Epson PowerLite 6100 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Epson PowerLite 6100 (80 Seiten) in der Kategorie Beamer. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/80
PowerLite® Home Cinema 6100/6500 UB
Home Theater Projector
User’s Guide
2
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Trademarks
Epson is a registered trademark, 1080Perfect is a trademark, and Epson Exceed Your Vision is a registered
logomark of Seiko Epson Corporation.
PowerLite and PrivateLine are registered trademarks, DigiScan and AccuCinema are trademarks, and Extra Care
and Epson Connection are service marks of Epson America, Inc.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
x.v.Color is a trademark of Sony Corporation.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2008 Epson America, Inc. 11/08
CPD-26527R1
Contents 3
Contents
Introduction 7
Projector Parts 8
Front 8
Back 8
Bottom 9
Projector Control Panel 9
Remote Control Button Map 10
Optional Accessories 11
Registration and Warranty 11
Using This Manual 12
Setting Up the Projector 13
Choosing a Location 13
Installing the Projector 17
Connecting the Cables 19
Connecting Video and Computer Equipment 19
Making Other Connections 21
Installing Batteries in the Remote Control 22
Turning the Projector On and Off 22
Turning On the Projector 22
Turning Off the Projector 23
Selecting the Image Source 24
Positioning the Image 25
Making Basic Adjustments 27
Focusing and Zooming 27
Choosing the Aspect Ratio 28
Choosing the Color Mode 29
4Contents
Advanced Color Adjustments 30
Adjusting the Gamma Setting 30
Adjusting RGBCMY 31
Locking the Projector 32
Making Detailed Adjustments 33
Using the Menu System 33
Changing How the Menus Display 35
Adjusting the Picture Quality 35
Input Brightness Settings 35
Sharpness and Picture Quality Settings 37
Color Settings 40
Adjustments for Computer Images 42
Selecting Memory Settings and Resetting the Projector 43
Selecting Memory Settings 43
Creating Memory Settings 43
Renaming Memory Settings 44
Deleting Saved Memory Settings 44
Resetting the Projector 45
Customizing Projector Features 46
Image Sizing 46
Screen Options 47
Other Setup Options 47
Maintenance 49
Cleaning the Lens 49
Cleaning the Projector Case 50
Cleaning and Replacing the Air Filter 50
Replacing the Lamp 52
Resetting the Lamp Usage Timer 55
Checking the Projector Status 55
Storing the Projector 56
Transporting the Projector 56
Contents 5
Problem Solving 57
What To Do When the Lights Come On or Flash 57
Solving Picture Problems 59
Solving Remote Control Problems 62
Where To Get Help 63
Specifications 65
General 65
Lamp 66
Remote Control 66
Dimensions 66
Electrical 66
Environmental 67
Safety 67
Compatible Video Formats 68
ESC/VP21 Command Codes 70
Notices 71
Important Safety Information 71
FCC Compliance Statement 73
Declaration of Conformity 74
Epson America, Inc. Limited Warranty 75
Index 77
6Contents
Introduction 7
Introduction
The PowerLite® Home Cinema 6100/6500 UB projector lets you enjoy theater-quality
images in the relaxing environment of your own home. Designed especially for home cinema
use, it offers these outstanding features:
■Native 1080p (1920 × 1080) resolution, dynamic contrast ratio up to 75000:1 (18000:1
for the Home Cinema 6100), and up to 1600 lumens (Home Cinema 6500 UB) or
1800 lumens (Home Cinema 6100) of brightness (white light output and color light
output) for incredibly rich, sharp images in any room lighting
■Auto Iris system that constantly controls the lamp intensity based on the gamma and
black/white levels of your projected content, for perfectly adjusted images and deepest
blacks
■Epson® Crystal Fine 3LCD technology for reliable picture quality, increased contrast
ratio and uniform colors
■1080Perfect™ video processing using HQV
® Reon-VX technology for more film-like
images free of noise or artifacts
■10-bit color quality for unmatched color accuracy, with over a billion colors available
■Epson AccuCinema™ color management delivered by the built-in optical Cinema Filter
blocks out excess light for an expanded, purer color range and sophisticated grayscale
tracking
■HDMI™
(High Definition Multimedia Interface
™) port for superior, uncompressed
digital video
■True 16:9 wide-format projection
■Flexible setup configurations, including front projection and ceiling mounted, with
vertical and horizontal offset lens shift
■Seven color modes, including x.v.Color
™, to quickly optimize viewing for different
lighting environments, and a vast array of custom color adjustments
8Introduction
Projector Parts
Control panel (top)
Ventilation slots
Lens cover
Vertical lens shift dial
Adjustable foot
Video port
HDMI ports
Component
video port
AC power inlet
Infrared receiver
Kensington®
lock port
Infrared receiver
Horizontal lens shift dial
S-Video port
Control (RS-232C) port
Trigger out
port
PC port
Zoom ring
Focus ring
Main power switch
Front
Back
Lamp cover
Control panel
(side)
Air intake (filter)
Lamp cover release
Cable holder
Introduction 9
Power
button
Menu navigation
button
Esc button
Exits the current
menu item
Menu button
Displays the
menus
Warning lights
Mounting bracket
attachment points
Enter button
Selects menu items or
opens the line menu
Bottom
Projector Control Panel
Optional cable cover
attachment points
(brass colored)
Top control panel Side control panel
Source button
Switches the
video input source
10 Introduction
Remote Control Button Map
Source buttons
Switch between equipment
connected to the projector
Color Mode button
Optimizes viewing for
different lighting environments
Power button
Turns projector on or off
Memory button
Recalls custom
picture settings
Menu navigation
buttons
Pattern button
Displays test patterns
to adjust the image
Menu button
Displays the projector’s menus
Aspect button
Changes the picture’s aspect ratio
Esc (escape) button
Exits the current menu item
Blank button
Temporarily stops projection or
hides the menu screen
Enter/Line Menu button
Selects menu items or opens
the line menu
Gamma button
Adjusts the gamma values
of the screen display
Default button
Restores default settings
when menu is displayed
Sharpness button
Adjusts image sharpness
Illumination button
Lights the remote control
buttons for easy viewing
RGBCMY button
Adjusts the hue,
saturation, and brightness
for each color
Introduction 11
Optional Accessories
Epson provides the following optional accessories for the projector:
You can purchase accessories from an authorized Epson reseller. To find the nearest
reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Registration and Warranty
Your projector comes with a basic two-year carry-in warranty. For details, see page 75.
In addition, Epson offers free Extra Care
SM Home Service. In the unlikely event of an
equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will
ship you a replacement unit anywhere in the United States or Canada, usually via overnight
delivery. See your Extra Care Home Service brochure for details.
To register, simply fill out the registration card that came with your projector and mail it to
Epson. Or you can register online at . Registering also lets you www.epson.com/webreg
receive special updates on new accessories, products, and service.
Product Part number
Replacement lamp V13H010L49 (ELPLP49)
Air filter replacement V13H134A21 (ELPAF21)
Kensington security lock (anti-theft device) ELPSL01
Cable cover V12H003002 (ELPCC01W)
Projector mount ELPHB800
12 Introduction
Using This Manual
This book contains all the information you need to use the projector, in addition to basic
setup and maintenance instructions, troubleshooting tips, important safety instructions,
specifications, and warranty information.
Please follow these guidelines as you read through the manual:
Warning: Must be followed carefully to avoid bodily injury.
Caution: Must be observed to avoid damage to your equipment.
Note: Contains important information about your projector.
