EverFocus EZN368M Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für EverFocus EZN368M (87 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/87
Value IP Series Outdoor Network Camera
2-Megapixel 288 Series / 3-Megapixel 368 Series
Users Manual
EBN288/368
EZN288/368 EZN288/368M
EDN288/368M
Copyright © EverFocus Electronics Corp.
Release Date March, 2017 :
Copyright 1995-2017 EverFocus Electronics Corp.
Disclaimer
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Informaon
contained in this document is subject to change without notice.
Copyright
All rights reserved. No part of the contents of this manual may be reproduced or transmied in
any form or by any means without wrien permission of the EverFocus Electronics
Corporaon.
EverFocus
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
March, 2017
i
About this document
All the safety and operang instrucons should be read and followed before the unit is operated. This
manual should be retained for future reference. The informaon in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specicaons are
therefore subject to change without noce.
Regulatory Notices
FCC Noce "Declaraon of Conformity Informaon"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residenal installaon. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However, there is no guarantee that
interference will not occur in a parcular installaon. If this equipment does cause harmful interference
to radio or television recepon, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modicaons made to this equipment, not expressly approved by EverFocus or
pares authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operaon.
EverFocus Electronics Corp.
12F-1, No. 79, Sec. 1, Shin-Tai Wu Rd.,
Hsi-Chi, New Taipei City, Taiwan
Value IP Series camera complies with CE and FCC.
ii
Precauons
Do not install the camera near electric or magnec elds.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio
speakers since the electromagnec elds generated from these devices may distort the video image or
otherwise interfere with camera operaon.
Never disassemble the camera beyond the recommendaons in this manual nor introduce materials
other than those recommended herein.
Improper disassembly or introducon of corrosive materials may result in equipment failure or other
damage.
Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits, as well as creang unbalanced illuminaon beyond the capability of the camera to compensate.
1. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result in
electric shock.
2. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, re.
3. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the
hands. Use lens ssue or a coon pped applicator and ethanol to clean the sensor and the camera
lens. Use a damp so cloth to remove any dirt from the camera body. Please do not use complex
solvents, corrosive or abrasive agents for cleaning of any part of the camera.
4. Do not operate the camera beyond the specied temperature, humidity or power source rangs.
Use the camera at temperatures within -10°C ~ 5C / 14°F ~ 122°F, and humidity between 0% and
90%; this device is not rated as submersible. The input power source is 12VDC / PoE. Be sure to
connect the proper + / - polarity and voltage, as incorrect polarity or too high a voltage will likely
cause the camera to fail, and such damage is not covered by the warranty. The use of properly fused
or Class 3 power limited type supplies is highly recommended.
5. Mounng
Use care in selecng a solid mounng surface which will support the weight of the camera plus any
wind, snow, ice or other loading, and securely attach the camera to the mounng surface using
screws and anchors which will properly support the camera. If necessary (e.g. when mounng to
drop ceilings) use a safety wire to provide addional support for the camera.
Value IP 2MP 288 Series / 3MP 368 Series
4
2.1. Dimensions
EBN 288/368
EDN288/368M
EZN288/ 368
EZN288/ 368M
Value IP 2MP 288 Series / 3MP 368 Series
5
3. Features
SONY Progressive Scan CMOS sensor
Astounding image quality from the 3.6mm lens ( / EBN288 EBN 368 / EZN288 EZN368 / )
Motorized 2.8-12mm lens to capture the desired field of view ( EDN288M / EDN368M EZN 8M / 28
/ ) EZN368M
True Wide Dynamic Range Function (120dB)
Provides True Day/Night functionality with automatic IR filter operation
Extended IR range up to 30m / 100ft. with LEDs (Depending on scene IR reflectivity) IR
Multi-streaming from H.265 / H.264
1080p full real time recording
Weather proof IP66-rated
The flexible angle viewing with its 3-Axis rotation design allows wall or ceiling mounting
Supports Motion Detection & Email Notification
Supports live monitoring of video from mobile devices via MobileFocus / MobileFocus plus Apps
(iOS & Android)
Supports Power over Ethernet / 12VDC
Low light
Two-way audio*
Supports Alarm I/O*
Supports RS-485 (reserved)*
EverFocus Genie XMS CMS
ONVIF profile S compliant
Supports Micro SD card ( EDN288M / EDN368M / / EZN288 EZN368 / EZN288M ) / EZN368M
* Economic models not include the feature do
Value IP 2MP 288 Series / 3MP 368 Series
6
4. Installation
4.1. Packing List
Please check that there is no missing item in the package before installing.
