Garmin Fishfinder 120 Bedienungsanleitung

Garmin Navigator Fishfinder 120

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Garmin Fishfinder 120 (2 Seiten) in der Kategorie Navigator. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Installation Instructions

Please read through these instructions thoroughly before attempting installation. Make sure

you completely understand these instructions before you begin. When in doubt, seek profes-

sional assistance. Be sure the wiring harness reaches the unit and transducer location before

beginning installation. The Garmin Fishﬁ nder 120 hardware allows for installation on either

the transom or trolling motor. Please check the packing list below. If you are missing any items,

please contact your Garmin dealer.

Fishﬁ nder 120

Selecting a Transom Mount Location

For your sonar to operate properly, the transducer has to be located in clean (non-

turbulent) water. The transducer should be mounted as near the center of the boat as

possible.

DO NOT cut the transducer lead, this will void your warranty and may cause the

unit to not operate at optimal levels.

DO NOT mount the transducer behind strakes, rivet lines, struts, ﬁ ttings, water

intake, discharge ports, eroding paint, or anything that creates air bubbles or causes the

water to become turbulent. It is important that the transducer be as close to the center

line as possible in calm, non-turbulent water for optimal performance. Avoid mounting

the transducer in locations where the boat may be supported during launching, haul-

ing, trailering, or storage.

Mount the transducer away from the path of the prop on single drive boats. On

twin drive boats, mount the transducer between the drives if possible. Do not mount

the transducer directly in the path of the prop. The transducer can cause cavitation that

may degrade the boat’s performance and damage the prop.

Testing the Transom Mount Installation

This test is to be performed after the unit installation. See unit operating instruc-

tions for additional use information. Since water is necessary to carry the sonar signal,

the Fishﬁ nder 120 does not function properly with the transducer out of the water.

When you place your boat in the water CHECK FOR LEAKS around the screw holes

that are below the water line. DO NOT leave your boat in the water for an extended

period of time without checking for leaks.

1. Begin testing the installation at a slow speed. If the sonar appears to be working

properly gradually increase the boat’s speed observing the sonar’s operation. If the

sonar signal suddenly is lost or the bottom return is severely degraded, note the

speed at which this occurs.

2. Return the boat to the speed the signal was lost. Make moderate turns in both

directions and see if the signal improves.

3. If the signal strength improves while turning, adjust the transducer so that it

extends another 1/8" below the transom of the boat. It may take several adjust-

ments to eliminate the degradation.

4. If the signal does not improve it may be necessary to move the transducer to a

different location.

Mounting the Transducer On a Trolling Motor

1. Slide the large Cable Tie through slot on the Transducer Mount with the ridges of

the band facing up until equal lengths extend on both sides of the mount. (For

cold water or heavy timber/debris areas, a metal 4-5” worm gear clamp is recom-

mended.)

2. Position the Mount Gasket on the curved top of the Mount.

3. Place the transducer assembly against the motor body of the trolling motor with the

front of the transducer pointed away from the trolling motor propeller.

4. Place the pointed end of Cable Tie through the fastener hole on the

opposite end and pull through (you will hear clicks) until snug.

5. Position the trans duc er so that it is parallel with the bottom

when in use. Make sure the Gasket is aligned properly. Pull

the Cable Tie end until tight. Excess may be trimmed off if

needed. Tighten the 10-32 locking nut until it touches the

mounting bracket and then tighten 1/4 turn more (do

not overtighten).

6. Route the 20’ (6.1 m) transducer cable using

the supplied cable ties to secure the cable

to the motor shaft. If desired, the forward-

facing portion (except the Cable Tie pocket)

of the Transducer Mount may be filled with

sealant to avoid debris accumulation.

Make sure the transducer is below

water level when the boat is on plane

at high speed.

Apply marine sealant to all screw

threads to prevent water from

seeping into the transom.

Mount the transducer parallel with the

water line.

Packing List:

A - Fishﬁ nder 120 Sonar Unit (1)

B - Swivel Mount Bracket (1)

C - Swivel Base (1)

D - Mounting Knobs- Short (1), Long (1)

E - Mounting Knob Spacer (1)

F - Transducer With Power Cable (1)

G - Transducer Mount (1)

H - Trolling Motor Mount Gasket (1)

I - 5 mm Flat Washers (2)

J - 5 x 30 mm Screws (2)

K - 10-32 Lock Nut (1)

L - 4 x 12 mm Screws (4)

M - 10-32 x 1.75 Screw (1)

N - 1/4” Cable Clamps (2)

O - Plastic Spacer (1)

P - 1/4” Rubber Washer (1)

Q - Cable Tie, 5.6” (4)

R - Cable Tie, 20” (1)

S - Snap-Ring (1)

(Cable not shown)

Assembling the Transducer

1. Insert the Rubber Washer and Plastic Spacer

in the transducer at the same time. DO NOT

lubricate the Rubber Washer.