Tip: Contains helpful projection tips.
Need additional help? Take advantage of Epson’s automated support services 24 hours a day
at www.epson.com/support. Use this site to view FAQs (Frequently Asked Questions) or
product information and e-mail your questions to Epson support.
If you need more help, you can use the Epson PrivateLine
® Support service. Call
(800) 637-7661 and enter the PIN on the PrivateLine support card that came with your
projector.
Setting Up the Projector 13
Setting Up the Projector
Follow the instructions in this section to choose a location for the projector, connect the
cables, and display an image.
Choosing a Location
You can install the projector for the viewing setups shown below, as well as rear projection.
Center
Ceiling
Side
14 Setting Up the Projector
Ideally, keep the projector level and place it at a height so its lens is centered between the top
and bottom of the screen, as shown below. If this is not possible, you can use the lens shift
dials to reposition the image. As a rule of thumb, you can use lens shift to move the image up
or down by nearly its full height, and left or right by about one-half its width (for details, see
page 26).
If you place the projector off to the side, aim it straight ahead (rather than at the center of the
screen), then use the horizontal lens shift dial to center the image on the screen.
Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the
lens shift dials to change the lens position.
Projection distance
Offset A
Offset B
Offset refers to distance from
bottom of image to center of
lens using maximum lens shift.
Vertical lens shift dial
Horizontal lens shift dial
Setting Up the Projector 15
The size of the image is determined by the distance from the projector’s lens to the screen.
Depending on your display settings and how you use the Zoom ring, the actual size may
differ. Use this table as a rough guide for projector placement:
* Offset B is about 10 percent less for the Home Cinema 6100.
16:9 aspect ratio
Projection distance
Diagonal image size
(width × height) Offset A Offset B*
Horizontal
Offset
2.8 to 6.2 feet
0.87 to 1.88 m
30 in. (26 × 15 in.)
76.2 cm (66 × 37 cm)
6.8 in.
17 cm
21.5 in.
55 cm
0 to 13 in.
0 to 33 cm
3.8 to 8.3 feet
1.17 to 2.52 m
40 in. (35 × 20 in.)
101.6 cm (89 × 50 cm)
9.1 in.
23 cm
28.7 in.
73 cm
0 to 17 in.
0 to 43 cm
5.8 to 12.5 feet
1.77 to 3.80 m
60 in. (51 × 28 in.)
152.4 cm (130 × 75 cm)
13.6 in.
35 cm
43.0 in.
109 cm
0 to 26 in.
0 to 66 cm
7.8 to 16.7 feet
2.38 to 5.0 m
80 in. (71 × 39 in.)
203.2 cm (180 × 100 cm)
18.2 in.
46 cm
57.4 in.
146 cm
0 to 35 in.
0 to 89 cm
9.8 to 20.9 feet
2.98 to 6.36 m
100 in. (87 × 47 in.)
254 cm (220 × 120 cm)
22.7 in.
58 cm
71.7 in.
182 cm
0 to 44 in.
0 to 112 cm
11.8 to 25.1 feet
3.59 to 7.64 m
120 in. (106 × 59 in.)
305 cm (270 × 150 cm)
27.0 in.
69 cm
86.0 in.
219 cm
0 to 52 in.
0 to 132 cm
14.7 to 31.4 feet
4.50 to 9.56 m
150 in. (130 × 75 in.)
381 cm (330 × 190 cm)
34.0 in.
86 cm
107.6 in.
273 cm
0 to 65 in.
0 to 165 cm
19.7 to 41.8 feet
6.01 to 12.76 m
200 in. (173 × 98 in.)
508 cm (440 × 249 cm)
45.4 in.
115 cm
143.5 in.
364 cm
0 to 87 in.
0 to 221 cm
4:3 aspect ratio
Projection distance
Diagonal image size
(width × height) Offset A Offset B*
Horizontal
Offset
3.5 to 7.6 feet
1.07 to 2.31 m
30 in. (24 × 18 in.)
76.2 cm (61 × 46 cm)
8.3 in.
21 cm
26.3 in.
67 cm
0 to 16 in.
0 to 41 cm
4.7 to 10.1 feet
1.44 to 3.09 m
40 in. (32 × 24 in.)
101.6 cm (81 × 61 cm)
11.1 in.
28 cm
35.1 in.
89 cm
0 to 21 in.
0 to 53 cm
7.1 to 15.3 feet
2.18 to 4.66 m
60 in. (47 × 35 in.)
152.4 cm (120 × 90 cm)
16.7 in.
42 cm
52.7 in.
134 cm
0 to 32 in.
0 to 81 cm
9.6 to 20.4 feet
2.92 to 6.23 m
80 in. (63 × 47 in.)
203.2 cm (160 × 120 cm)
22.2 in.
56 cm
70.2 in.
178 cm
0 to 43 in.
0 to 109 cm
12 to 25.5 feet
3.66 to 7.79 m
100 in. (79 × 59 in.)
254 cm (200 × 150 cm)
27.8 in.
71 cm
87.8 in.
223 cm
0 to 53 in.
0 to 135 cm
16 Setting Up the Projector
* Offset B is about 10 percent less for the Home Cinema 6100.
To determine the exact image size when you know the projection distance (or the exact
projection distance when you know the desired image size), you can use the Projection
Distance Calculator. You can download this program from the Epson website at
www.epson.com/support.
Also keep these considerations in mind:
■Make sure there is plenty of space for ventilation around and under the projector. Do not
set the projector on top of loose materials that could block the vents underneath.
■Make sure the projector is within 9.8 feet (3 m) of a grounded electrical outlet or
extension cord.
14.4 to 30.7 feet
4.40 to 9.36 m
120 in. (94 × 71 in.)
305 cm (240 × 180 cm)
33.0 in.
85 cm
105.0 in.
268 cm
0 to 64 in.
0 to 163 cm
18 to 38.4 feet
5.51 to 11.71 m
150 in. (118 × 91 in.)
381 cm (300 × 230 cm)
41.7 in.
106 cm
131.7 in.
334 cm
0 to 80 in.
0 to 203 cm
24.2 to 51.3 feet
7.36 to 15.62 m
200 in. (161 × 118 in.)
508 cm (410 × 300 cm)
55.6 in.
141 cm
175.6 in.
446 cm
0 to 107 in.
0 to 271 cm
4:3 aspect ratio
Projection distance
Diagonal image size
(width × height) Offset A Offset B*
Horizontal
Offset
Setting Up the Projector 17
Installing the Projector
To install the projector, you first need to determine the location, based on the size of your
screen (maximum diagonal image size). Use the table on page 15 as a guide to positioning the
projector.
To suspend the projector from a ceiling, you will need the optional projector mount designed
for the projector. See page 11 for ordering information. Follow the instructions included with
the mount to install the projector.
Warning: When installing or adjusting the ceiling mount, do not use adhesives to prevent the
screws from loosening and do not use any type of oil or lubricant. These may cause the projector
casing to crack and the projector may fall, causing serious injury and serious damage to the
projector.
If you install the projector on the ceiling, you will need to invert the picture so that it appears
right side up. Follow these steps:
1. Press the Menu button on the remote control.
2. Open the Settings menu, then select Projection.
3. Select Front/Ceiling.
4. Press the Menu button when done.
Note that you can rotate the Epson logo plate
180 degrees when suspending the projector from a
ceiling.
If you are planning to use an AV controller with the
projector, refer to the table of ESC/VP21 command
codes on page 70.
18 Setting Up the Projector
The following illustrations show the dimensions of the projector:
5.4 in.
