Garmin Fishfinder 80 Bedienungsanleitung
Garmin
Fischfinder
Fishfinder 80
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Garmin Fishfinder 80 (3 Seiten) in der Kategorie Fischfinder. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
Flush Mount Installation Instructions
Contents:
Mounting Hardware:
A - Foam Rubber Pads (2)
B - M4x40mm Hew Head Screws (4)
C - M4 Hex Nuts (4)
D - Reusable Cable Tie (1)
E - Metal Retaining Brackets (2)
Please read through these instructions thoroughly before attempting installation. Make
sure you completely understand these instructions before you begin. When in doubt, seek
professional assistance. Be sure the cables will reach the unit and transducer location before
beginning installation. Please check the packing list above. If you are missing any items,
please contact your Garmin dealer. Be sure to wear safety goggles and dusk mask when drill-
ing and cutting.
Installing the Flush Mount Pocket
1. Using the supplied Mounting Template locate a suitable mounting location and
tape the template in place. Be sure to check behind the installation area to
avoid cutting or drilling into wiring, cables, etc.
2. Drill a 3/8” hole at the location in di cat ed on the template as a starting point,
then using the Jig Saw, cut the panel along the bold line. Be sure that your
initial cut does not go outside the line that in di cates the inside edge of the
pocket. (Figure 1)
3. Using a file or sandpaper, remove any burrs from the open ing. Test fit the Flush
Mount Pocket and make any ad just ments to correct the fit.
4. Install the two Foam Rubber Pads in the pocket at the locations indicated in
Figure 2. To install the pads, peel the lining off of the back and install with the
sticky side against the pocket.
5. Insert the pocket in the panel (The Garmin logo should be positioned at the
top.) Install a M4 Hex Head Screw through the pocket and the corresponding
hole in the Metal Retaining Bracket. Start a 4mm Hex Nut on the screw. Repeat
the process until all 4 nuts are started (Figure 3). Tighten the M4 nuts using a
7mm wrench or socket.
If operating in a high vibration environment it is recommended
that you use a thread locking compound on the M4 Hex Head Screws.
6. Secure the cable to the rectangular slot on the left side of the Flush Mount
Pocket or one of the metal retaining brack ets with the wire tie provided in the
kit. Leave approximately 18” of cable extending through the pocket to aid in
the installation and removal of the unit.
Figure 1
Flush Mount Pocket:
Mounts to the bulkhead
and retains the unit
Figure 2
Rubber Pad Location
M4 Machine Nut
Metal Retaining Bracket
Boat Panel
M45x40mm Hex Head
Tool List (Not Included)
Figure 3
Jig Saw Phillips Screwdriver
7mm Wrench Drill and 3/8’ Drill Bit
Masking Tape Thread Locking Compound — (Optional)
Safety Goggles and Dust Mask for drilling
E
A
B
C
D
Mounting Pocket
Side View
Wire Tie Slot
CUT ALONG BOLD LINE
CUT ALONG BOLD LINE
TRIM ALONG DASHED LINE
3/8"
DRILL A HO LE FOR
A PLACE T O BEGIN CUT T ING
INSIDE EDGE OF POCKET
Installing/Removing the Unit
1. Connect the wiring harness to the unit, making sure the locking ring is
fully tightened. (Figure 4)
2. Slide the Fishfinder into the pocket. When the Fishfinder is fully inserted,
it will click into place at the lock tabs (Figure 5). It may be necessary to
apply some pressure when inserting the assembly into the pocket to
compress the foam rubber pads.
3. To remove the unit from the pocket, press the lock tabs toward the unit
while sliding the unit out of the pocket. (Figure 6)
© 2003 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park In dus tri al Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00311-00 Rev. A
Figure 5 Figure 6
Figure 4
Lock Tabs
CUT ALONG BOLD LINE
CUT ALONG BOLD LINE
TRIM ALONG DASHED LINE
FLUSH MOUNT TEMPLATE
3/8"
DRILL A HOLE FOR
A PLACE TO BEGIN CUTTING
INSIDE EDGE OF POCKET
Garmin Ltd. or its subsidiaries Part Number 190-00311-00 Rev. A
Produktspezifikationen
| Marke: | Garmin |
| Kategorie: | Fischfinder |
| Modell: | Fishfinder 80 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Garmin Fishfinder 80 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Fischfinder Garmin
14 August 2024
29 Juli 2024
28 Juli 2024
25 Juli 2024
25 Juli 2024
24 Juli 2024
23 Juli 2024
23 Juli 2024
22 Juli 2024
19 Juli 2024
Bedienungsanleitung Fischfinder
- Fischfinder Humminbird
- Fischfinder Furuno
- Fischfinder Lowrance
- Fischfinder Simrad
- Fischfinder Lucky
- Fischfinder Eagle
- Fischfinder Raymarine
- Fischfinder Closer Pets
- Fischfinder Deeper
Neueste Bedienungsanleitung fĂĽr -Kategorien-
16 September 2024
6 September 2024
1 September 2024
22 August 2024
22 August 2024
21 August 2024
20 August 2024
19 August 2024
19 August 2024