Dürkopp Adler 744 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dürkopp Adler 744 (26 Seiten) in der Kategorie Nähmaschine. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/26
Contents Page
Part 3: Service Instructions 744-122
1. Notes Prior to Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Transport Carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Right End Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Left End Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Marking on the Material Guide Rail and the Material Stopper . . . . . . . . . . . . . . . . . 5
2.4 Transport Carriage Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5 Material Guide Rail Stroke Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Material Stopper Mounting and Material Stopper . . . . . . . . . . . . . . . . . . . . . . 9
4. Distance from the Material Guide Rail to the Needle . . . . . . . . . . . . . . . . . . . . 10
5. Light Barrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Synchronizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. Adjusting the Machine Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1 Folding Over the Machine Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2 Adjustment Disk to the Arm Shaft Crank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3 Position of the Lower Timing Belt Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.4 Rocker Bolt for the Hook Drive and the Left Shaft Bearing . . . . . . . . . . . . . . . . . . . 15
7.5 Hook Drive Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.6 Needle Avoidance Movement of the Hook (Ellipse Width) . . . . . . . . . . . . . . . . . . . 16
7.7 Symmetry of Looper Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.8 Hook in Hook Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.9 Setting the Hook to the Needle Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.10 Needle Rod Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.11 Needle Protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.12 Bobbin Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.13 Needle Thread Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8. Thread Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9. Throw-Over Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9.1 Distance to the sewing unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9.2 Setting the Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9.3 Setting the Height of the Counterholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9.4 Setting the Position of the Placement Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9.5 Setting the Speed of the Smoother Movement . . . . . . . . . . . . . . . . . . . . . . . . . 27
Home
Part 3: Service Instructions
1. Notes prior to adjustment
These servicing instructions describe the
adjustments to the sewing unit in the appropriate
order.
Here it is to be noted that the various adjustment
positions are interdependent. It is therefore
essential that the adjustments be made in the order
described.
Attention Danger of Breakage!
After disassembly and prior to restarting the
sewing unit, the required adjustments must
be made as described in these instructions.
The sewing unit must not be started with the
wrong direction of motor rotation.
Attention Risk of Injury!
Should adjustments have to be made in the
area of the needle and the needle not be
absolutely necessary to these, it should be
removed to avoid injuries.
The main switch should always be turned off.
The only exceptions are those adjustments
which must be made with testing, setting or
sewing programs from the control unit.
Attention!
With some adjustments it is necessary to move the
transport carriage manually.
This is possible with the main switch OFF.
When the main switch is ON, e.g. when the testing
program is to be used, the step motor is under
current and its braking effect stops manual
movement. In this case the fuse 3 for the step
motor must be removed from the control panel.
For all adjustments to parts forming stitches a
faultless needle must be used.
Upon request you will receive the following
adjustment gauges:
Order no. Application
933 80207 Dail gauge
933 80193 Angle for the looper symmetr y setting
933 80194 Indicator for the looper symmetry
setting
933 80200 Feeler gauge for the thread take-up
disk
933 80203 Gauge for the hook drive housing
933 80221 Gauge for the rocker bolt in the hook
drive
An adjustment disk in the machine head has the
notches A,B,C and D. An arresting pin, order no.
211700, for locking into the various adjustment
positions can be found in the package with the unit.
In conjunction with the letters on the handwheel the
arresting pin can be pushed into one of the notches
through a hole.
2.
Transport carriage
Caution in the area of moving machine par ts
- Risk of Injury -
The transport carriage is guided on the extension
pipes at the front by the ball sleeves 2 and at the
back by the track rollers 1.
They have been set tight at the factory. To remove
axial play only loosen the excentrically bearinged
lower rollers 1 and set tight. Check for ease of
movement.
The transport carriage is advanced by the step
motor for the following speeds: Stitch condensing,
Normal stitch length and transport carriage return.
Through a coding on the material stopper it is
possible by primary seams to reduce return speed
for a partial or complete run according to the rail
form. See 5.1.10 of the Microcontrol summar y.
1 2
3
3
2.1_ Right End Position
If the right position has been set with the L<-W->R
key, right diode bright, then the carriage will stop at
the right.
The distance between the middle of the cylinder 4
and the middle of the needle should be 212.5_mm
in the right end position.
Main switch off
- Risk of Injury -
Preliminary Adjustments
– The b417.6 selector switch on the back of the
control unit front panel must be set closed for
1000 mm and open for 1250 mm, appropriate to
the rail length used.