2. Route the cable towards the back and

slide the transducer into the mounting bracket.

3. Place a 5 mm Flat Washer on the 10-32 x

1.75" screw and insert the screw through

the Mounting Bracket, Spacer, and Rubber

Washer.

4. Place the remaining 5 mm Flat Washer on

the exposed end and install the 10-32

Lock Nut finger tight. The transducer is

tightened further after installation on boat.

Mounting the Transducer On a Transom

Tool List (not included) - Drill, 3/8" Wrench or Socket, 5/32" and 1/8" Drill Bits,

Masking Tape, #2 Phillips Screw Driver, Marine Sealant

1. Position the transom mount at the selected location, making sure the transducer is

parallel with the water line. Mark the center locations of each hole on the transom

mount. (See figures to the right.)

2. Using the 5/32" bit, drill the pilot holes approximately 1" (25 mm) deep at the

marked lo ca tions. To avoid drilling the holes too deep, wrap a piece of tape around

the bit 1" from the point of the bit.

3. Apply Marine Sealant to the 5 x 30 mm screws. Attach the transducer to the transom

using the 5 x 30 mm screws. Adjust the transducer to extend beyond the bottom

of the transom approximately 1/8" (3 mm) on fiberglass hulls or 3/8" (10 mm) on

aluminum hulls. Adjust the transducer to be aligned parallel with the water.

5. Tighten the 10-32 locking nut until it touches the mounting bracket and then

tighten 1/4 turn more (do not overtighten).

6. Place the first cable clamp on the transducer cable approximately one third of the

distance between the transducer and the top of the transom. Mark the location.

Using a 1/8" bit, drill a pilot hole approximately 3/8" (10 mm) deep.

7. Attach the cable clamp using a 4 x 12 mm screw. Coat the screw with marine seal-

ant before installation. Repeat steps 6 and 7 using the other cable clamp.

8. Route the transducer cable as needed to the sonar unit. DO NOT CUT THE CABLE.

Try to avoid routing the cable with electrical wires or other sources of electrical

interference.

Level

Drill Pilot Holes Here

Vertical

Bottom of Transom

Align with transom

bottom. Transducer should

extend 1/8” below fiber-

glass hulls or 3/8” below

aluminum hulls.

Keep Parallel With Water Line

Installing the Unit On the Mounting Bracket

1. Align the slot on the back of the unit with the long mounting knob and slide in

place. It may be necessary to adjust the long knob to spread the bracket arms

apart. (Turn counter-clockwise to widen the bracket arms, clockwise to tighten.)

2. Adjust the unit angle and tighten the long mounting knob until snug.

3. Tilt the unit by loosening the long knob on the right side of the bracket assembly.

4. Rotate the entire bracket by twisting it left or right. (You will hear clicks as you turn

the bracket.)

5. Tighten all knobs once the desired viewing angle is obtained.

Unit Installation — Selecting a Proper Location

Choose a location that provides optimal viewing while operating the vessel and

allows easy access to the unit’s keypad. Select a mounting surface strong enough to

support the weight of the unit and protect it from excessive vibration or shock. DO

NOT mount the bracket in a location where the unit is exposed to extreme tempera-

ture conditions. When installing the mounting bracket, be sure to allow room for the

connection/routing of the power cable.

Mounting the Bracket Assembly

Tool List (not included) - Drill, Screwdriver (Phillips or Standard), three #8 pan head

machine bolts with matching nuts and washers and a 5/32” drill bit, OR three #8 pan

head self-tapping screws and a 1/16” drill bit

1. Using the swivel base as a template, mark the location of the three holes which

are used to secure the bracket to the mounting surface.

2. If securing the base with machine bolts, drill three 5/32” holes at the locations

you marked. OR, If securing the base using self-tapping

screws, drill 1/16” starter holes at the locations you

marked. Starter holes should generally be no deeper

than half the screw length.