136 mm
Center of lens
2.8 in.
72 mm
5.8 in.
148 mm
0.5 in.
12 mm
5.2 in.
131 mm
17.7 in.
450 mm
0.2 in.
4.5 mm
11.8 in.
300 mm
5.9 in.
150 mm
3.0 in.
75 mm
2.2 in.
56 mm
1.8 in.
45 mm
5.3 in.
135 mm
6.3 in.
160 mm
15.3 in.
390 mm
M4×9mm
Setting Up the Projector 19
Connecting the Cables
Connecting Video and Computer Equipment
You can connect the projector to many types of video equipment, such as a VCR, DVD
player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera.
You can also connect it to a desktop or laptop PC or Apple
® Macintosh® system. For details
on compatible video formats, see page 68.
You can connect up to six pieces of video equipment at the same time, using any of the
commercially available cables shown below:
Port name Video equipment connection Computer connection
HDMI 1/
HDMI 2
Use an HDMI cable:
Component Use a component video cable
(with RCA-style connectors):
Connect the cable to the three
component video ports. Match
corresponding colors between the
cable and the ports.
—
PC — Use a Mini D-sub, 15-pin monitor cable
to connect to a computer RGB
(monitor) port:
S-Video Use an S-video cable: —
Video Use an RCA video cable: —
20 Setting Up the Projector
For best results, connect your video equipment to the HDMI port, if possible. If your
equipment doesn’t support HDMI, connect it to one of the following ports (highest quality
listed first): Component (for component video), S-Video, or Video (for composite video).
When you connect a large or heavy cable to the projector,
such as an HDMI cable, it is recommended that you fasten
it to one of the two holders using a commercially available
cable tie.
Connect video equipment to one
of these ports
Connect a computer to one
of these ports
Setting Up the Projector 21
Making Other Connections
Connect the power cable and other cables described below, depending on how you plan to
use the projector.
■Plug the power cable into the projector and a grounded electrical outlet.
■The Trigger out port outputs a 12-volt DC signal
when the projector is turned on. This lets a central
control system monitor whether the projector is on
or off, and can be used to raise or lower your
projection screen automatically when the projector
is in use.
Connect a 3.5-mm mini jack to the port, as shown.
To enable the port, turn on the Trigger Out
setting (see page 48).
■To use an AV controller with the projector, connect a 9-pin null modem serial cable to
the RS-232C port. Refer to the table of ESC/VP21 command codes on page 70.
22 Setting Up the Projector
Installing Batteries in the Remote Control
The remote control uses two AA batteries.
Warning: Keep batteries away from children. If a battery is swallowed, contact your doctor
immediately.
1. Release the tab and lift open the cover.
2. Insert two new AA batteries as shown.
3. Insert the tab on the cover and press it down until it
clicks into place.
Aim the remote control at the screen, or at the front or
back of the projector. Make sure you are within 30 feet
of the projector.
If you suspect the batteries are weak, press the illumination button. If the buttons do not
glow, replace the batteries.
Turning the Projector On and Off
Turning On the Projector
1. Remove the lens cap.
2. Turn on any connected equipment you plan to use.
3. Turn on the main power switch on the back of the projector.
ON
Setting Up the Projector 23
4. Press the Ppower button on the remote control or projector.
Note: To prevent children from turning on the projector, you can use the Child Lock feature. See
page 32 for details.
If you’ll be using the projector at an altitude above 4900 feet (1500 meters), turn on High Altitude
Mode so the fan can properly cool the projector at the high altitude air pressure. See page 48 for
details.
The projector takes about 30 seconds to warm up and display an image. If you don’t see a
picture, you may need to change the image source as described on page 24.
Turning Off the Projector
1. Turn off any equipment connected to the projector.
2. Press the Ppower button on the remote control or projector. When you see a
confirmation message, press the Ppower button again to turn the projector off.
3. When the Ppower light stops flashing orange and stays on, turn off the projector’s main
power switch on the back.
It is now safe to unplug the projector, if necessary.
Caution: Turn off this product when not in use to prolong the life of the projector. Continuous
24-hour-a-day use may reduce the overall life of the product. Never turn off the main power switch
without first turning off the projector and letting it cool as described above, or you could damage it
and reduce lamp life.
Remote control Projector
24 Setting Up the Projector
Selecting the Image Source
The source buttons on the projector and remote control let you switch between images from
different pieces of equipment connected to the projector (such as a DVD player, cable or
satellite box, or video game console).
Press the Source button on the remote control that corresponds to the port to which your
video source is connected.
If you press the source button on the projector, you see a list of available sources. Press
the source button to move through the list and select the desired source.
Note: If an image does not appear, see “Problem Solving” on page 57.
To temporarily turn off the image and darken the screen, press the Blank button on the remote
control. Press the Blank button again to return to normal viewing.
Setting Up the Projector 25
Positioning the Image
If the image is not centered on the screen, use the horizontal and vertical lens shift dials to
adjust its position.
Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the
lens shift dials to change the lens position.
Note: You can display a test pattern to help adjust the image position by pressing the Pattern
button on the remote button to turn off the test pattern.control. Press the Esc
When you hear a click, the lens position is almost centered. If the lens shift dial becomes
difficult to turn, you cannot adjust the position any further.
If one side of the image is taller than the other, make sure the projector is parallel to the
screen. If necessary, adjust the front feet so that the projector is horizontal.
Vertical lens shift dial
Horizontal lens shift dial
Adjustable feet
26 Setting Up the Projector
The image cannot be moved to the maximum distance in both the vertical and horizontal
directions. For example, the image cannot be shifted vertically when it has been shifted
horizontally by the full amount. When the image has been shifted vertically by the full
amount, it can be shifted up to 9 percent of the width of the image. The amount by which
you can shift the image is expressed in terms of the image width (W) and height (H), as
shown below:
H
H
H
Move
upwards
Move to
the left
Move to
the right
Move
downwards
1/2H
1/2W
Maximum lens
shift boundary
(85% for the Home Cinema 6100)
Making Basic Adjustments 27
Making Basic Adjustments
Follow the instructions in this chapter to make basic adjustments to the image shape, size,
color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33.
Focusing and Zooming
Use the focus ring to sharpen the image.
Use the zoom ring to reduce or enlarge the image.
Focus ring
Zoom ring
28 Making Basic Adjustments
Choosing the Aspect Ratio
In many cases, video signals are automatically resized to fit
on your screen when Auto is selected as the Aspect setting.
You may need to change the size of the image (or aspect
ratio) for certain image types by pressing the Aspect button
on the remote control.
Select one of these settings:
■ Normal for standard TV broadcasts, computer images,
or images with a 4:3 aspect ratio.
■ Full for images recorded in squeeze mode.
■ Zoom for images recorded in 16:9 (wide-screen) format.
■ Wide for expanding a 4:3 image to 16:9 so it fills the whole screen. This stretches only
the right and left sides of the image; the central part is unchanged.
Note: When displaying 720p, 1080i, or 1080p signals through the HDMI or Component video port,
the aspect ratio is automatically selected and you cannot change it.
If you display a 4:3 image using the Zoom setting, the top and bottom will be cut off. You can use
the Zoom Caption Pos. option and other settings to resize and reposition the image. For details,
see page 46.
For details on how the projector resizes the picture when you choose an Aspect setting, see
page 68.
