Electrolux EIDW6105G Bedienungsanleitung

Electrolux Spülmaschine EIDW6105G

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Electrolux EIDW6105G (2 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 40 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Before You Begin

Read all instructions before installing dishwasher.

For your safety, please read and observe all safety

instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the

dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Failure to follow this warning can result in serious

injury.

Installation Tips

Tools and Materials Needed for

Installation (Not Included)

• Drill, Electric

• Driver, Socket 5/32 ”,

1/4” , 5/16”

• Flaring Tool / Tube Cutter (for copper tubing)

• Flashlight

• Level

• Pipe Joint Compound (for iron pipe plumbing) or

Pipe Thread Tape (for sealing threads)

• Pliers

• Safety Glasses

• Saw, Keyhole or 1/2

”, 11/2” to 2” Hole Cutters

• Screw Drivers, Slotted and #2 Phillips (magnetic tip

preferred)

• Tape, Electrical or Duct

• Tape, Measuring

• Wire Stripper or Utility Knife

• Wrench, Hex-end

• Wrenches, 2 Adjustable (for copper tubing)

or 2 Pipe wrenches (for iron pipe plumbing)

Parts You Will Need* (Not Included)

• Drain Hose Clamp, 11

/4” Diameter

• Brass Elbow, 90° with a 3/8” National Pipe Thread

• Conduit Connector (UL Listed)

• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)

If required:

• “Y” Branch Tailpiece and

Connector Kit (See Step 4)

• Air Gap Kit (See Step 4)

All the parts can be found at local hardware, electrical and

plumbing supply stores.

Electric Shock Hazard

Electrical, water, and drain lines must be confined

to shaded areas in Figure 2.

Electric conductors, water, and drain could be

damaged.

Failure to follow these instructions could result in

fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet, sides and

back must be fully enclosed.

NOTE: Cabinet Seal Kit (Kit # 154662101) . This kit provides a

seal between the unit and cabinets once installation is

complete. (The Installation Instructions are located in the Kit)

Connections For Electrical,

Water, and Drain

Locating the Connections

1. Review dimensions in Figure 2 to locate dishwasher’s drain,

water, and electrical connections.

2. All utilities must be routed in shaded area in the Figure 2.

IMPORTANT: Disconnect power before starting installation.

Note: Locate the electrical supply and dishwasher’s electrical

3. Locate water inlet valve behind kickplate on bottom left underside

of unit.See Figure 4. The valve has a 3/8” NPT female fitting.

Remove Plug

4. Wrap 90° elbow (not included) with pipe thread tape (or apply

joint compound) and thread it into water inlet valve. When

tightened, elbow should point toward the left. To prevent bending

of bracket or breaking of valve, avoid overtightening.

See Figure 4.

NOTE: Put unit on its back being careful not to pinch the Water

Drain Hose.

1. Remove two (2) screws at front of the kickplate assembly using a

#2 Phillips screw driver.

2. Tilt and pull forward to remove see figure 1.

NOTE: It is not necessary to remove the outer door for installation.

Installation Preparation

junction box on right underside of unit behind kickplate

assembly. See Figure 4. Determine where you will connect

to hot water supply. Review Figure 4 and note the location of

water inlet valve. Determine where you will connect the drain

hose.

3. Cut access holes for the Electrical, Water and Drain hoses in the

shaded areas as shown in Figure 2.

4. The dishwasher operates on a 120 volt, 60 Hz electrical supply.

Provide a separate circuit with a fuse or circuit breaker rated for

at least 15 amps (20 amps if connected with disposer) but not

more than 20 amps.

5. Pull electrical cable through hole into installation area.

6. Be sure water inlet valve is protected from freezing. If valve

freezes and ruptures, flooding may occur.

7. Determine amount of tubing needed to connect hot water supply

to the unit’s water inlet valve. Extra hose length is necessary.

High-pressure and high-temperature Stainless Flexible hose with

a minimum inner diameter of 1/4” may be used. A shut-off valve

installed outside dishwasher cabinet is best.

8. Route water supply line into installation area.

9. Stand dishwasher back upright for further installation.

IMPORTANT: Incoming hot water temperature should be at

least 120°F (49°C). Water pressure should be between

20–90 psi.