3. Secure the swivel base with three bolts or screws.

DO NOT OVERTIGHTEN.

4. Place the rest of the mount over the swivel base

and secure with the short knob.

Wiring Harness Installation

The Fishfinder 120 comes with a wiring harness that connects the unit to power and

the transducer with one easy-to-remove connection. If it is necessary to extend the power

wires, use 22 AWG wire. DO NOT cut the transducer cable. This will void your warranty.

If your boat has an electrical system, it may be possible to wire the unit directly to an

unused holder on your current fuse block. If you are using the boat’s fuse block, remove

the in-line fuse holder supplied with the unit. You may also wire the unit direct to the

battery. DO NOT CAUTION: The Fishfinder 120 input voltage is 10-18 volts DC.

exceed this voltage as this may damage the unit and void the warranty.

Installing the Wiring Harness:

1. Determine the polarity of the power source using a Test Light or Volt Meter.

2. Install the Red (+) wire on the Positive fuse holder or battery terminal.

3. Install the Black (-) wire on the Negative fuse holder or battery terminal.

4. Install a 2 amp fuse in the fuse holder (fuse block only).

5. Align the notches on the cable plug and back of the unit. Insert the cable into the

connector and turn the lock ring counter-clockwise unit it stops.

Unit Care

Cleaning - Clean the unit housing using a cloth lightly dampened with a mild detergent

solution and then wipe dry. Avoid chemical cleaners and solvents that may damage plas-

tic components. Do not apply cleaner to electrical contacts on the back of the unit.

Storage - Do not store the unit where exposure to temperature extremes may occur, as

permanent damage may result.

Do not mount the transducer behind strakes,

rivet lines, struts, fittings, water intakes, or

discharge ports.

Setup Menu — Alarms: Battery

Sounds an alarm when the battery is reaching a critical state of discharge.

Setup Menu — Alarms: Shallow/Deep Water Alarm

‘Shallow’ and ‘Deep’ can be set to sound a shallow/deep water warning at a depth

determined by you. (If the either alarm is set and ‘Depth’ units are changed, both alarms

default to ‘Off’.) These alarms may be set to ‘Off’

(default) or from 1-600 ft.

Setup Menu — Alarms: Fish Alarm

Sounds an alarm when the unit detects what it determines to be a ﬁ sh. The alarm

selections are: ‘Off’ (default) or ‘On’.

Setup Menu — Graph: Fish ID

Determines how the graph displays underwater targets and background informa-

tion. If ‘Fish ID’ is set to ‘Off’, the unit displays all of the available information about

the underwater environment. If a fish symbol is selected, the graph displays only the

information related to that symbol (large, medium and small sizes).

— All available information is displayed. (default)

— Suspended targets displayed as symbols. No background information is

displayed in this mode.

— Same as above with target depth displayed.

— Suspended targets display as symbols. In this mode background

information is still displayed making ﬁ sh identiﬁ cation easier.

— Same as above with target depth displayed.

Limited Warranty

This Garmin product is warranted to be free from defects in materials or workmanship for one year from

the date of purchase. Within this period, Garmin will at its sole option, repair or replace any components

that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or

labor, provided that the customer shall be responsible for any transportation cost. This warranty does not

cover failures due to abuse, misuse, accident or unauthorized alteration or repairs.

THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL

OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING

UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH

MAY VARY FROM STATE TO STATE.

IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CON-

SEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE

THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the exclusion of

incidental or consequential damages, so the above limitations may not apply to you.

Garmin retains the exclusive right to repair or replace the unit or software or offer a full refund of the

purchase price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY

FOR ANY BREACH OF WARRANTY. Products sold through online auctions are not eligible for rebates or

other special offers from Garmin. Online auction confirmations are not accepted for warranty verification.

To obtain warranty service, an original or copy of the sales receipt from the original retailer is required.

Garmin will not replace missing components from any package purchased through an online auction.

To obtain warranty service, contact your local Garmin authorized dealer. Or call Garmin Customer

Service for shipping instructions and a RMA tracking number. The unit should be securely packed with

the tracking number clearly written on the outside of the package. The unit should then be sent, freight

charges prepaid, to any Garmin warranty service station. A copy of the original sales receipt is required as

the proof of purchase for warranty repairs.

The Fishﬁ nder 120 has no user-serviceable parts and is fastened shut with screws. Any attempt to open

the case to change or modify the unit in any way will void your warranty and may result in permanent

damage to the equipment.