Aspect
button
4:3 image using Normal setting 16:9 image using Zoom setting
Making Basic Adjustments 29
Choosing the Color Mode
You can change the Color Mode to automatically adjust brightness, contrast, and color,
letting you quickly optimize the projected image for various lighting environments. You can
also select a different color mode for each input source—which is useful if you view different
types of images from different sources. (For example, you might set the HDMI 1 source to
Natural if it’s usually used for watching movies in the daytime with the blinds closed, and the
PC source to Dynamic for playing video games with the blinds open.)
Select the image source you want to adjust, then press the
Color Mode button on the remote
control. Choose from these settings:
■Dynamic for projecting the brightest picture available.
■Living Room for watching television programs during
the day.
■Natural for projecting natural, accurate colors in a
dimly lit room.
■Theatre for viewing movies in a dimly lit room.
■Theatre Black 1 for images that are close to those in
professional-use broadcast monitors. Use in a fully
darkened room.
■Theatre Black 2 to emphasize rich colors, like those seen in movies at the theater. Use in
a fully darkened room.
■x.v.Color for the most natural color reproduction when viewing movies through HDMI.
The built-in Epson Cinema Filter automatically improves color reproduction in a darkened
room; it is not used when you select
Dynamic or Living Room.
Color
Mode
button
30 Making Basic Adjustments
Advanced Color Adjustments
To further customize the color and image quality, you can adjust the gamma and individual
RGBCMY color tones. (Not available when x.v.Color is selected as the Color Mode.)
Note: You can fine-tune these and other color and image quality settings using the projector’s
menu system (see page 33). picture settings with the Memory You can also save combinations of
feature for easy recall (see page 43). If you don’t selected on a particular like the settings you have
menu screen, you can press the Default button to restore the factory settings.
Adjusting the Gamma Setting
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your
image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to
blur the bright areas. Higher values will darken the light areas. Gamma presets make minor
adjustments to mid-tone values. The larger the gamma preset, the lower the midtone values.
Changing these settings affects contrast which can be seen as a blur in bright areas.
1. Press the Gamma button. You see the following displayed on the screen:
Gamma
RGBCMY
Making Basic Adjustments 31
2. Do one of the following:
■Select one of the numeric correction values using the u or d button on the remote
control and press the Enter button. You see the setting reflected in the graph on the
right. The horizontal axis represents the input signal level, and the vertical axis
represents the output signal level. Press the
Gamma button to exit.
■Select Customized. Then continue with the next step.
3. Do one of the following:
■Select Adjust it from the image. You see a gamma icon on the projected image. Use
the arrow buttons to move the icon to the area of brightness you want to adjust, then
press Enter. The custom gamma graph appears with the channel selected for
adjustment. Press the u or d button to adjust and then press
Enter.
■Select Adjust it from the graph. When the gamma graph appears, use the l or r
button to select the point on the graph that you want to adjust, and then use the
u dor button to adjust the settings. Press
Enter to save your setting and exit.
Adjusting RGBCMY
Use this feature to adjust the hue, saturation, and brightness for each of the red (R),
green (G), blue (B), cyan (C), magenta (M), and yellow (Y) color components.
1. Press the RBGCMY button. You see the following displayed on the screen:
2. Use the u or d button on the remote control to select the color you want to adjust, and
press the Enter button.
3. Select the Hue, Saturation, or Brightness for that color, and use the l or r button to
make the adjustment.
4. Press Esc to adjust another color, or press RGBCMY to exit.
Note: You can also adjust the offset and gain using the RGB setting in the projector’s menu
system (see page 41).
32 Making Basic Adjustments
Locking the Projector
The projector includes two lock settings to prevent the image from being accidentally
changed once it’s adjusted, and to keep children from turning on the projector without adult
supervision.
To access the lock settings, follow these steps:
1. Press the Menu button on the remote control.
2. Use the menu navigation buttons to open the
Settings
menu.
3. Choose from these options:
■Child Lock to disable the Ppower button on the
projector’s control panel unless it is pressed for
about 3 seconds. (You can use the Ppower button
to turn it off, however.) Since you can still use the
remote control to turn on the projector, you may
want to keep it away from children’s reach.
■Control Panel Lock to disable all the buttons on the projector’s control panel. A
lock icon appears on the screen whenever you press a button with Control Panel
Lock turned on. To operate the projector, you must use the remote control. To
cancel Control Panel Lock, press and hold the
Enter button on the projector’s
control panel for at least 7 seconds.
4. Press Menu to exit the menu system.
If you turned on the Control Panel Lock, the projector buttons are now locked.
If you turned on the Child Lock, turn off the projector and let it cool down. The Child
Lock takes effect after the cool-down period.
Caution: If the Direct Power On setting is turned on (see page 47), using the main power
switch can cause the projector to start even though the Child Lock is in use.
Menu
button
Menu
navigation
buttons
Making Detailed Adjustments 33
Making Detailed Adjustments
You can use the projector’s on-screen menus to make detailed adjustments to the image
quality—such as the brightness, contrast, sharpness, and color. You can also change the menu
display, sleep mode settings, and other projector features.
Using the Menu System
You can access the menu system either from the remote control or the buttons on the
projector’s control panel. You can access the full menu or a line menu that lets you change
selected settings. You can also change the menu language and control how the menus display
(see page 35).
Note: If you press Blank on the remote control while a menu is being displayed, the menu screen
disappears. This is useful for checking the effects of your image adjustments. Press Blank again
to make the menu reappear.
1. To display the full menu, press the Menu button on the projector or remote control. You
see a display like this one:
Note: You may see different options, depending on your projector model and how your
equipment is connected to it.
2. Press the u or d button to highlight a main menu option (Image, , Signal, Settings
Memory, Info or Reset), then press the Enter button to select it.
3. Press the u or d button to highlight a setting, then press the
Enter button.
Main menu
options
Settings available
for the highlighted
menu
34 Making Detailed Adjustments
4. Press the u d l, , , or r button to change settings as necessary. You may have to press the
Enter button to confirm your choice.
5. When you’re finished, press the Esc button to return to the previous menu or press the
Menu button to exit the menu system.
To display one of the line menus, press the Enter button. You see a display like this at the
bottom of the image:
Press the u or d button to select the setting you want to adjust:
■Brightness (see page 36)
■Contrast (see page 36)
■Sharpness (see page 37)
■Color Saturation (see page 40)
■Tint (see page 40)
■Absolute Color Temperature (see page 40)
■Skin Tone (see page 40)
Press the l or r button to adjust the setting. Press the
Menu or Esc button to close the line
menu when you’re done.
Note: When a line menu is displayed, you can press Default on the remote control to reset the
menu to its factory setting.
Making Detailed Adjustments 35
Changing How the Menus Display
Use these options to control how the menus display.
■Language
Select from 21 languages to use in the menu system.
■Menu Position
Use the arrow buttons to choose a position on the screen for displaying the menu.
■Menu Color
Select a color scheme for displaying the menus.
Adjusting the Picture Quality
Before fine-tuning the image using these adjustments, make sure you have already selected the
best Color Mode for your picture and viewing environment, as described on page 29. Then
use the settings in this section to finish adjusting the picture to your liking.
Most image quality settings are saved independently for each input source (Video, S-Video,
HDMI, Component, PC) and color mode. After you finish adjusting the settings for one
input source, switch to the other input sources you’ll be using and make any necessary
adjustments.
Input Brightness Settings
If the signal from connected equipment is weak and images appear dark, you can adjust the
Brightness and Contrast settings. You can adjust brightness and contrast for each image
source and color mode.