Property Damage

Do not use the furnished drain hose or a rubber garden hose

for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

Roughing In

Electric Shock Hazard

Observe all local codes and ordinances for

electrical and plumbing connections. All electrical

and plumbing work should be performed by

qualified persons. Failure to follow this warning

could result in death or serious injury.

1. Make sure your location has the correct drain, water, and

electrical outlets to make the connections.

Do not install unit

under a cooktop range. Damage to tub or other components will

occur.

IMPORTANT: For proper operation and appearance of unit,

cabinet opening should have dimensions as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

Floor should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be

roughed-in before going any further.

INSTALLER: Leave

Installation Instructions

with owner.

OWNER: Read your dishwasher

Use and Care Manual.

It contains

important safety information for operating this appliance. It also has

many suggestions for getting the best results from your dishwasher.

Dishwasher

Installation

Instructions

Electric Shock Hazard

Disconnect electrical power at the fuse box or

circuit breaker box before beginning installation.

Failure to follow this warning could result in death

or serious injury.

Printed in U.S.A.

Cabinet Preparation:

As a precaution, it is recommended, but not required that the

cabinets enclosing all sides of the dishwasher (including the

underside of the countertop) be sealed with an oil based paint

or moisture-proof polyurethane to prevent possible steam/

moisture damage.

*DIMENSIONS DO NOT INCLUDE INSULATION

1. Measure height of cabinet opening from underside of countertop

to floor. Check chart for height opening and suggested

adjustment.

2. Move dishwasher to front of installation area.

3. Loosen the rear leveling legs by turning counterclockwise. Refer

to chart for number of turns.

Leveling and Securing

Dishwasher within

Cabinets

Number of Turns to

Adjust Levelers

Height of

Cabinet Opening

Leg Leveler Adjustment Chart

341/8” (86.7cm)

345/16” (87.2cm)

34” (86.4cm)

341/2” (87.6cm)

Dishwasher Anchoring

4. Install the Cabinet Seal Kit (Instructions included in Kit)

5. Choose one of the methods of attachment below to secure unit,

holes need to be pre-drilled using a #5 drill bit regardless of

the option chosen:

a. Side Mount Cabinet Clips (Preferred Method of attachment)

b. Top Mount Cabinet Clips (to be used when Side Mount

is not an available option)

CAUTION: Use extreme care in mounting the dishwasher as to not

scratch, bump or otherwise damage the console or tub.

To install the Side Mounting Clips.

Depending on space allowed in cabinet the Side Mounting

Clips can be installed with the holes for the screw up (preferred

method) or down as shown in the illustrations below. (Use extreme

caution when the clips are in the down position while installing

the dishwasher).

NOTE: Install Side Mount Brackets before unit is installed into

the cabinet. Insert screws into the front holes of the

mounting clips only. (See image below)

Use if measures 34

1/8” to 35”

Use if measures 34” to 34

1/8

”

To install using Top Mount Cabinet Clips:

Depending on the depth of cabinet, the Top Mount

Clip have a break off point that can be removed if

necessary.

NOTE: Install Top Mount Clips before unit is installed into the

cabinet. Screw clips firmly to top brace using screws

provided in the literature pack. (See image below)

1. Take drain Hose out of dishwasher and find the end that

doesn’t have the black rubber material.

2. Use only the spring clamp that is provided in the accessory

kit, place spring clamp over one of the hoses. See Image

Below.

3.Take the plastic side of the drain hose and insert it into the

hose that is already attached to the dishwasher make sure

hose ends are flush against each other. See image below.

4. Secure the spring clamp 1/8” from large end of black hose to

the plastic side that was inserted for best sealing results.

See Image Below.

NOTE: Pull the hose from “End Storage Location” side.

See images below to connect the Drain Hose.

Cut Hazard

To prevent serious injury from sharp edges, wear work

gloves when handling, unpacking or disassembling unit.

154671001

Outer Door

screw

02/08

Cut Hazard

Electric Shock Hazard

Disconnect electrical power at the fuse box

or circuit breaker box before beginning

installation.

Failure to follow this warning could result in

death or serious injury.

Metal color panels are sharp and should be

handled with care. Wear gloves to protect

hands.

