ECS APLD-I Bedienungsanleitung

ECS Hauptplatine APLD-I

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für ECS APLD-I (22 Seiten) in der Kategorie Hauptplatine. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/22

APLD-I USER MANUAL

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the contents

hereof and specifically disclaims any implied warranties of merchantability or

fitness for any particular purpose. The manufacturer reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of the manufacturer to notify any person of such revision or changes.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and the receiver

•Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits

governing this device. Changes or modifications not expressly approved by the

system’s manufacturer could void the user’s authority to operate the equipment.

Federal Communications Commission (FCC)

Disclaimer

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference

that may cause undesired operation.

Electromagnetic compatibility of multimedia equipment - Emission

requirements

EN 55032

EN 61000-3-2 Electromagnetic Compatibility(EMC)

Part 3-2: Limits-Limits for harmonic current emissions (equipment input

current 16A per phase)

EN 61000-3-3 Electromagnetic Compatibility(EMC)

Part 3-3: Limits-Limitation of voltage changes, voltage fluctuations and flicker

in public low-voltage supply systems, for equipment with rated current 16A

per phase and not subject to conditional connection

EN 55024 Information technology equipment-Immunity characteristics-Limits and

methods of measurement

EN 60950 Safety for information technology equipment including electrical business

equipment

CE marking



This device is in conformity with the following EC/EMC directives:

APLD-I USER MANUAL

TABLE OF CONTENTS

Preface i

Brief Introduction 1

Specifications......................................................................................1

Motherboard Components................................................................3

Header Pin Definition and Jumper Settings.........................................5

I/O Ports...............................................................................................8

Multi-language Quick Installation Guide 9

English...................................................................................................9

Simplified Chinese...............................................................................11

Korean......................................................................................................13

Indonesian.............................................................................................15

Japanese................................................................................................17

Vietnamese..........................................................................................19

APLD-I USER MANUAL

Brief Introduction

Specifications

SoC

• Single channel DDR3L SO-DIMM memory architecture

• 1 x 204-pin DDR3L SO-DIMM socket supports up to 8 GB

• Supports DDR3L 1600 MHz SDRAM

Memory

• 1 x M.2 slot(Socket 3 key M 2242/2260/2280 for SATA SSD)

(It shares the same signal with SATA2)

• Supported by Intel® Apollo Lake 1296 BGA

- 2 x Serial ATA 6Gb/s devices

Expansion

Slots

Storage

Rear Panel I/O

LAN • Realtek RTL8111H Gigabit LAN

• Realtek ALC662-VD0-GR 6CH HD Audio CODEC

• Realtek ALC105VF 4ohm 3w Amplifier (optional)

- 6 Channel High Definition Audio Codec

- Compliant with HD audio specification

Audio

• Onboard Intel® Apollo Lake 1296 BGA

• 1 x 24-pin ATX Power Supply connector*(or DC_IN port at rear

panel)

• 1 x 4-pin SYS_FAN connector

• 2 x USB 2.0 headers support additional four USB 2.0 ports

• 1 x USB 3.0 header supports additional two USB 3.0 ports

• 2 x Serial ATA 6Gb/s connectors(SATA2 shares the same signal

with M.2 slot)

• 1 x Buzzer

• 1 x Front Panel switch/LED header

• 1 x Front Panel audio header

• 1 x Clear CMOS jumper

• 1 x MONO jumper

• 2 x COM headers

• 1 x Case open header

• 1 x SATA power connector

• 1 x Debug card header

• 1 x Printer header

• 1 x Amplifier Speaker header

Internal I/O

Connectors &

Headers

Note: Please go to our website for the latest CPU support list.

Note: Please go to our website for the latest Memory support list.

• 1 x DC_IN port*(or internal ATX_POWER header)

• 1 x PS/2 Keyboard & PS/2 Mouse connectors

• 1 x D-sub (VGA) port*(or DP port)

• 1 x HDMI port

• 2 x USB 3.0 ports

• 1 x RJ45 LAN connector

• 2 x USB 2.0 ports

• 1 x Audio port (1 x line-in, 1 x line-out, 1 x Microphone)

Note: * VGA port(real panel I/O) + DC_IN port(real panel I/O) and DP port

(real panel I/O) + ATX_POWER header(internal I/O header) are alternative

options of the motherboard.

Produktspezifikationen

Marke:	ECS
Kategorie:	Hauptplatine
Modell:	APLD-I
WLAN:	Nein
Breite:	170 mm
Tiefe:	170 mm
Anzahl USB 2.0 Anschlüsse:	2
Eingebauter Ethernet-Anschluss:	Ja
Zertifizierung:	CE/FCC Certification\nErP/EuP Certification\nWHQL Certification
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Anzahl HDMI-Anschlüsse:	1
Audio Kanäle:	- Kanäle
USB 3.2 Gen 1 (3.1 Gen 1) Anzahl der Anschlüsse vom Typ A:	2
Unterstützte Arbeitsspeicher:	DDR3-SDRAM
Anzahl der Speichersteckplätze:	1
Arbeitsspeicher Typ:	SO-DIMM
Unterstützte Arbeitsspeichergeschwindigkeit:	1600 MHz
RAM-Speicher maximal:	8 GB
Unterstützte Speicherlaufwerk-Schnittstellen:	SATA III
Anzahl PS/2 Anschlüsse:	2
Anzahl USB 2.0 Schnittstellen:	2
BIOS-Speichergröße:	64 Mbit
BIOS-Typ:	AMI
Anzahl DisplayPort Anschlüsse:	1