No.
Item Name
EBN 288/368
EDN288/368M
EZN288/368
EZN288/368M
1
Camera
x 1
x 1
x 1
x 1
2
MAC Address Sticker
x 2
x 2
x 2
x 2
3
Screw Anchor
(in conjunction with
Screw)
x 4
x 3
x 3
x 4
4
Screw
x 4
x 3
x 3
x 4
5
Hexagon Wrench
(for adjusting the camera
position)
x 1
-
x 1
x 1
6
Cable Gland Kit
(connect to the LAN/PoE
cable for waterproofing)
x 1
x 1
x 1
x 1
7
Set Screw
x 3
-
-
-
8
Power Pigtail Cable
x 1
x 1
x 1
x 1
9
Accessories Instruction
(for installation of Set
Screw)
x 1
-
-
-
10
Software CD
x 1
x 1
x 1
x 1
11
Quick Installation Guide
x 1
x 1
x 1
x 1
12
Sticker
(Mounting Template)
x 1
x 1
x 1
x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for
possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
Value IP 2MP 288 Series / 3MP 368 Series
7
4.2. Optional Accessory
You can use the optional accessories to expand the capabilities and versatility of the camera. Please
contact your dealer for more information.
Junction Box
PBOX-A32
Junction Box (For ) EBN288/368
Apple White
119.2 x 38mm / 4.7" x 1.5" (D) x (H)
High-strength Aluminum for better protection against damage.
Spray painted surface to protect the bracket from corrosion and rust.
PBOX-A32-1
Junction Box (For / ) EZN288 / / EZN368 EZN288M EZN368M
Apple White
119.2 x 38mm / 4.7" x 1.5" (D) x (H)
High-strength Aluminum for better protection against damage.
Spray painted surface to protect the bracket from corrosion and rust.
PBOX-A32-2
Junction Box (For ) EDN288M / EDN368M
Apple White
119.2 x 38mm / 4.7" x 1.5" (D) x (H)
High-strength Aluminum for better protection against damage.
Spray painted surface to protect the bracket from corrosion and rust.
IP Sidekick
IP Sidekick - ESK1000
Using it for installation, you do not need to pre-configure the IP
address or to use an additional monitor to check and adjust all the IP
cameras. The product can assign an IP address to the camera, then you
can connect and check the camera live view using EverFocus mobile
App EF Sidekick. For details about IP Sidekick, please refer to the IP
Sidekick ESK1000 Us ers Manual.
PoE Switch
EverFocus 5 / 8 / 16 / 24
Ports PoE Switch
5 Ports: ES0501- 40
8 Ports: ES0812-31 / ES0802- 41
16 Ports: ES1625-31 / ES1645-51
24 Ports: ES2426-31 / ES2446-51 / ES2448- 62
Value IP 2MP 288 Series / 3MP 368 Series
8
4.3. Cables
The Cables provide connections for Network, BNC output, power, audio input / output, RS-485 (reserved)
and alarm inputs / output. A Reset Button is also provided. Note that the audio-in / out cable features a
line 3.5mm jack (TRS). Be sure to prepare microphones / speakers with TRS connector (see TRS
Connector image below). Also, microphones / speakers with a (built-in) amplifier and external power
supply are required.
12VDC Input
LAN / PoE Cable
Audio Input (TRS Line-in)
(Red)
Audio Output (TRS Line-out)
(White)
Alarm Input (Black)
Reset Button
Alarm Output /
RS-485 (Red)
Video Output
Cable
EBN 288/368
EDN288/368M
EZN288/368
EZN288/368M
Alarm In 2 x
Yes (with a
terminal block)
Yes (with a
terminal block)
Yes (with a
terminal block)
Yes (with a
terminal block)
Alarm Out /
RS- 485
(reserved)
Yes (with a
terminal block)
Yes (with a
terminal block)
Yes (with a
terminal block)
Yes (with a
terminal block)
Audio In
Yes (Red)
Yes (Red)
Yes (Red)
Yes (Red)
Audio Out
Yes (White)
Yes (White)
Yes (White)
Yes (White)
BNC
Yes
Yes
Yes
Yes
RJ45
Yes
Yes
Yes
Yes
12VDC
Yes
Yes
Yes
Yes
Reset Button
Yes (with a
dust-proof cap)
-
-
Yes (with a
dust-proof cap)
Value IP 2MP 288 Series / 3MP 368 Series
9
For Economic models, the cables provide connections for Network, power and Reset Button.