The Brightness setting controls how much light is produced by the projector, and the
Contrast setting adjusts the difference between the bright and dark areas of the projected
image. The other settings in this section control how the projector interprets the light and
dark areas of the picture.
Settings > Language
Settings > Display > Menu Position
Settings > Display > Menu Color
36 Making Detailed Adjustments
■Brightness
Adjust the brightness so it’s suitable for your viewing conditions. For example, if you’re
projecting in a brightly lit room or onto an especially large screen, you may need to
increase the brightness. Decrease the brightness for dark rooms or small screens; this also
reduces power consumption and fan noise, and helps to prolong the life of the lamp.
■Contrast
This setting adjusts the difference between bright and dark areas.
■Auto Iris
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
When this setting is on, the amount of light produced by the lamp is automatically
adjusted according to the brightness of the image. Select either Normal or High Speed
to indicate how quickly you would like the lamp to respond to changes in the brightness
of the image. The setting is stored separately for each image source and color mode.
■Setup Level
Note: This setting can be used only when an NTSC signal is being input through the Video or
S-Video port, or when a video signal is being input through the Component video ports.
This setting adjusts the threshold at which dark areas of the image are rendered black
(0 IRE). For compatibility with most DVD and video equipment sold in the United
States, leave this setting at 0%. Check your video equipment’s specifications to be sure of
the correct setting.
■EPSON Super White
Note: This setting can be used only when a composite video, S-Video, or component video
signal is being input and the Color Mode is set to Natural, Theatre, Theatre Black 1, or Theatre
Black 2 (see page 29).
If bright parts of the image are washed out or overexposed (when the input signal
contains values over 100 IRE), turn this setting on to compensate.
Image > Brightness
Image > Contrast
Image > Auto Iris
Signal > Advanced > Setup Level
Signal > Advanced > EPSON Super White
Making Detailed Adjustments 37
■HDMI Video Range
Note: This setting can be used only when HDMI1 or HDMI2 is selected as the image source
(see page 24). This setting cannot be used when the Color Mode is set to x.v. Color (see
page 29).
If your video equipment has an HDMI port and you’ve connected it to the projector
using an HDMI cable, set the level of the projector to match that of the video equipment.
■Brightness Control
This setting controls the light output from the projector. On high, the projector produces
a brighter image and the lamp uses more power. To save power and extend the life of the
lamp, select the low brightness setting.
Sharpness and Picture Quality Settings
If the image looks fuzzy, or if it contains noise or flickering, you can use these settings to
correct it.
■Sharpness
Use this function to make lines and edges appear more distinct in the image. This setting
is stored separately for each image source and color mode setting. You can select
Standard to adjust the sharpness of the entire image, or select Advanced to access the
following submenu:
Note: The Advanced setting cannot be used with a signal input through the PC port.
Choose Thin-Line Enhancement to sharpen details such as hair and clothing. Choose
Thick-Line Enhancement to sharpen large contours and backgrounds.
You can also access this setting by pressing the Sharpness button on the remote control.
Signal > Advanced > HDMI Video Range
Image > Brightness Control
Image > Sharpness
38 Making Detailed Adjustments
■Progressive
Converts interlaced to progressive signals. The projector uses 3D DigiScan
™ HD
Circuitry Processing for video-sourced images. For film-sourced images, you can select
from 2-3, 2-2, or 4-4 pulldown detection, depending on your model.
Leave the setting on Film/Auto (Home Cinema 6100) or Auto (Home Cinema
6500 UB) for viewing movies on a player that produces interlaced output. Select Video
for watching videos captured with a video camera. With the Home Cinema 6100, set to
Off when viewing images with a large amount of movement. With the Home Cinema
6500 UB, set to Film if flickering appears with the Auto setting.
Note: This setting can be used only when viewing composite video or S-video signals, or 480i
or 576i, or 1080i signals input through the Component, HDMI 1, or HDMI 2 ports (see page 68).
This setting cannot be changed while the setting is turned on (see page 39).4-4 Pull-down
■Motion Detection (Home Cinema 6100 only)
This setting specifies how signals are converted to progressive signals. Select a lower
setting for slow-moving or still images (S) or select a higher number for video images
(M).
Note: This setting can be used only when viewing composite video or S-Video signals, or 480i
or 576i, or 1080i signals input through the Component, HDMI 1, or HDMI 2 ports (see page 68).
■Noise Reduction
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29) or
with a signal input through the PC port.
This setting reduces flickering of analog images. You can select from 3 levels of noise
reduction.
■Mosquito NR (Home Cinema 6500 UB only)
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29) or
with a signal input through the PC port.
This setting reduces grainy noise that can appear around the edges of MPEG images. You
can select from 3 levels.
Signal > Progressive
Signal > Motion Detection
Signal > Advanced > Noise Reduction
Signal > Advanced > Mosquito NR
Making Detailed Adjustments 39
■Block NR (Home Cinema 6500 UB only)
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29) or
with a signal input through the PC port.
This setting reduces block noise that can appear when projecting MPEG images that have
been compressed at a low bit rate.
■2-2 Pull-down (Home Cinema 6100 only)
Note: This setting can be used only when viewing a 1080p/24Hz signal input through the
Component, HDMI1, or HDMI2 ports (see page 68). This setting cannot be used when the
Color Mode is set to x.v. Color (see page 29) or with a signal input through the PC port.
This setting allows you to select whether images are projected with 2-2 pulldown
detection or 2-3 pulldown detection. Select On for 2-2 pulldown detection.
■4-4 Pull-down (Home Cinema 6500 UB only)
Note: This setting can be used only when viewing NTSC, M-PAL, or PAL60 signals input
through the Video or S-Video ports, or 480i, 1080i/60Hz, or 1080p/24Hz signals input through
the Component, HDMI1, or HDMI2 ports (see page 68). This setting cannot be used when the
Color Mode is set to x.v. Color (see page 29) or with a signal input through the PC port.
This setting allows you to select whether images are projected with 4-4 pulldown
detection or 2-3 pulldown detection. Select On for 4-4 pulldown detection.
■Frame Interpolation (Home Cinema 6500 UB only)
This setting compares the current and previous frames, then creates a frame between
them to reduce fuzziness and produce clearer moving images. You can select from 3 levels
of frame interpolation.
Note: This setting cannot be changed while the 4-4 Pull-down setting is turned on.
Signal > Advanced > Block NR
Signal > Advanced > 2-2 Pull-down
Signal > Advanced > 4-4 Pull-down
Signal > Frame Interpolation
40 Making Detailed Adjustments
Color Settings
If the image colors don’t look correct, you can adjust them using these settings. Use the first
three settings described below to make the most visible changes. If you only need to make
slight adjustments, you can fine-tune the picture with the remaining settings. Most color
settings are stored separately for each image source and color mode.
■Color Saturation
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29) or
with a signal input through the PC port.
Adjusts the color intensity of the image.
■Tint
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29) or
with a signal input through the PC port.
Shifts the color balance between magenta and green.
■Abs. Color Temp.
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
Shifts the color balance between red and blue, making the image appear warmer or
cooler.
■Skin Tone
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
Makes fine adjustments to the tint and controls the amount of magenta or green in the
image. Also useful for correcting black-and-white images, if they look tinted.
Image > Color Saturation
Image > Tint
Image > Abs. Color Temp.
Image > Skin Tone
Making Detailed Adjustments 41
■RGB
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
Use the RGB settings to fine-tune the color of the image. You can adjust the offset and
gain for each signal color (red, green, and blue). Use Offset to adjust darker shades and
Gain for the lightest shades.
