Frigidaire GHWQ125WD1 Bedienungsanleitung

Frigidaire Klimaanlage GHWQ125WD1

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Frigidaire GHWQ125WD1 (32 Seiten) in der Kategorie Klimaanlage. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/32
READ BEFORE INSTALLING UNIT
Compact Window Mounting (8,000~12,000 BTU)
Installation Instructions
Phillips Screwdriver
TOOLS NEEDED
Level
Flat Head Screwdriver
Pencil
Ruler or tape measure
Scissors or knife
Drill and 1/8” drill bit ((If pilot holes are needed)
Proper PPE
NOTE:
Mounting Hardware Qty.
16120300A29215
1
* Extra hardware provided in separate bag.
Short Right Extension Arm
(For 22”-26” windows)
1
Cotter Pin 2*
Open Window Bracket – RH 1
Main Support Pin 2*
Long Right Extension Arm
(For 26”-36” windows)
1
1
Main Support Bracket
1/2” Type B Screw 2*
2*
3*
1/4” Type B Screw
1/2” Type A Screw
1” Type A Screw 2*
Window Sash Foam
Window Sealing Foam
Bracket Sealing Foam
Additional Side Arm Foam 2
1
1
1
Extra hardware pack* 1
Side Arm Foam 2
Mounting Accessories Qty.
INSTALLATION WARNINGS AND CAUTION
Window Sash Lock 1
1Open Window Bracket – LH
The unit is for window mounting only.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
SAVE CARTON and these INSTALLATION
INSTRUCTIONS for future reference. The carton is
the best way to store unit during winter, or when not
in use.
DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE.
Check window opening size:
Your air conditioner is designed to be installed in standard double hung windows with opening widths of 23.6 to 36
inches (599mm to 914 mm)
Lower sash must open sufficiently to allow for a clear vertical opening of 13.8 inches (350 mm).
Bracket instruction:
There should be at least 11.8 inches (300mm) of clearance around the unit.
Installation Instructions
2
(350 mm)
Wooden Windows
23.6" to 36"
599mm to 914mm
OFFSET
EXTERIOR
WALL
INNER
WINDOW SILL
INTERIOR
WALL
13.8" min
OFFSET
Vinyl-Clad Windows
INNER
WINDOW SILL
23.6" to 36"
EXTERIOR
WALL
INTERIOR
WALL
599mm to 914mm
13.8" min
(350 mm)
Rear Cross Brace Main Support Bracket
Angled Support Arms
Left Extension
Arm
Spring Push Pin
Right Extension
Arm
Horizontal Bracket
Indoor side
Outdoor side
11.8" min
(300 mm) 11.8" min
(300 mm)
11.8" min
(300 mm)
11.8" min
(300 mm)
FIG. 1C
11.8" min
(300 mm)
11.8" min
(300 mm)
11.8" min (300 mm) 11.8" min (300 mm)
11.8" min (300 mm)
FIG. 1B
11.8" min (300 mm)
Outdoor side Indoor side
1
3
5
7
9
11
13
15
17
19
1
3
5
7
9
11
13
15
17
19
1
3
5
7
9
11
13
15
17
19
1
3
5
7
9
11
13
15
17
19
Install the Bracket:
1. Place bracket in the window as shown below.
Installation Instructions
3
1. Measure your window width on the inside of your sill, at
the widest part. For window widths between 22 " use "-26
short right extension arm. For window widths between
26"-36" use long right extension arm.
2. Install the right extension arm and adjust by pressing
the spring push pin to reach the center mark in the middle
of the window.
Set up the Bracket:
Adjust
Center mark
Adjust
NOTE: The bracket will be offset to the left when centered.
2. Check if the center mark of the bracket is in the middle
of the window. Make adjustments if needed.
3. Fix the bracket as shown below:
For Wooden Windows
Secure bracket to windowsill by drilling 1/8 pilot holes "
and installing 1/2 Type A screws on extension arms as "
shown below.
INSIDE OUTSIDE
For Vinyl-Clad Windows
Vinyl Lip
1/2" Type A 1/2" Type A
For Vinyl-Clad Windows
Secure bracket to windowsill by drilling 1/8 pilot holes "
and installing 1/2 and 1 Type A screws on extension " "
arms as shown below.
1" Type A 1" Type A
1/2" Type A1/2" Type A
For Wooden Windows
INSIDE
OUTSIDE


Produktspezifikationen

Marke: Frigidaire
Kategorie: Klimaanlage
Modell: GHWQ125WD1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Frigidaire GHWQ125WD1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Klimaanlage Frigidaire

Bedienungsanleitung Klimaanlage

Neueste Bedienungsanleitung fĂĽr -Kategorien-