12VDC Input
LAN / PoE Cable
Reset Button
Economic Models Cables
Cable
EBN288/368
EDN288/368M
RJ45
Yes
Yes
12VDC
Yes
Yes
Reset
Button
Yes (with a
dust-proof
cap)
-
Cable
EZN288/368
EZN288/368M
RJ45
Yes
Yes
12VDC
Yes
Yes
Reset
Button
-
Yes (with a
dust-proof cap)
Audio Function
TRS Connector
Left Channel (Tip)
Right Channel (Ring)
Ground (Sleeve)
To activate the Audio function, the Complex Stream must be selected.
See in Stream 7.2.1 Streaming Settings.2 .
Pin Assignment
Alarm Output / RS-485 (reserved)
Alarm Output
COM (-)
NO (+)
RS- 485
(reserved)
B (+)
A (-)
Alarm Input
Alarm In 1
GND (-)
Alarm In (+)
Alarm In 2
Alarm In (+)
GND (-)
Value IP 2MP 288 Series / 3MP 368 Series
10
Reset Button
1. Reboot the camera:
When the camera is powered up, press the Reset Button will reboot the camera.
2. Restore the camera:
Keep the pressed, at the same time unplug the camera power then plug it back again Reset Button
will return camera settings to the factory default values.
4.4. Basic Installation
4.4.1. Mounting and Wiring
EBN 288/368
1. Before screwing the camera to the wall, stick the Sticker on the wall / ceiling to mark the position
for installation. Drill four holes on the wall / ceiling according to the supplied Sticker and push the
supplied four into the four holes on the wall / ceiling. Drill another hole in the Screw Anchors
middle of the Sticker if you wish to run the wires into the wall / ceiling.
2. Twist the Outer Housing counterclockwise and then remove the Outer Housing from the camera
base.
3. Place the camera base on the wall / ceiling and run the cable through the camera base first.
Value IP 2MP 288 Series / 3MP 368 Series
11
4. Tread the cables:
a. From the side cut of the camera base
b. Through the wall / ceiling: run the cables through the hole on the wall / ceiling.
Wall or
Ceiling
5. Use the supplied four to screw the camera base to the ceiling / wall. Screws
6. Adjust the camera angle and twist back the Outer Housing simultaneously.
7. Optionally screw back the by using the supplied to prevent Set Screw Hexagon Wrench
uninstallation.
Value IP 2MP 288 Series / 3MP 368 Series
12
8. Connect the LAN / PoE cable to the camera.
a. Remove the Screw Cap Cable Gland from the .
b. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through the Cable
Gland Screw Cap and .
c. Place the Waterproof Ring into the LAN / PoE cable. Connect the RJ-45 cable to the RJ-45
Connector Cable. Tightly screw the and to the RJ-45 Connector Cable. Cable Gland Screw Cap
9. Optionally connect the camera to the 12VDC power source using the supplied Power Adapter
Pigtail or a power adapter.
Power Adapter Pigtail
Power Cable
RJ-45 Connector
or
Power Adapter
Value IP 2MP 288 Series / 3MP 368 Series
13
EDN M 288/368
1. Before screwing the camera to the wall, stick the Sticker on the wall / ceiling to mark the position
for installation. According to the supplied Sticker, drill three screw-depth holes on the wall / ceiling,
and then drill a through-wall hole for wiring the camera cables. Push the supplied three rew Sc
Anchors into the four holes on the wall / ceiling.
Wall or Ceiling
Sticker
Anchors
Screws
2. Unscrew the camera cover and screw the camera base to the ceiling / wall by using the supplied
Screws.
3. Optionally insert the micro SDHC / SDXC ca Please refer to . rd. 4.4.2 Inserting a micro SD Card
4. Connect the LAN / PoE cable to the camera.
a. Remove the Screw Cap Cable Gland from the .