Failure to follow this warning may result in

injury.

Checking the Installation

Operate the machine through at

least one fill and pump-out,

checking the following items:

qOn EWDW6505 press and hold SET Icon for 5 seconds

before first use. On EIDW6305 and EIDW6105 press and

hold down HI-TEMP Icon for 5 seconds before first use.

qAt first fill, approximately 2 minutes make sure water

completely covers filter surface.

qAt pump-out: (pump-out is either when the cycle is

completed or canceled. refer to the Use and Care Manual

for Start/Cancel), make sure all water is pumped out.

qCheck water connections again for leaks.

Electric Shock Hazard

If all connections are correct, there are no leaks,

and unit runs properly, replace the kickplate

assembly before placing unit into operation.

Failure to follow this warning could result in

electric shock.

check these items:

qWater and drain lines have no kinks and move freely

behind the dishwasher.

qWater supply is turned on.

qJoints are free of leaks.

qWiring connections to junction box are tight all access

panels are secured back in place.

qReplace kickplate. See Figure 1

qDrain hose is assembled to Drain Hose Connector.

qAll packing materials and consumer literature have

been removed from inside unit.

qDishwasher is level and securely fastened.

q Open and close door to make sure it does not hit

surrounding cabinet or countertop.

1. Review Figures 7, 8 and 9 to see the different ways to connect

dishwasher to drain system. Choose method that best suits

your need.

5. If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with

electrical or duct tape to avoid cutting drain hose.

3. If you connect to a sink trap, local codes may require you to

install an air gap kit, (not included). The drain hose will be routed

from dishwasher to air gap inlet as shown in Figure 8. An air

gap kit is available from a plumbing supply store. (If the drain

hose is installed through the floor, an air gap is necessary).

4. If you connect to a disposer, the large end of drain hose will fit.

Figure 9(a).

The knock out plug must be removed from

inside disposer inlet before making the final fit to drain

hose.

See Figure 9(b).

2. If you connect to a sink drain, entry will need to be above trap.

A “Y” branch tailpiece and connector kit, not included, will make

this method easier and includes all needed fittings and

instructions. See Figure 7.

Finishing the Drain

Connection

6. Move unit back in place while routing drain hose through access

hole. Use caution to prevent damage to the dishwasher, floor and

cabinets. IMPORTANT: Make sure there are no sharp bends

or kinks that might restrict drain flow.

7. Secure drain hose to sink drain, disposer, or separate trap with a

clamp. IMPORTANT: Be careful not to overtighten clamp or

you may damage end of hose. Do not connect hose to

horizontal pipe between sink drain and disposer.

8. Be sure unit does not rest on drain hose. It should be free of

electrical components and door springs. Do not cut corrugated

drain hose. Pull excess through cabinet and place under sink.

Make sure hose does not come in contact with any sharp edges.

Electric Shock Hazard

Grounding Instructions:

The dishwasher must be connected to a grounded metal,

permanent wiring system or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the appliance’s equipment grounding terminal

or lead. It is the consumer’s responsibility to contact a

qualified installer to make sure the electrical installation

conforms with the National Electrical Code and local codes

and ordinances.

Do not connect the dishwasher to the power supply until the

appliance is permanently grounded.

All wiring connections must be enclosed in the junction box.

This unit has copper lead wires.

Joining aluminum building wire to stranded copper wire

should be done by a qualified electrician using materials

recognized by UL and local codes.

Do not use an extension cord. Such use can result in fire,

electrical shock, or other personal injury.

Failure to follow these instructions could result in death or

serious injury.

Installation Diagram

check these items:

qWater and electrical lines are straight out in front of the

dishwasher.

qAll four leg levelers are positioned properly.

qCabinet Seals are positioned on the sides and top of the

dishwasher.

qCabinet Attachment Clips are attached to the cabinet on

both corners on top of the dishwasher.

2. Route water line to water inlet valve as shown in Figure 4.

3. While firmly pulling water supply line into 90° elbow, tightly

connect water supply to water inlet valve. Supply line must be

free of kinks, scales, chips, and lubricants.

