Extech SDL500 Bedienungsanleitung
Extech
Multimeter
SDL500
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extech SDL500 (12 Seiten) in der Kategorie Multimeter. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
User Manual
Hygro-Thermometer / Datalogger
Model SDL500
Additional ManualUser Translationsavailable at www.extech.com
2 SDL500-en-GB_1.4 11/16
Introduction
Congratulations on your purchase of the Extech SDL500 Hygro-Thermometer, an SD Logger Series
meter. This meter displays and stores Temperature and Relative Humidity readings from the
supplied probe and Temperature readings from an optional Type J or K Thermocouple probe. WET
BULB and DEW POINT temperature calculations can also be displayed. Logged data readings are
stored on an SD card for transfer to a PC. This meter is shipped fully tested and calibrated and, with
proper use, will provide years of reliable service.
Meter Description
1. Optional Thermocouple Input jack
2. Supplied Relative Humidity / Temperature Probe input jack
3. LCD Display
4. Power ON-OFF key
5. HOLD and Backlight key
6. MAX-MIN key
7. Up arrow â–² key
8. SET and Clock key
9. Down arrow â–¼ / FUNCTION key
10. ENTER and LOG key
11. PC interface jack
12. Reset Button
13. Power Adaptor jack
14. SD card slot
15. Temperature and Humidity sensors
Notes: Items 11 – 13 are located behind the snap-off compartment cover on meter’s right side.
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument
3 SDL500-en-GB_1.4 11/16
Getting Started
Power ON-OFF
ï‚· Power the meter by pressing and holding the power button for at least 1.5 seconds.
ï‚· Press and hold the power button for at least 1.5 seconds to power OFF the meter.
 This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor. If the meter
will not switch ON please check that fresh batteries are installed in the rear battery compartment
or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and
to an AC source.
Connecting the Supplied Relative Humidity/Temperature Probe
The supplied RH/Temperature Probe uses a keyed DIN-style plug to connect to the meter.
 Connect the supplied probe to the top right of the meter in the DIN jack labeled ‘Probe Input’.
 Press and hold the FUNCTION button until the ‘RH’ display icon appears. Release the button
when this ‘RH’ display icon appears. The RH reading in % are now on the upper, larger LCD
digits and Temperature in degrees ‘C’ or ‘F’ are now on the lower, smaller LCD digits.
ï‚· Use the Setup Mode to further configure the meter.
Connecting an optional Thermocouple Sensor
The SDL500 accepts an optional Type ‘J’ or Type ‘K’ Thermocouple Temperature sensor.
1. Connect a thermocouple to the sub-miniature jack at the top left of the meter labeled
‘Thermocouple Temp. Probe’.
2. Press and hold the FUNCTION button until the ‘TP’ display icon appears. Release the button
when this ‘TP’ display icon appears. The thermocouple reading in degrees ‘C’ or ‘F’ is now on
the LCD. The thermocouple type (‘J’ or K’) and the unit of measure are also displayed.
3. Use the Setup Mode to further configure the meter.
IMPORTANT SAFETY NOTE: The SDL500 can measure and display temperature up to 1300
o
C
(2372
o
F), however, thermocouple ratings vary widely; ensure that the thermocouple being used
is rated accordingly for the temperature being measured.
If an attempt is made to measure temperatures higher than the thermocouple’s rating, damage
to the thermocouple and the meter can result. If measurements are made outside the range of a
thermocouple personal injury is also possible.
Produktspezifikationen
| Marke: | Extech |
| Kategorie: | Multimeter |
| Modell: | SDL500 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extech SDL500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Multimeter Extech
19 September 2024
30 August 2024
28 August 2024
28 August 2024
28 August 2024
23 August 2024
18 August 2024
14 August 2024
14 August 2024
13 August 2024
Bedienungsanleitung Multimeter
- Multimeter Basetech
- Multimeter Gembird
- Multimeter Brennenstuhl
- Multimeter Clas Ohlson
- Multimeter Profile
- Multimeter REV
- Multimeter Voltcraft
- Multimeter Bosch
- Multimeter Laserliner
- Multimeter Velleman
- Multimeter Powerfix
- Multimeter Alecto
- Multimeter EMOS
- Multimeter TFA
- Multimeter FERM
- Multimeter Topcraft
- Multimeter Schneider
- Multimeter Tacklife
- Multimeter Abus
- Multimeter Elro
- Multimeter Stanley
- Multimeter Perel
- Multimeter Wago
- Multimeter Workzone
- Multimeter Somogyi
- Multimeter Amprobe
- Multimeter Metrix
- Multimeter Maxwell
- Multimeter Silverline
- Multimeter Yato
- Multimeter Brandson
- Multimeter Keithley
- Multimeter Hager
- Multimeter Kyoritsu
- Multimeter GW Instek
- Multimeter Monacor
- Multimeter Brüder Mannesmann
- Multimeter Milwaukee
- Multimeter JUNG
- Multimeter Testo
- Multimeter Elma
- Multimeter IDEAL
- Multimeter Digitus
- Multimeter Kingcraft
- Multimeter Testboy
- Multimeter Projecta
- Multimeter Greenlee
- Multimeter Multimetrix
- Multimeter BENNING
- Multimeter Metrel
- Multimeter Högert
- Multimeter APPA
- Multimeter Fluke
- Multimeter FLIR
- Multimeter Aldi
- Multimeter Gossen Metrawatt
- Multimeter Hubinont
- Multimeter Joy-it
- Multimeter Kewtech
- Multimeter Mastech
- Multimeter Megger
- Multimeter Micronta
- Multimeter PCE Instruments
- Multimeter Plieger
- Multimeter Sanwa
- Multimeter Skandia
- Multimeter Sonel
- Multimeter Steren
- Multimeter Uni-T
- Multimeter Wiha
- Multimeter Vimar
- Multimeter Owon
- Multimeter PeakTech
- Multimeter Amiko
- Multimeter Rigol
- Multimeter HT Instruments
- Multimeter Beha-Amprobe
- Multimeter Chauvin Arnoux
- Multimeter Aim TTi
- Multimeter Etekcity
- Multimeter Rohde & Schwarz
- Multimeter Strex
- Multimeter MBS
- Multimeter Kurth Electronic
- Multimeter Weidmüller
- Multimeter CEM
- Multimeter Klein Tools
- Multimeter Dasqua
- Multimeter Horex
- Multimeter Enovalab
- Multimeter Qian
- Multimeter Digi-tool
- Multimeter MGL Avionics
- Multimeter Cosinus
- Multimeter Weltron
- Multimeter EEVBlog
- Multimeter Caltek
- Multimeter Elworks
- Multimeter Bearware
- Multimeter Noyafa
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
13 Oktober 2024
9 Oktober 2024
5 Oktober 2024
5 Oktober 2024
3 Oktober 2024