Value IP 2MP 288 Series / 3MP 368 Series
14
b. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through the Cable
Gland rew Cap and Sc .
c. Place the Waterproof Ring into the LAN / PoE cable. Connect the RJ-45 cable to the RJ-45
Connector Cable. Tightly screw the and to the RJ-45 Connector Cable. Cable Gland Screw Cap
5. Optionally connect the camera to the 12VDC power source using the supplied Power Adapter
Pigtail or a power adapter.
Power Adapter Pigtail
Power Cable
RJ-45 Connector
or
Power Adapter
6. Access the camera live view. See 5 Accessing the Camera. . Or using a video Test-Out cable to
connect a monitor to the camera for setting image aim and focus.
7. To adjust camera angles.
Pan Adjustment: Simply turn left / right of the 3-Axis bracket by 75° to the desired position.
75° 75°
3-Axis
Bracket
Value IP 2MP 288 Series / 3MP 368 Series
15
Rotational Adjustment: Loosen the rotate screw and rotate the camera left / right to the desired
position, then tight the rotate screw. Due to the internal connector design, it is recommended en
not to rotate the camera more than 30°.
30°
30°
Rotation screw
Tilt Adjustment: Loosen the two tilt screws and adjust the angle by ° to the desired position, then 75
tighten the tilt screw.
75°
Tilt screw
8. Secure the cover back to the camera.
EZN288/ EZN288/ M 368 & 368
1. Before screwing the camera to the wall, stick the Sticker on the wall / ceiling to mark the position
for installation. Drill three ( ) four ( ) holes on the wall / ceiling EZN288/368 or EZN288/ M368
according to the supplied and push the supplied into the three holes on the wall / Sticker Anchors
ceiling. Drill another hole in the middle of the Sticker if you wish to run the wires into the wall /
ceili . ng
EZN288/368
EZN288/ M368
Value IP 2MP 288 Series / 3MP 368 Series
16
2. You can wire the cables from the side of the camera or through the wall.
Wire the cables from the side of the camera Wire the cables through the wall
3. Place the camera’s base against the anchoring surface so that the holes line up. Screw the camera
to the wall / ceiling using the supplied . Screws
4. Optionally insert a micro SD / SDHC card into the card slot. Please refer to 4.4.2 Inserting a micro SD
Card.
5. Connect the LAN / PoE cable to the camera.
a. Remove the Screw Cap Cable Gland from the .
b. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through the Cable
Gland Screw Cap and .
c. Place the Waterproof Ring into the LAN / PoE cable. Connect the RJ-45 cable to the RJ-45
Connector Cable. Tightly screw the and to the RJ-45 Connector Cable. Cable Gland Screw Cap
Value IP 2MP 288 Series / 3MP 368 Series
17
6. Optionally connect the camera to the 12VDC power source using the supplied Power Adapter
Pigtail or a power adapter.
Power Adapter Pigtail
Power Cable
RJ-45 Connector
or
Power Adapter
7. Access the camera live view. See 5 Accessing the Camera. . Or connect a handheld test monitor to
the CVBS wire on the Cable Assembly for adjusting viewing angles.
8. To adjust the camera angles:
Pan Adjustment: Loosen the Set Screw using the supplied Hexagon Wrench. Rotate the camera by
360° to the desired position and screw the Set Screw until it locks against the Camera Base.
Set Screw
Camera
Base
360°
Set Screw
Camera Base
360°
EZN EZN288/368 288/368M
Value IP 2MP 288 Series / 3MP 368 Series
21
5. Put the water-proof ring on the groove that near the edge of the housing. Place the desiccant
bag beside the IPC board.
Water-proof ring
Desiccant bag
6. Screw back the IPC board, secure the rear housing back to the front housing and tighten the set
screws on the bracket.
Note: Please make sure you wear the antistatic gloves or antistatic wrist strap when installing the
Micro SD card to protect the device from damage.
Value IP 2MP 288 Series / 3MP 368 Series
22
5. Accessing the Camera
This section explains how to access the Web interface of the camera for configuration.
5.1. Checking the Dynamic IP Address
You can look up the IP address and access the Web interface of the IP camera using the IP Utility (IPU)
program, which is included in the software CD. The IP Utility can also be downloaded from EverFocus’
Website: http://www.everfocus.com.tw/HQ/Support/DownloadCenter_p1.aspx (Support > Download
Center > Keyword Search: IP Utility). Please connect the IP camera on the same LAN of your computer.
