Focal FDP 4.600 Bedienungsanleitung

Focal Empfänger FDP 4.600

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Focal FDP 4.600 (8 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/8
1
POWER PER CHANNEL:
• 4 x 150 wRMS @ 4ohms
• 4 x 200 wRMS @ 2ohms
• 2 x 400 wRMS (Bridged @ 4ohms)
ROUTE SWITCH
• 1+2 = All four RCA inputs are used.
• 3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter
on all four channels.
Recommended when bridging channels 1, 2, 3, 4.
The level controls still function.
• Copy = Input signal and filters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band
pass filter on all four channels.
Recommended when bridging channels 1,2,3,4.
The level controls still function.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass Filter for a midbass or tweeter.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass filter.
• LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
• MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2
will also be mono subwoofer and the remote volume control will control level.
The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.
If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP 4.600 : FOUR CHANNEL AMPLIFIER
Operation / Configuration
2
RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL.
• The amplifier control has sufficient adjustment range for both low level and high level input into the RCA LEVEL
jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers,
can be directly connected to the RCA jacks when the amplifier control is adjusted to 8V.LEVEL
SETTING LEVEL
• Set the amplifier control to minimum before you turn on the amplifier for the first time.LEVEL
• For lowest distortion and lowest noise the amplifier should be set at the lowest setting that yields LEVEL
sufficient loudness without distortion. For lowest noise your source radio volume control should be near
maximum that does not cause distortion.
• To find the best amplifier setting: LEVEL
With the amplifier at minimum, slowly increase the source radio volume to around 3/4 without distortion. LEVEL
Then, slowly turn up the amplifier control to the maximum desired loudness. Listen very carefully and LEVEL
turn down the amplifier control if you hear any distortion.LEVEL
FPD 600.4 CONFIGURATION EXAMPLES
4 CHANNEL STEREO NON-BRIDGED
• (SEE GRAPHIC B1)
• If you have four input wires from the source deck, plug them into inputs 1+2 and 3+4.
Set ROUTE switch to 1+2.
• If you have two input wires from the source deck, plug them into inputs 3+4.
Set ROUTE switch to 3+4.
Set the switch to STEREO.
• If you are NOT using a subwoofer set all switches to flat. If you hear distortion in your woofers set all switch to
HP and adjust all HP frequency until the distortion goes away, this will probably be around 50 Hz to 70 Hz.
RADIO FLAT or HP50Hz
1+250Hz FLAT or HP
STEREO
B1
XOVER
XOVER XOVER
XOVER
B1 <GRAPHIC of Source Radio to input channel 1+2, 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, 3+4>
3
IF YOU ARE USING TWO SUBWOOFERS:
• (SEE GRAPHIC B2)
• Put your woofer/tweeters on channel 1+2.
Set 1+2 switch to HP.
Adjust 1+2 HP frequency to 50 Hz.
• Subwoofers on channel 3+4.
Set 3+4 switch to LP/BP.
Set 3+4 switch to LP.
Adjust 3+4 LP frequency to 50 Hz.
Set the switch to MONO.
Plug in the remote sub control.
RADIO LP LP/BP50Hz
3+450Hz HP
MONO
B2
+ –
SUBWOOFER
+ –
SUBWOOFER
REMOTE SUB CONTROL
XOVER
XOVER
B2 <GRAPHIC of Source Radio to input channel 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, one

Produktspezifikationen

Marke: Focal
Kategorie: Empfänger
Modell: FDP 4.600

Brauchst du Hilfe?

Wenn Sie Hilfe mit Focal FDP 4.600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Focal

Focal

Focal FDP 1.900V2 Bedienungsanleitung

28 August 2024
Focal

Focal R-4280 Bedienungsanleitung

21 August 2024
Focal

Focal Impulse 4.320 Bedienungsanleitung

21 August 2024
Focal

Focal FPX 1.100 Bedienungsanleitung

21 August 2024
Focal

Focal FDP 1.900 Bedienungsanleitung

21 August 2024
Focal

Focal FDP 6.900 Bedienungsanleitung

20 August 2024
Focal

Focal FDP 6.900 V2 Bedienungsanleitung

20 August 2024
Focal

Focal FDS 2.350 Bedienungsanleitung

20 August 2024
Focal

Focal FPS 2160 Bedienungsanleitung

20 August 2024
Focal

Focal FDP 1.2000 Bedienungsanleitung

19 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024