■RGBCMY
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
Use the RGBCMY settings to adjust the hue, saturation, and brightness of the six color
components (red, green, blue, cyan, magenta, yellow). After adjusting each color, press
Esc to move to another menu option. You can also access this setting by pressing the
RGBCMY button on the remote control. See page 31 for more information.
■Gamma
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from
your image or a displayed graph. Lower values will increase the contrast of dark areas, but
tend to blur the bright areas. Higher values will darken the light areas.
You can also access this setting by pressing the Gamma button on the remote control.
See page 30 for more information.
Image > Advanced > RGB
Image > Advanced > RGBCMY
Image > Advanced > Gamma
42 Making Detailed Adjustments
■Contrast Enhancement (Home Cinema 6500 UB only)
Note: This setting cannot be used when the Color Mode is set to x.v. Color (see page 29).
This setting automatically enhances contrast by calculating based on the current contrast.
You can select from 3 levels of contrast enhancement.
Adjustments for Computer Images
In addition to the settings described previously, you can adjust the Tracking and Sync settings
for analog RGB computer images. Normally, these settings are adjusted automatically by the
projector. If you notice that the image is blurry or contains dark vertical bands, you may need
to adjust the settings yourself.
■Auto Setup
Leave this setting on so that the projector automatically adjusts the tracking, sync, and
position of the image.
■Tracking
Adjust the tracking to eliminate vertical bands. It is easiest to
adjust the tracking when the image contains a lot of fine detail
(such as black text on a white background).
■Sync.
Adjust the synchronization to eliminate blurriness. For best results,
make sure the tracking is properly adjusted first.
Image > Advanced > Contrast Enhancement
Signal > Auto Setup
Signal > Tracking
Signal > Sync.
Making Detailed Adjustments 43
Selecting Memory Settings and Resetting the
Projector
Your projector comes with 10 memory locations for installers to save customized settings,
designed to provide the best color quality for each of your video inputs.
Selecting Memory Settings
You can easily recall the memory settings by using the
memory button on the remote control.
1. Press the Memory button on the remote control.
2. Select Load Memory.
3. Use the arrow buttons to select the desired setting, then
press the Enter button.
After a moment, the image appears on the screen using
your selected setting.
Creating Memory Settings
Memory settings store the Brightness and Contrast settings, Color Mode, Auto Iris,
Brightness Control, Sharpness, and other color settings described on page 40.
1. Press the Memory button on the remote control.
2. Select Save Memory.
3. Select the memory name you want to use, then press the Enter button to save your
settings.
Note: Saved settings are indicated by a green highlight next to the memory name. If you select
a name that is already in use, the existing settings will be erased and new ones saved in their
place.
Memory
button
44 Making Detailed Adjustments
Renaming Memory Settings
With the Home Cinema 6500 UB, you can rename memory settings so that they are easier
for you to recognize.
1. Press the Memory button on the remote control.
2. Select Rename Memory.
3. Select the memory name you want to change, then press the Enter button. The name
selection screen is displayed.
4. Do one of the following:
■To select a name from the displayed preset names, select the desired name and press
the Enter button.
■To create your own name, select Customized and use the keyboard screen to enter
the name. Use the arrow buttons to select a character, then press the Enter button.
When you have selected all of the characters in your name, select Finish and press the
Enter button.
Deleting Saved Memory Settings
You can clear all your memory settings at once.
1. Press the Menu button on the remote control.
2. Open the Reset menu, then select Reset Memory.
3. Select Yes, then press the Enter button to delete the memory settings.
Note: You can delete memory settings one at a time with the Erase Memory setting under the
Memory menu.
Making Detailed Adjustments 45
Resetting the Projector
If the image quality isn’t what you expect, one or more settings may be adjusted improperly.
If necessary, you can restore the projector to its factory-default (original) settings.
To restore the settings in a specific menu (such as the Image or Settings menu), open that
menu, select Reset, and confirm as needed. The example below shows how to reset the
Image menu settings:
You can also reset the lamp usage timer or restore all the projector settings to their original
values. Follow these steps:
1. Press the Menu button on the remote control.
2. Open the Reset menu.
3. Do one of the following:
■Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero.
You should reset the lamp timer only when you install a new projector lamp. See
page 55 for more information.
■Select Reset Memory to clear all memory settings.
■Select Reset All to return all projector settings to their original defaults (except
Component, Save Memory, Language, and Lamp).
Open the Image
menu . . .
and select Reset
46 Making Detailed Adjustments
Customizing Projector Features
Use the settings in this section to adjust the image size and position, suppress on-screen text,
and select basic setup options.
Image Sizing
Before adjusting any of these settings, make sure you have already selected an appropriate
aspect ratio for the type of picture you’re viewing (see page 28).
■Output Scaling
For component video formats, this setting lets you see the edges of the image that are not
normally visible in the picture (see page 68). If you see interference when you set
Output
Scaling to 100%, try adjusting the Position as described below.
■Position
Note: This setting cannot be used with a signal input through the HDMI 1 or HMDI 2 port.
Use the arrow buttons to fine-tune the position of the image on the screen.
■Aspect
This setting lets you change the aspect ratio of your image, and works the same as
pressing the Aspect button on the remote control. See page 28 for more information.
■Zoom Caption Pos.
Lets you adjust the shape and position of the image so that subtitles are visible (available
only if the aspect ratio has been set to Zoom). Use Zoom Size to adjust the proportions
of the image, and Zoom Caption Pos. to move the image up or down. You can adjust
output scaling before zoom position.
Signal > Advanced > Output Scaling
Signal > Position
Signal > Aspect
Signal > Zoom Caption Pos.
Making Detailed Adjustments 47
Screen Options
■Messages
Turn this setting off if you want to prevent on-screen messages from appearing (such as
the no-signal message, or the identifying text that appears when you switch between
image sources or color modes).
■Startup Screen
Turn this setting off if you want to prevent the startup screen from appearing while the
projector is warming up.
■Display Background
Changes the screen that’s used when the projector is not receiving a signal or when you
press the Blank button to temporarily stop projection.
Other Setup Options
■Projection
You can select different options for projecting the image: Front, , Front/Ceiling, Rear
Rear/Ceiling.
■Direct Power On
Sets projection to start when the main power switch is turned on, without pressing the
Ppower button on the remote control or the projector.
Note: When direct power on is enabled, power surges that occur after a power outage can
cause the projector to turn on.
■Video Signal
Leave this setting on Auto so the projector can automatically interpret the format, such as
NTSC or PAL (for standard TV formats).
Settings > Display > Messages
Settings > Display > Startup Screen
Settings > Display > Display Background
Settings > Projection
Settings > Direct Power On
Settings > Input Signal > Video Signal
48 Making Detailed Adjustments
■Component
Change this setting to match the type of equipment connected to the Component port.
For component video, select Auto to let the projector automatically interpret the signal;
or select YCbCr or YPbPr to manually select your video equipment’s signal.
■Trigger Out
Turn on this setting if you want the Trigger out port to output a 12-volt signal while
the projector is operating. You can use this to raise or lower your projection screen.
Note: If you change this setting, the new setting will take effect the next time you turn the
projector on.
■Sleep Mode
Turn off this setting if you don’t want the projector to enter sleep mode. (Sleep mode
shuts the projector off automatically when there is no video signal.)
Select 5min., 10min., or 30min. as the length of time before shutoff; decreasing the time
conserves power and extends the life of the lamp.
To turn the projector back on, press the Ppower button on the remote control or the
projector.