– With the main switch Off, set the transport
carriage with the bracket 6 over the switch b7.
There must be a gap of 0.5 mm between the
bracket 6 and the switch b7.
Also between timing belt clamp 9 and switch b8.
– With lit right diode and a long tap of the
L<-W->R key, set the parameter value to 0 with
the numeric keypad.
– A gap of 105 mm must be set between the cast
guide 8 under the machine arm and the clamp
piece 5.
– In order to avoid a collsion of the transport
carriage with the machine head during a
malfunction of the step motor, the safety
stopper 7 is to be set at a distance of 25 mm
from the machine head at the right.
The distance of the safety stopper 11 at the left
behind the machine head should be 45 mm at
1000 mm sewing length and 58 mm at 1250 mm
sewing length.
– Switch b8 serves as a safety switch. Its
distance from the mounting plate 10 should be
53 mm by 1000 mm sewing length and 55 mm
by 1250 mm sewing length.
All setting measurements can be seen together
in the following dimension sketch.
For the fine adjustment of the right end position
see the next page.
b8 10
11
9
b8
105 mm
25mm
8 7
5 6 b7
212,5 mm
4
4
Produktspezifikationen
| Marke: | Dürkopp Adler |
| Kategorie: | Nähmaschine |
| Modell: | 744 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Dürkopp Adler 744 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nähmaschine Dürkopp Adler
6 Oktober 2024
4 September 2024
4 September 2024
28 August 2024
19 August 2024
16 August 2024
13 August 2024
7 August 2024
7 August 2024
6 August 2024
Bedienungsanleitung Nähmaschine
- Nähmaschine Juki
- Nähmaschine Sinbo
- Nähmaschine Emerio
- Nähmaschine Tristar
- Nähmaschine Medion
- Nähmaschine SilverCrest
- Nähmaschine Bestron
- Nähmaschine Guzzanti
- Nähmaschine AEG
- Nähmaschine Alfa
- Nähmaschine Ambiano
- Nähmaschine Siemens
- Nähmaschine Jata
- Nähmaschine Lervia
- Nähmaschine IKEA
- Nähmaschine Durabase
- Nähmaschine Blaupunkt
- Nähmaschine Hema
- Nähmaschine Home Electric
- Nähmaschine Micromaxx
- Nähmaschine Mio Star
- Nähmaschine Solac
- Nähmaschine Privileg
- Nähmaschine Livoo
- Nähmaschine Easy Home
- Nähmaschine Prixton
- Nähmaschine Lifetec
- Nähmaschine Singer
- Nähmaschine Husqvarna
- Nähmaschine Termozeta
- Nähmaschine Crofton
- Nähmaschine Brother
- Nähmaschine Kohler
- Nähmaschine Primera
- Nähmaschine Veritas
- Nähmaschine Toyota
- Nähmaschine Janome
- Nähmaschine Victoria
- Nähmaschine Kayser
- Nähmaschine Jocca
- Nähmaschine Aigger
- Nähmaschine EasyMaxx
- Nähmaschine Bernina
- Nähmaschine Elna
- Nähmaschine Necchi
- Nähmaschine Pfaff
- Nähmaschine W6
- Nähmaschine E&R
- Nähmaschine Carina
- Nähmaschine Empisal
- Nähmaschine ER
- Nähmaschine Feiyue
- Nähmaschine Gritzner
- Nähmaschine Hofmann
- Nähmaschine Huskystar
- Nähmaschine Husqvarna-Viking
- Nähmaschine Kenmore
- Nähmaschine Lewenstein
- Nähmaschine Mediashop
- Nähmaschine Muller
- Nähmaschine Novamatic
- Nähmaschine Siemssen
- Nähmaschine Silver
- Nähmaschine Sinojo
- Nähmaschine Tesco
- Nähmaschine Vendomatic
- Nähmaschine Weasy
- Nähmaschine Yamata
- Nähmaschine Zippy
- Nähmaschine Union Special
- Nähmaschine Kunft
- Nähmaschine Meister Craft
- Nähmaschine RCE
- Nähmaschine Yamato
- Nähmaschine Baby Lock
- Nähmaschine Łucznik
- Nähmaschine Anker-Bernette
- Nähmaschine LERAN
- Nähmaschine Prince
- Nähmaschine Bernette
- Nähmaschine Sewmaq
- Nähmaschine SteamMax
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024