Software License Agreement

By using the Fishﬁ nder 120, you agree to be bound by the terms and conditions of the following soft-

ware license agreement. Please read this agreement carefully.

Garmin grants you a limited license to use the software embedded in this device (the “Software”) in

binary executable form in the normal operation of the product. Title, ownership rights and intellectual

property rights in and to the Software remain in Garmin.

You acknowledge that the Software is the property of Garmin and is protected under the United States of

America copyright laws and international copyright treaties. You further acknowledge that the structure,

organization and code of the Software are valuable trade secrets of Garmin and that the Software in

source code form remains a valuable trade secret of Garmin. You agree not to decompile, disassemble,

modify, reverse assemble, reverse engineer or reduce to human readable form the Software or any part

thereof or create any derivative works based on the Software. You agree not to export or re-export the

Software to any country in violation of the export control laws of the United States of America

GARMIN

, DCG

and See-Thru

are registered trademarks of Garmin Ltd. or its subsidiaries

and may not be used without the express permission of GARMIN.

Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.

Tel.913/397.8200 Fax. 913/397.8282

Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51

9DL, U.K. Tel. 44/1794.519944 Fax.44/1794.519222

Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan

Tel. 886/2.2642.9199 Fax. 886/2.2642.9099

www.garmin.com Part Number 190-00306-00 Rev. A

Operational Instructions

Thank you for choosing the Garmin Fishﬁ nder 120. This product is designed for

easy operation and to provide years of reliable service. Please read through these instruc-

tions to get the most out of your new unit. If you encounter a problem please contact

our Product Support Department at 913-397-8200, Monday - Friday 8:00 a.m. to 5:00

p.m. CST or on the internet at www.garmin.com/support.

Speciﬁ cations

Case: Fully Gasketed, high-impact plastic alloy

Display: 3.1”H x 3.2”W (7.9 x 8.1 cm), 240 x 128 pixels

Size: 6.1” W x 4.9” H x 2.6 D (15.5 x 12.5 x 6.6 cm); Weight: 18.7 oz.

Temperature Range: +5° to 158°F (-15C to 70C)

Waterproof: IEC 529, level IPX-7 (submerged to 1 meter for 30 minutes)

Internal memory backup to retain user settings

Input: 10 to 18 Vdc w/ high voltage protection

Usage: 8 watts maximum, Nominal: 12 Vdc @ 0.5 amps

Sonar Power Output: 100 watts (RMS), 800 watts (peak to peak)

Frequency: 200kHz

Depth: 600 foot max depth (Depth capacity is dependent on water salinity, bottom type and other

water conditions.)

Speciﬁ cations subject to change without notice.

Fishﬁ nder 120

The Fishfinder 120 is able to display a variety of useful information about the

underwater environment. Below are a few things the unit helps you see.

Water Depth

The unit displays water depth and can provide a warning

when a specific depth is encountered. The Depth

Scale is displayed from top to bottom along the

right side of the display. Messages and Alarm

Icons are displayed along the bottom.

Water Temperature

The unit displays the water temperature at the

transducer.

Fish

The unit displays fish as arches or fish symbols in

3 sizes and can alert you when a fish is detected.

Thermocline and Structure

GARMIN’s See-Thru® technology can display

more than just the thermocline and structure, the

unit displays fish in and below the thermocline,

trees, brush, and deadfall.

Bottom Shape and Type

Garmin’s unique DCG® (Depth Control Gain) system provides

a clear graphic representation of the bottom type and its shape.

ARROW KEYS

The UP DOWN ARROWand keys are used to

select items on the Adjustment Menu and Setup

menu. The LEFT and RIGHT ARROW keys are

used to quickly cycle through Adjustment Menu

settings.

ENTER Key

The key is used to activate/deactivate ENTER

the Adjustment Menu and Setup Menu data

fields for review or changes.

MENU Key

The key is used to activate/deactivate MENU

Adjustment and Setup Menus.

POWER Key

The Key is used to turn the unit on/off POWER

and to activate the display backlight. Press and

hold to turn the unit on/off. Press briefly and

release to activate the backlight. To change the

backlight level, press the key repeat-POWER

edly to cycle between Off, Low and High.

Adjustment Menu — Range

Sets the display depth range. The unit can be set to automatically track the

bottom or set to a user-specified range. Available settings are: ‘Auto’ (default) and

15-600 ft.