4. Turn on water supply and check for leaks.

Finishing the Water and

Electrical Connection

Property Damage

Do not solder within 6” of the water inlet valve. Damage to

the plastic parts in the valve may occur.

Use care that no sealer, dirt, or other objects enter the valve.

Damage to the filter screen may occur.

Be sure the dishwasher is placed where the water inlet

valve will be kept from freezing. If the valve freezes, it may

rupture and flooding may occur.

Water Line

1. Flush water line before connecting it to water inlet valve to

prevent early clogging of filter screen.

Place a bunched towel

over end of line to prevent splashing. Open water supply valve for

a few seconds and let water drain into a pan.

Turn off water

supply at shut-off valve.

Electrical Supply

1. Remove junction box cover and pull house wiring into junction

box. See Figures Below.

2. Use a UL listed conduit connector (not included) at box to

stabilize wiring.

3. Connect incoming black lead to dishwasher’s black lead,

incoming white lead to dishwasher’s white lead and incoming

green lead to dishwasher’s green lead with wire nuts. (See

Grounding Instruction Warning). Wire nuts must be tight.

4. Replace junction box cover.

10. Check that the dishwasher is level from front to back by taking

out the lower rack, place level on the lower rack wheel support at

the bottom of the tub. See Figure 5b.

11. Adjust levelers up or down until dishwasher is level.

Holes need to be pre-drilled using a #5 drill to secure unit.

12. Screw mounting brackets firmly to cabinet using screws provided

in literature packet. See Image Below.

13. Open and close dishwasher door slowly. Ensure that there is

clearance to the console. Adjust accordingly until door opens

and closes freely.

9. Check that dishwasher is level from side to side by placing a level

against the top front section of the tub. See Figure 5a.

qReplace Toe and Kickplate. Note: When replacing Toe

and Kickplate hand tighten screws.

6. If levelers need to be removed, make sure that the floor is free of all

obstructions.

7. Carefully place dishwasher inside cabinet area such that is

centered in opening. Use caution when moving dishwasher to

prevent damage to cabinet, dishwasher and floor.

8. Front of door needs to be even with the front of adjoining cabinets.

Front levelers should allow 5/16” below underside of countertop

to top of console.

q Make sure that all wire ties are removed from the Adjustable

Rack Assembly, Versa Tray, Utility Tray and Silverware

Baskets.

Produktspezifikationen

Marke:	Electrolux
Kategorie:	Spülmaschine
Modell:	EIDW6105G

Brauchst du Hilfe?

Wenn Sie Hilfe mit Electrolux EIDW6105G benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Spülmaschine Electrolux

Electrolux EEM648310L Bedienungsanleitung

8 Oktober 2024

Electrolux EEQ47225L Bedienungsanleitung

7 Oktober 2024

Electrolux EEC987300L Bedienungsanleitung

30 September 2024

Electrolux Y69EG400L Bedienungsanleitung

28 September 2024

Electrolux ESG88500SX Bedienungsanleitung

24 September 2024

Electrolux ESF9452LOX Bedienungsanleitung

22 September 2024

Electrolux ESA12100SW Bedienungsanleitung

15 September 2024

Electrolux ESA42110SW Bedienungsanleitung

9 September 2024

Electrolux ESM48400SX Bedienungsanleitung

7 September 2024

Electrolux KECB7215L Bedienungsanleitung

5 September 2024

Bedienungsanleitung Spülmaschine

Neueste Bedienungsanleitung für -Kategorien-

Siemens 15 Bedienungsanleitung

12 Dezember 2023

Exquisit EGSP130-E Bedienungsanleitung

11 Mai 2024

BEKO BDFN26530B Bedienungsanleitung

4 Dezember 2024

BEKO BDEN38560CHPA Bedienungsanleitung

4 Dezember 2024

BEKO BDIN16520Q Bedienungsanleitung

4 Dezember 2024

BEKO BDFN15421W Bedienungsanleitung

4 Dezember 2024

BEKO BDIN15320 Bedienungsanleitung

4 Dezember 2024

BEKO BDFS15020B Bedienungsanleitung

4 Dezember 2024

BEKO BDFS15020S Bedienungsanleitung

4 Dezember 2024

BEKO BDFN15421S Bedienungsanleitung

4 Dezember 2024