■Child Lock
Lets you lock the ntrol panel to make it more Ppower button on the projector’s co
difficult for a child to turn on the projector. See page 32 for more information.
■Control Panel Lock
Lets you disable all the buttons on the projector’s control panel to prevent the image from
being accidentally changed once it is adjusted. See page 32 for more information.
■High Altitude Mode
Adjusts the speed of the fan so it can properly cool the projector at higher altitudes. Turn
this setting on if you are using the projector at an altitude of 4900 feet (1500 meters) or
higher.
Settings > Input Signal > Component
Settings > Trigger Out
Settings > Sleep Mode
Settings > Child Lock
Settings > Control Panel Lock
Settings > High Altitude Mode
Maintenance 49
Maintenance
Your projector needs little maintenance. All you need to do on a regular basis is keep the lens
clean. You also may need to clean the air filter to prevent overheating.
Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never
open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages
in the projector can injure you severely. Do not try to service this product yourself, except as
specifically explained in this User’s Guide.
The only parts you should replace are the air filter and the lamp. If another part needs
replacing, contact your dealer or a qualified servicer.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on
the surface.
■Use a blower brush that is designed for camera
equipment to remove dust from the lens.
■To remove dirt or smears, use a lens cloth or
tissue. If necessary, moisten the cloth with lens
cleaner and gently wipe the lens surface.
Caution: Never rub the lens with abrasive materials. Use
only lens cleaning fluids that are designed for cleaning
optics.
50 Maintenance
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case
with a soft, dry, lint-free cloth.
■To remove stubborn dirt or stains,
moisten a soft cloth with water and a
neutral detergent. Then wipe the case
and dry it with a dry cloth.
Caution: Never use wax, alcohol, benzene,
thinner, or other chemical detergents. These
can damage the case.
Cleaning and Replacing the Air Filter
Your projector includes an air filter to ensure the best performance. If dust collects on the air
filter, clean it as described below. Dust clogs prevent proper ventilation and cause overheating
and damage to the projector.
1. Press the P Power button and wait for the PPower light to stop flashing. The projector
cools down.
2. Turn off the projector using the power switch on the back.
3. Unplug the power cord and disconnect any cables.
4. Turn the projector over (unless it’s ceiling mounted).
5. Push down on the tabs on the filter cover to remove it.
6. Remove the air filter as shown.
Maintenance 51
7. Gently tap both sides of the air filter against a hard surface
four or five times to remove loose dust from the air filter.
Note: Do not tap the filter too hard. This can cause it to bend
or break.
8. Use a small vacuum cleaner that is designed for computers
and other office equipment to remove any remaining dust
from the surface of the filter. If you don’t have one, gently
clean the filter using a very soft brush (such as a clean
artist’s paintbrush).
If the dirt is difficult to remove or the filter is broken,
replace it. You can purchase air filter part number V13H134A21 (ELPAF21) from an
authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON
(800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales) or
www.epson.ca (Canadian sales).
9. Insert the air filter as shown with the groove on the right.
10. Reattach the air filter cover by inserting the tabs as shown and pressing the cover against
the projector until it clicks into place.
52 Maintenance
Replacing the Lamp
The projection lamp lasts for up to 4000 hours. You can use the Info menu to check how
long it’s been in use (see page 55). It’s time to replace the lamp when:
■The projected image gets darker or starts to deteriorate.
■The projector’s lamp light flashes red at half-second
intervals.
■The message Replace the lamp appears on the screen
when you start projecting.
Note: Lamp life results will vary depending on mode selected,
environmental conditions, and usage.
Turn off this product when not in use to prolong the life of the projector.
You can purchase lamp part number V13H010L49 (ELPLP49) from an authorized Epson
reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To
purchase online, visit www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Be sure to read the “Important Safety Information” on page 71 before replacing the lamp.
Warning: Let the lamp cool fully (about 1 hour) before replacing it. In the unlikely event that the
lamp has broken, small glass fragments may be present and should be removed carefully to avoid
injury.
Caution: Never touch the glass portion of the lamp with your bare hands; the invisible residue left
by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Follow these steps to replace the lamp:
1. If the projector is on, press the P
Power button and wait for the light to stop flashing.
2. Turn off the power switch on the back of the projector.
3. Unplug the power cord and any cables.
4. Wait about an hour to make sure the lamp is no longer hot.
Lamp
light
Maintenance 53
5. Insert the screwdriver that came with the lamp (or a similar tool) into the slot on the back
of the projector to release the lamp cover. Then lift up the cover to remove it.
6. Loosen the two screws securing the lamp (they don’t come all the way out).
7. Grasp the bottom of the lamp as shown and pull it straight out.
Warning: The lamp(s) in this product contain mercury. Please consult your state and local
regulations regarding disposal or recycling. Do not put in the trash.
54 Maintenance
8. Gently insert the new lamp and tighten its screws.
Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result
in premature lamp failure.
9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.)
10. Reset the lamp usage timer, as described on page 55.
Maintenance 55
Resetting the Lamp Usage Timer
After replacing the lamp, plug the projector back in, turn on the power switch on the back,
and press the P Power button. Then follow these steps to reset the lamp usage timer:
1. Press the Menu button on the projector or remote control.
2. Use the menu navigation buttons to open the Reset menu, then select Reset Lamp
Hours .
3. When you see a confirmation prompt, highlight Yes and press the Enter button.
4. When you’re finished, press the Menu button to exit.
The lamp usage timer shows 0H until you’ve used the lamp for at least 10 hours.
Checking the Projector Status
You can use the Info menu to view information about the current display settings and how
long the projection lamp has been in use. To access the Info menu:
1. Press the Menu button on the projector or remote control.
2. Use the menu navigation buttons to open the Info menu. The following information
appears:
Note: The information displayed depends on the currently selected image source. The Lamp
Hours shows 0H until you’ve used the lamp for at least 10 hours.
The resolution indicates the total number of scan lines in the source signal. The number of visible
scan lines depends on the signal format standard and selected display settings (see page 68).
■ ■Lamp Hours Refresh Rate
■ ■Source Sync Info
■ ■Input Signal Video Signal
■Resolution ■Deep Color (color depth)
■ ■Scan Mode Status (error information)
56 Maintenance
Storing the Projector
If you need to store the projector for an extended time, do the following:
■Make sure the temperature of the storage area is within 14 to 140 °F (–10 to 60 °C).
■Attach the lens cover and retract the feet.
■Remove the batteries from the remote control.
■Pack the projector in its original packaging or equivalent.
Transporting the Projector
Note: Epson shall not be liable for any damages incurred during transportation.
The projector contains many glass and precision parts. When shipping the projector for
repairs, use the original packaging material if possible. If you do not have the original
packaging, use equivalent materials. Do not used materials that can become lodged in the
projector vents. Be sure the carrier is capable of transporting fragile equipment and is aware
that the projector is fragile.
Before transporting the projector, make sure you center the lens from left to right by turning
the horizontal lens shift dial until it clicks. Then lower the lens all the way down by turning
the vertical lens shift dial until it stops.
Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the
lens shift dials to change the lens position. If the lens shift dial becomes hard to turn, you cannot
adjust the position any further.
Problem Solving 57
Problem Solving
This section explains how to interpret the projector’s status lights, solve problems with the
picture and remote control, and contact technical support.
What To Do When the Lights Come On
or Flash
The lights on top of the projector indicate the projector’s
status and let you know when a problem occurs.
If the projector isn’t working correctly, first press the
P power button, let the projector cool down, turn off the
power switch on the back, and unplug the power cord.
