024
NABO

NABO MWO 2900 Bedienungsanleitung

28 Juni 2024
NABO

NABO MWU 2015 Bedienungsanleitung

28 Juni 2024
NABO

NABO MWE 2050 Bedienungsanleitung

28 Juni 2024