Adjustment Menu — Gain

Controls the sensitivity of the unit’s sonar receiver. This provides some flexibility

in what is seen on the display. To see more detail, increase the receiver sensitivity by

selecting a higher gain (+). If there is too much detail or if the screen is cluttered,

lowering the sensitivity (-) may increase the clarity of the display. Available settings

are: ‘Normal’ ( default) and +5 to -5.

Adjustment Menu — Scroll

Adjusts the rate that the graph scrolls from right to left. If you are sitting still or the

graph is moving too fast, slowing or pausing the graph can be beneﬁ cial.

Adjustment Menu — Zoom

Selects a display zoom scale. Available settings are: ‘OFF’ (default), ‘2X’ and ‘4X’

zoom.

Adjustment Menu — View

‘View’ is available only when a Zoom scale other than ‘OFF’ is selected. This set-

ting allows you to select a specific zoom area to view on the display or allow the unit

to automatically select a zoomed viewing area based on the bottom. When adjusting

this setting, the top and bottom numbers reflect the zoomed view depth range.

Using the Adjustment Menu

The Adjustment Menu allows direct access to the

settings most commonly changed while using the unit.

These include the depth Range, Gain, Zoom, and the

View settings. Current Adjustment Menu settings may

be viewed by pressing the key. Press MENU MENU

again to hide the window or to exit any window. The

current adjustment option always displays in the

upper left of the display. Press or on the LEFT RIGHT

ARROW keys to scroll through the available options.

To immediately change the current adjustment option, press the or UP DOWN

ARROW key. If you wish to review the available settings before making a change,

press the key to activate the adjustment window.ENTER

To change a setting on the unit:

1. Press MENU, then using the or UP DOWN ARROW key, move the selection arrow

to the desired option and press . Choose ‘Setup’ for the main Setup Menu.ENTER

2. Using the UP or DOWN ARROW key move the selection arrow to the desired

setting and press . (The selection arrow wraps when you reach the end of ENTER

a menu and adjustment window. If holding the key down, release then ARROW

press.) Holding down on an key rapidly advances the selection speed.ARROW

3. To close a setting or menu window, press .MENU

Setup Menu — Graph: Whiteline

Controls how the unit displays information about the bottom type (hard or

soft). With Whiteline ‘Off’, the bottom return displays as solid black and contains no

information on bottom hardness. With Whiteline ‘On’, the bottom return becomes

a grayscale pattern and can be used to determine bottom hardness. A hard bottom

returns a stronger signal and displays a thicker bottom layer. A weaker (soft) bottom

return displays a thinner bottom layer. The selections are: ‘Off’ or ‘On’ (default).

Setup Menu — Graph: Noise Reject

Filters unwanted noise from the graph (especially when moving at faster speeds)

and can be turned ‘Off’ or set to a ﬁ xed value from 1-100%. Remember when setting the

‘Noise Reject’, the higher the noise rejection setting, the more likely the unit does not

show ﬁ sh or structure. The selections are: 1-100% (default 50%) or ‘Off’.

Setup Menu — Numbers: Size

Displays either ‘Normal’ (default) or ‘Large’ depth, temp. and battery numbers.

Setup Menu — Numbers: Battery

Choose to either ‘Hide’ (default) or ‘Show’ the current battery voltage.

Setup Menu — Numbers: Water Temp.

‘Water Temp’ automatically displays when set to ‘Auto’ (default) or you may choose

to ‘Hide’ the temperature numbers. Water temperature will only display if you have a

temperature capable transducer.

Setup Menu — Units: Depth

Choose to display measurements in Feet (ft, default), Meters (m) or Fathoms (fa). (If

the ‘Depth Alarm’ is set when ‘Units’ are changed, the ‘Depth Alarm’ is defaulted to ‘Off’)

Setup Menu — Units: Temperature

Choose to display the water temperature in Fahrenheit (°F, default) or Celsius (°C)

Setup Menu — System: Simulator

The Fishfinder 120 comes with a built-in simulator mode that allows you to

practice and learn the operation of the unit at home rather than on the water. The

unit indicates that it is running the simulator mode by displaying a message in the

lower left of the display. While in the simulator mode, the unit displays a random

bottom scene and the Fishfinder 120 can be controlled (except Noise Reject and

Gain) just as if it were on the water. To exit the Simulator, turn the unit off. If no

keys are pressed for 2 minutes, the unit automatically resets to default unit settings

while in simulator mode. If the unit does not detect a transducer attached, it auto-

matically starts in Simulator mode.