Then plug the power cord back in and turn on the
projector. If this doesn’t solve the problem, check the
status lights on top of the projector.
Lights indicating normal operation
Light state Cause and solution
All lights are off The projector is turned off. If necessary, connect the power cord
and turn on the power switch on the back of the projector.
Power icon is on The projector is in standby mode. Turn off the power switch in
back to turn off the projector, or press the Ppower button to turn
it on.
Power button
flashes and
icon is on
The projector is warming up. Wait for the picture to appear.
Power icon and icon
are on
Projection is in progress.
Power button
flashes; no other
lights are on
The projector is cooling down. Wait until the light stops flashing
and remains on. Then turn off the power switch in back to turn off
the projector, or press the Ppower button to turn it back on.
Operation
indicator
lights
Warning lights
58 Problem Solving
Lights indicating a problem
Light state Cause and solution
All lights are off The projector is not receiving power. Make sure the power switch
on the back of the projector is turned on and the power cord is
connected securely at both ends.
The temperature
light flashes
orange and the
power icon is
flashing
High-speed cooling is in progress. If the temperature rises
further, projection will stop automatically. Make sure there is
plenty of space around the projector for ventilation. Clean or
replace the air filter if necessary (see page 50).
If you are using the projector at an altitude above 4900 feet (1500
meters), turn on High Altitude Mode so the fan can cool the
projector properly (see page 48).
The temperature
light is red
The projector is too hot, which turns off the lamp automatically.
Let the projector cool for five minutes, then turn it back on. Make
sure there is plenty of space around the projector for ventilation.
Also, clean or replace the filter if necessary (see page 50).
If you are using the projector at an altitude above 4900 feet (1500
meters), turn on High Altitude Mode so the fan can cool the
projector properly (see page 48).
The lamp light
flashes orange and
the power icon
is flashing
The lamp needs to be replaced soon (see page 52). Make sure
you have a spare lamp handy. If you just replaced the lamp, you
may need to reset the lamp usage timer (see page 55).
The lamp light
flashes red
The lamp needs to be replaced. If you just replaced the lamp,
make sure the lamp and its cover are securely installed (see
page 52).
Both warning
lights are flashing
red
There is a problem with the auto iris or cinema filter. Turn off the
power switch on the back of the projector, and unplug it from the
electrical outlet. Then contact Epson for assistance (see page 63).
The temperature
light flashes red
There is a fan or sensor problem. Turn off the power switch on
the back of the projector, and unplug it from the electrical outlet.
Then contact Epson for assistance (see page 63).
Both warning lights
are red
There is an internal problem. Turn off the power switch on the
back of the projector, and unplug it from the electrical outlet.
Then contact Epson for assistance (see page 63).
Problem Solving 59
Solving Picture Problems
You cannot turn on the projector.
■Make sure the power cord is connected and the power switch in back of the projector is
turned on. Then wait a moment for the Ppower icon to light up before pressing the
Ppower button.
■If you’ve set the Operation Lock, the control panel buttons are disabled; you must use
the remote control to turn on the projector (see page 32).
■If you’ve set the Child Lock, you have to press the Ppower button for 3 seconds to turn
on the projector, or use the remote control (see page 32).
No picture appears on the screen or you see the No Signal message displayed.
■Press one of the Source buttons on the remote control, or press the source button
on the projector, to select the correct input source. Allow a few seconds for the projector
to sync up after pressing the button.
■Press the Blank button on the remote control to make sure the picture hasn’t been turned
off temporarily.
■Check that the P Ppower icon is lit, the power button is not flashing, and the lens cover
is off.
■The projector may be in standby (or sleep) mode. If the Ppower icon is lit, press the
Ppower button to turn the projector back on.
■Make sure your video equipment is turned on.
■Make sure your cable(s) are connected correctly (see page 19).
Only part of the picture is displayed, or the picture is distorted.
■Press the Aspect button to select a different aspect ratio (see page 28).
■If the Aspect is set to Zoom, you may need to use the Zoom Caption Pos. option to see
the top or bottom section of the screen so that subtitles are visible (see page 46).
■Check the Output Scaling to make sure it’s adjusted correctly (see page 46).
■Use the Position setting to reposition the image on the screen (see page 46).
■If you’ve connected a computer and you see only half the image, make sure the
computer’s Dual Display setting is turned off. If part of the image is cut off, reset the
projector settings (see page 45).
Produktspezifikationen
Marke: | Epson |
Kategorie: | Beamer |
Modell: | PowerLite 6100 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Epson PowerLite 6100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Beamer Epson
14 Oktober 2024
13 Oktober 2024
10 Oktober 2024
9 Oktober 2024
7 Oktober 2024
26 September 2024
22 September 2024
14 September 2024
5 September 2024
5 September 2024
Bedienungsanleitung Beamer
- Beamer Samsung
- Beamer 3M
- Beamer Acer
- Beamer Anker
- Beamer Asus
- Beamer Sanyo
- Beamer BenQ
- Beamer Hama
- Beamer HP
- Beamer Medion
- Beamer Philips
- Beamer Sony
- Beamer Panasonic
- Beamer LG
- Beamer OK
- Beamer Canon
- Beamer Technaxx
- Beamer Renkforce
- Beamer Blaupunkt
- Beamer Sharp
- Beamer Pyle
- Beamer Mitsubishi
- Beamer Hisense
- Beamer Salora
- Beamer Aiptek
- Beamer Auna
- Beamer Lenco
- Beamer JVC
- Beamer Optoma
- Beamer Xiaomi
- Beamer Stairville
- Beamer Smartwares
- Beamer Hitachi
- Beamer Toshiba
- Beamer Livoo
- Beamer Casio
- Beamer ViewSonic
- Beamer Dell
- Beamer Lenovo
- Beamer Ricoh
- Beamer Smart
- Beamer Kodak
- Beamer Leica
- Beamer Adj
- Beamer Vogel's
- Beamer Eurolite
- Beamer Showtec
- Beamer Barco
- Beamer Bauer
- Beamer Eiki
- Beamer InFocus
- Beamer Nebula
- Beamer NEC
- Beamer Overmax
- Beamer Marantz
- Beamer Kogan
- Beamer Acco
- Beamer Elmo
- Beamer D-Link
- Beamer Smart Tech
- Beamer Reflecta
- Beamer ZTE
- Beamer Derksen
- Beamer Cameo
- Beamer Yaber
- Beamer Vivitek
- Beamer RCA
- Beamer Promethean
- Beamer GPX
- Beamer Ibm
- Beamer La Vague
- Beamer Maxell
- Beamer Naxa
- Beamer PLUS
- Beamer Steren
- Beamer XGIMI
- Beamer Planar
- Beamer Dahua Technology
- Beamer Tzumi
- Beamer Christie
- Beamer Atlantis Land
- Beamer EKO
- Beamer Varytec
- Beamer ASK Proxima
- Beamer Beghelli
- Beamer Laserworld
- Beamer Vankyo
- Beamer AAXA Technologies
- Beamer Knoll
- Beamer Boxlight
- Beamer Miroir
- Beamer MicroVision
- Beamer Ultimea
- Beamer Dukane
- Beamer Dream Vision
- Beamer Touchjet
- Beamer AWOL Vision
- Beamer KickAss
- Beamer VAVA
- Beamer Panamorph
Neueste Bedienungsanleitung für -Kategorien-
15 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
13 Oktober 2024
12 Oktober 2024
11 Oktober 2024
11 Oktober 2024
10 Oktober 2024
9 Oktober 2024