Fender BXR 25 Bedienungsanleitung
Fender
Gitarrenverstärker
BXR 25
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fender BXR 25 (4 Seiten) in der Kategorie Gitarrenverstärker. Dieser Bedienungsanleitung war für 20 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
T H E S O U N T H A T C R E A T E S L E G E N D SD
P/N 047999
Owner,s Manual
BXR 25
The Fender BXR
25
amplifier is the most recent effort in
state-of-the-art bass amplifier technology. The Fender design
team developed the BXR
25
with the assistance from some of
today’s best musicians. It represents years of decisions
concerning performance, features, and specifications. The
features included in the BXR
25
make it a viable and tough
competitor, whether meeting the demands of a serious
practice session, or just jammin’!
The preamp section of the BXR 25 features two inputs of
differing sensitivity, that allow connection of a variety of
signal sources and levels. Built-in emphasis circuitry is
included to provide enhancement of the extreme low and high
ends of the frequency spectrum. Wide range active “HIGH”,
‘MID”, and “LOW” controls allow further response tailoring
of the high, mid, and low frequency areas of the sounds you
and your instrument produce. The rugged 25 Watt power
amplifier was designed to give years of reliable service under
all conditions and is equipped with a unique implementation
of our exclusive DELTACOMP™ adaptive compression
system. When DELTACOMP™ engages, it is practically
impossible to cause the power amplifier to clip (distort). With
DELTACOMP™, apparent compressor release time is kept
short, yet waveform distortion is kept to a minimum at low
frequencies.
A number of professional features have been added to the
BXR
25
like PREAMP OUT & POWER AMP IN jacks which
can be used as an Effects Loop. The PREAMP OUT is
connected to the input of your effect (digital delay or other
effects device) and the output from the effect is returned to the
POWER AMP IN. The PREAMP OUT can also be used to
connect your BXR
25
directly to a recording console or sound
reinforcement mixer. The HEADPHONE jack automatically
mutes the speaker in addition to driving Stereo or Mono
headphones.
The selection of a Fender amplifier will reward you with years
of quality music in a wide range of sonic possibilities. This
manual is designed to familiarize you with the features and
functions of your BXR
25
amplifier. Read this manual carefully
so you will benefit from these features as soon as you start
using your new Fender amplifier.
The built-in quality of a Fender amplifier is the result of over
four decades of dedication in the combined skills of the
Fender design team.
That’s why we proudly say ..............FENDER,
The Sound
That Creates Legends.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE UNIT TO RAIN OR MOISTURE.
BXR 25
BXR 25 FRONT PANEL FUNCTIONS
REAR PANEL DESCRIPTION
G. TAPE INPUTS: Plug-in connection for any line level
(500mV) stereo or mono signal. This signal is mixed into
the power amp along with the instrument signal from the
preamp. It has fixed gain and is unaffected by any of the
front panel controls; however, the signal will be affected
by any device inserted between the preamp output and
the power amp input. It is useful for patching in a CD, tape
player, rhythm machine or other signal source to be used
as accompaniment for practice or performance. The
output level control of the external signal source is used to
control its own volume while the front panel volume control
is used for the instrument in order to obtain a balance.
H. PREAMP OUT: This jack provides an unbalanced output
signal from the preamp. This output can be used in
conjunction with the POWER AMP IN as a patch point for
external mono effects devices.
I. POWER AMP IN: This unbalanced jack inputs signal
directly to the power amp section. It automatically
disconnects the preamp circuitry when used. This is useful
when using the patch point option or when using the BXR
25 as a slave amplifier for an external signal source.
J. HEADPHONES: This jack provides an output to standard
stereo or mono headphones for private listening. NOTE:
Use of this jack automatically disables the main speaker.
CAUTION: Prolonged listening at high levels may be
hazardous to your hearing!
K. POWER INDICATOR: When this LED is illuminated, the BXR
25 is receiving power.
L. POWER: Turns the BXR 25 on or off.
The front panel contains all items necessary for system
operation and observation. Please read this section of the
manual carefully to make sure you understand all the
operational features of your new FENDER BXR 25
amplifier.
A. Input 1: High gain
B. Input 2: Low gain
The high gain input (INPUT 1 ) should be used for most
instruments. This input can handle as much as 3.5 volts
R.M.S., while the low gain input (INPUT 2) accepts 7 volts
R.M.S. without audible distortion. For both cases, this is
greater than any active bass with a 9 volt battery can
produce. If you are using a bass with dual 9 volt batteries
or a "hot" passive bass, it might be wise to try INPUT 2.
For the rare case where two players want to use one
amplifier or where two instruments are to be used during
the performance, both inputs may be used.
C. VOLUME: This control sets the gain of the preamp and
serves as an adjustment for the "loudness" of the amplifier.
D. LOW: adjusts the low frequency part of the spectrum, the
area where the "deep” fundamentals reside.
E. MID: adjusts the mid frequency part of the spectrum.
Turning the mid down will cause the sound to become
"TIGHT" or more "PUNCHY."
F. HIGH: adjusts the high frequency part of the spectrum.
Turning the HIGH up will cause the sound to become
"BRIGHT" or more "CRISP".
INPUT POWER: This tells you how much AC power (75 Watts)
the amplifier can "draw" from the wall socket when the
amplifier is at full power. The marking directly below tells you
what the the wall socket Voltage and Frequency must be.
Incorrect line voltage will damage your amplifier and VOID
THE WARRANTY.
LINE CORD: The line cord should be connected to a suitable
power source, with the correct voltage and frequency, as
shown in the INPUT POWER at the amplifier rear. If you are
not sure, check some other piece of equipment in your area.
DO NOT ALTER THE AC PLUG.
Produktspezifikationen
| Marke: | Fender |
| Kategorie: | Gitarrenverstärker |
| Modell: | BXR 25 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Fender BXR 25 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Gitarrenverstärker Fender
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
Bedienungsanleitung Gitarrenverstärker
- Gitarrenverstärker Valeton
- Gitarrenverstärker Roland
- Gitarrenverstärker Vox
- Gitarrenverstärker Yamaha
- Gitarrenverstärker Marshall
- Gitarrenverstärker Peavey
- Gitarrenverstärker Behringer
- Gitarrenverstärker Boss
- Gitarrenverstärker Line 6
- Gitarrenverstärker Radial Engineering
- Gitarrenverstärker Hartke
- Gitarrenverstärker ART
- Gitarrenverstärker Orange
- Gitarrenverstärker Harley Benton
- Gitarrenverstärker Electro Harmonix
- Gitarrenverstärker Blackstar
- Gitarrenverstärker Bugera
- Gitarrenverstärker TC Electronic
- Gitarrenverstärker Palmer
- Gitarrenverstärker Ampeg
- Gitarrenverstärker Laney
- Gitarrenverstärker SPL
- Gitarrenverstärker Ashdown Engineering
- Gitarrenverstärker Suhr
- Gitarrenverstärker AER
- Gitarrenverstärker Markbass
- Gitarrenverstärker EBS
- Gitarrenverstärker Fishman
- Gitarrenverstärker Voodoo Lab
- Gitarrenverstärker GR Bass
- Gitarrenverstärker Two Notes
- Gitarrenverstärker Hughes & Kettner
- Gitarrenverstärker Dimavery
- Gitarrenverstärker AMT
- Gitarrenverstärker Budda
- Gitarrenverstärker Empress Effects
- Gitarrenverstärker DACS Audio
- Gitarrenverstärker Rivera
- Gitarrenverstärker DV Mark
Neueste Bedienungsanleitung für -Kategorien-
23 September 2024
19 September 2024
16 September 2024
6 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024