Setup Menu — System: Contrast

Adjusts to compensate for different light levels or viewing angles.

Setup Menu — System: Defaults

This option allows you to restore the factory default settings for the unit.

Understanding Sonar

To understand what the unit is displaying, it is important to have a general knowl-

edge of how the unit works and how it determines what to display. The unit operates by

transmitting sound waves toward the bottom of a lake, stream, or seabed in a cone shaped

pattern. The area covered by the transmitted sound waves is determined by the cone

angle of the transducer and the water depth. Using

Garmin’s standard 20° transducer, the coverage is

approximately 1/3rd of the water depth. The coverage

area at a 30-foot depth is approximately a 10-foot

diameter circle.

When a transmitted soundwave strikes an

underwater object, sound is reflected back to the

transducer. The transducer collects the reflected sound

waves and sends the data to the unit to be processed

and displayed on the graph. The underwater data is

displayed on the graph in the order that it is returned:

first returned—first on the graph. Generally speaking,

if the only thing between the transducer and the

bottom is water, the first strong return comes from

the bottom directly below the transducer. The first

strong return sets the bottom level. Weaker secondary

returns provide the detailed data. A ﬁ sh may be in the

coverage area of the transducer, but remember the ﬁ rst

strong return sets the bottom level. Any ﬁ sh in a Dead

Zone is not detected by the sonar. The

ﬁ sh is never detected since the bottom

level is never set below the ﬁ sh. The

ﬁ sh on the right side of the display

(shown in light grey) is detected and

displayed when the transducer cone

passes over the ﬁ sh.

It is important to understand that

the unit does not display a 3-D repre-

sentation of the underwater environ-

ment. The unit can display multiple

things (such as a ﬁ sh and a tree) at

the same time but can not determine

where the return originated, only when

it was received. Remember that the

Fishﬁ nder displays a 2-D picture of the

underwater environment. A ﬁ sh and an

underwater structure could be located

anywhere in the coverage area at that

slice of time.

10'

12'

15'

18'

21'

24'

27'

30'

(Simulated display)

Warning: This product, its packaging, and its components contain chemicals known to the State

of California to cause cancer, birth defects, or reproductive harm. This Notice is being provided

in accordance with California’s Proposition 65. If you have any questions or would like additional

information, please refer to our web site at www.garmin.com/prop65.

Dead Zone

Produktspezifikationen

Marke:	Garmin
Kategorie:	Navigator
Modell:	Fishfinder 120

Brauchst du Hilfe?

Wenn Sie Hilfe mit Garmin Fishfinder 120 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Navigator Garmin

Garmin nuvi 1210T Bedienungsanleitung

2 Oktober 2024

Garmin ECHOMAP UHD 75cv Bedienungsanleitung

1 Oktober 2024

Garmin Dash Cam X210 Bedienungsanleitung

25 September 2024

Garmin Dash Cam X310 Bedienungsanleitung

25 September 2024

Garmin Dash Cam X110 Bedienungsanleitung

25 September 2024

Garmin nüvi 3597LMTHD Bedienungsanleitung

18 September 2024

Garmin nuvi 2757LMT Bedienungsanleitung

18 September 2024

Garmin DriveLuxe 51 LMT-S Bedienungsanleitung

16 September 2024

Garmin Nüvi 2448 Bedienungsanleitung

15 September 2024

Garmin Zumo 350LM Bedienungsanleitung

13 September 2024

Bedienungsanleitung Navigator

Neueste Bedienungsanleitung für -Kategorien-

TomTom VIA 1510 Bedienungsanleitung

14 Oktober 2024

Sanyo NVM-4030 Bedienungsanleitung

14 Oktober 2024

TomTom GO 950 Bedienungsanleitung

14 Oktober 2024

TomTom Start 52 Bedienungsanleitung

12 Oktober 2024

TomTom GO 7000 Bedienungsanleitung

12 Oktober 2024

Pioneer NavGate Head-Up SPX-HUD01 Bedienungsanleitung

9 Oktober 2024

TomTom Toyota TNS400 Bedienungsanleitung

9 Oktober 2024

TomTom Start 20 Bedienungsanleitung

8 Oktober 2024

Alpine X903D-V447 Bedienungsanleitung

8 Oktober 2024

Alpine X903D-F Bedienungsanleitung

7 Oktober 2024