1. Save IP Utility Setup .exe in your computer. Double click the .exe file and follow the
on‐screen instructions to install the IP Utility.
2. To access the Live View window, double click the IP address of the desired device, the login window
pops up. Type the user ID and password to log in. By default, the user ID is and the password user1
is . 11111111
Value IP 2MP 288 Series / 3MP 368 Series
24
5.2. Settings for Microsoft Internet Explorer
If you have difficulties viewing live view or upgrading firmware, it is suggested to complete the following
settings of your computer.
1. If your PC or laptop is running with Windows, it s required to run the browser as administrator
when first entering the remote web page of the device. Go to C:\Program Files (x86)\Internet
Explorer, right-click the browser and then click Run as administrator.
2. You may need to turn User Account Control off if you still can t see the Remote Live View. On the
computer, click Start > Control Panel > System and Security > Action Center (click Change User
Account Control Settings), the User Account Control Settings window appears. Adjust the slide bar
to Never Notify and then click OK. Restart your computer if requested.
Value IP 2MP 288 Series / 3MP 368 Series
25
5.3. Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection Direct ,
High-Speed Connection One- -One Connection and to .
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows multiple
users on and off site to see the IP camera on a LAN / WAN (Internet). The camera must be assigned an IP
address that is compatible with its LAN. By setting up port forwarding on the router, you can remotely
access the cameras from outside of the LAN via the Internet. To remotely access the Web interface of
the IP camera, please refer to 7.1.1 Network (DDNS Settings). To set up port forwarding, please refer to
Appendix D. Setting up Port Forwarding Function.
High-speed modem
Internet
Straight-through LAN patch cable
Router
Cat 5 Straight Through Cable
Left: Pinout of a straight-through cable.
Value IP 2MP 288 Series / 3MP 368 Series
28
7. Event signal icons
When an event is triggered, the alarm icon at the top of the Live View window will turn red
and blink to alert the user. Click the icon to view the alarm information. On the p-up windowpo ,
click to stop / start prompting alarm information, click to remove Disarming / Arming Clear Alarm
the current alarm information from the list.
8. Snapshot
Click the button to take a snapshot, and the storage folder will pop up automatically. By Snapshot
default, the snapshot will be saved at C:Everfocus/Value_3M/Snapshots. To change the location, see
Live View Snapshot in 7.1.9 Local Settings.
9. Record
Click the Record button to start / stop recording the current video stream. By default, the recordings
will be saved at C:Everfocus/Value_3M/Recordings. To change the location, see Live View Recording
in 7.1. 9 Local Settings.
10. Two-way Audio
Click the Two-way Audio buttons to switch the sound on / off for the speakers and microphones (if
such external devices have been connected to the camera directly or via the network To activate ).
the Audio function, the Complex Stream must be selected. See in 7.2.1 StreamStream .2 Settings.
Note that the camera provides the TRS line-in / out terminal I/O, therefore, TRS microphones /
speakers with a (built-in) amplifier and external power supply are required.
11. Full Screen
Click to display the current camera stream in full screen. To exit full screen, right-click the mouse or
press the button on keyboard. Under full screen mode, these icons help you quickly be alerted ESC
of motion events, turn the audio on/off and take snapshots.
When a motion event is triggered, the alarm icon will turn red to alert the user.
Click the buttons to switch the sound on / off for the speakers (if such external devices Audio
have been connected to the camera directly or via the network ).
Click the button to take a snapshot. Snapshot
Value IP 2MP 288 Series / 3MP 368 Series
31
Note:
1. By default, the system will automatically adjust the IR LED strength according to the scene, so please
avoid IR reflection when installing the camera to prevent out- -focus at night. of
2. Under focus mode, if the camera does not focus after switching the Day/Night mode, it is Auto
recommended to switch the focus mode to and adjust focus manually. Manual
6.4 Account
Click the button to display the account panel.
Account: Display the current user's login account.
Logout: ick to log out of the Web interface. Cl
7. System
Click the System tab on the Live View Window to enter the setting page Click the item of the one you want .
to see in the setting menu to display the details.


Produktspezifikationen

Marke: EverFocus
Kategorie: Überwachungskamera
Modell: EZN368M

Brauchst du Hilfe?

Wenn Sie Hilfe mit EverFocus EZN368M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Überwachungskamera EverFocus

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-