Dux Proflo 125T1 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dux Proflo 125T1 (16 Seiten) in der Kategorie Kessel & Heizkessel. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
H0421 0421 Rev. K
Specications and materials may change without notice.
Effective for all Proo electric storage water heaters manufactured and sold after 1st January 2012.
Owner’s Manual
Electric Storage Water Heaters
Standard Models:
80F118G, 80F124G, 80F136G
125S118, 125S136, 160S124, 160S136
250S136, 315S136, 315S236, 315S248
400S136, 400S236
An ‘H’ at the end of the model number indicates that the
water heater is tted with a hard-water anode.
For advice, repairs and service, call:
1300 365 115 (Australia)
0800 729 389 (New Zealand)
Carefully remove all packaging and
transit protection from the heater before
installation. Dispose of the packaging
responsibly using re-cycling facilities
where they exist.
Installation Details
Owner’s Information
Warranty
Owner’s Manual – Proflo Electric Storage Water Heaters
H0421 0421 Rev. K
Installation Details 1
Plumbing Connections 3
Electrical Connection 5
Specications 6
Operating Instructions 7
Safety Information 8
Service Information 9
Troubleshooting 10
Warranty 12
Contents
Š Dux Manufacturing Limited 2012. All rights reserved.
Owner’s Manual – Proflo Electric Storage Water Heaters
1
H0421 0421 Rev. K
Installation Details
Installation Requirements
This water heater must be installed
by a licensed tradesperson, and in
accordance with:
• AS/NZS 3500.4 Plumbing and
Drainage – Heated Water Services.
• AS/NZS 3000.
• Local authority regulations.
• Outside Australia, please refer to
local plumbing and building codes
and regulations.
• Notice to Victorian customers from
the Victorian Plumbing Industry
Commission – this water heater
must be installed by a licensed
person as required by the Victorian
Building Act (1993). Only a licensed
person will give you a compliance
certicate, showing that the work
complies with all the relevant
Standards. Only a licensed person
will have insurance protecting their
workmanship for 6 years. Make sure
you use a licensed person to install
this water heater and ask for your
Compliance Certicate.
Water Supply Pressure
This water heater is designed for direct
connection to water supply pressures of:
80, 125 and 160 litre models:
- 1,120 kPa
250, 315 and 400 litre models:
- 800 kPa
Where the mains pressure can exceed
or uctuate beyond the pressure
shown above, a pressure limiting
device (complying with AS 1357)
must be tted in the cold water inlet
supply. This device must be installed
after the isolating valve and set below
the pressure shown above. Note that
during periods of lower demand, water
pressure may increase.
Caution: This water heater delivers
hot water at temperatures exceeding
50°C. Refer to AS/NZS 3500 and
local regulations regarding the need
for additional hot water delivery
temperature control.
Pool Heating
This water heater must be used for not
pool heating.


Produktspezifikationen

Marke: Dux
Kategorie: Kessel & Heizkessel
Modell: Proflo 125T1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Dux Proflo 125T1 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Kessel & Heizkessel Dux

Bedienungsanleitung Kessel & Heizkessel

Neueste Bedienungsanleitung fĂźr -Kategorien-