Dual XPA2100 Bedienungsanleitung

Dual Empfänger XPA2100

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dual XPA2100 (12 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

INSTALLATION/OWNER S MANUAL’

Mobile Power Amplifiers

XPA SERIES

XPA2100

XPA4100

XPA6100

XPA SERIES INSTALLATION

Preparation

Please read entire manual before installation. Due to the technical nature of amplifiers,

it is highly recommended that your DUAL amplifier is installed by a professional installer

or an authorized dealer.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the amplifier where it would be subject to high temperatures, such as

from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• All amplifier installations require power, signal and speaker wires (not included).

• An amplifier installation kit (sold separately) is highly recommended to facilitate the

installation. Consult your dealer for recommendations.

Mounting Location

• Choose a mounting location for the amplifier. Suggested locations include under a seat

or in the trunk.

• The amplifier can be mounted horizontal (recommended) or vertical. For optimum

performance, make sure to provide at least 1" of space to around all sides. Do not

mount the amplifier under carpets or where airflow is restricted.

• Do not install the amplifier where it may be exposed to moisture.

• The optimum mounting location varies between vehicles. Remember to test all

amplifier functions before completing the final mounting procedure.

TYPICAL MOUNTING METHOD

NOTE

Be sure to follow specific instructions included with your amplifier installation kit

(not included with this amplifier). The information below should be used a general

guideline only.

Power Wire (+12V)

• Disconnect negative battery terminal before proceeding. Consult a qualified

technician for instructions if you are unsure.

• Plan wire routing before cutting any wires to length. Begin by routing the power

+12V wire from the battery to the amplifier location. Use a grommet when running

wires through the firewall or metal openings. Avoid running the power wire near

existing vehicle wiring to prevent induced noise from entering the audio system.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s

electrical system.

Ground Wire (GND)

• The amplifier ground wire should be as short as possible. Choose a clean unpainted

section of metal or the vehicle chassis when attaching the ground connection. Be

sure to clean the area of any dirt or grease.

Remote Turn-on Wire (REM)

• The remote turn-on wire connects to the head unit's amplifier turn-on lead or

power antenna output.

Speaker Wires

• Choose adequate gauge speaker wire depending on your exact amplifier/speaker

combination. Be sure to observe polarity when connecting.

• Do not ground any speaker wires or connect any speaker wires together.

Input Signal

• The amplifier's input signal connects to the head unit's low level (RCA) or high level

(speaker wire) outputs.

• Low level input signal deliver the best performance. If unavailable, use the high

level inputs - when interfacing with factory head unit for instance.

CAUTION

• Do not use both low and high level inputs at the same time - connect only one or

the other.

• Never run any wires underneath or outside the vehicle.

XPA SERIES INSTALLATION

Connection Descriptions

Produktspezifikationen

Marke:	Dual
Kategorie:	Empfänger
Modell:	XPA2100
Breite:	226 mm
Tiefe:	233 mm
Produktfarbe:	Rot
Übertragungstechnik:	Kabelgebunden
Höhe:	54 mm
Zweck:	Auto
Material:	Aluminium
Eingebautes Display:	Nein
Betriebsanleitung:	Ja
Gehäusematerial:	Aluminium
LED-Anzeigen:	Ja
Audio Kanäle:	2.0 Kanäle
THD, totalklirren:	1 %
Rauschverhältnis (SNR):	75 dB
Frequenzbereich:	20 - 20000 Hz
Akkus/Batterien enthalten:	Nein
Übergangsfrequenzen:	50 Hz
RMS Leistungsoutput pro Kanal (2 Ohm):	75 W
RMS Leistungsoutput pro Kanal (4 Ohm):	50 W
Bass-Boost:	0 - 12 dB
Maximum Eingabeniveau:	6 V
Eingang Empfindlichkeit:	200 mV
Lautsprecher-Konnektivitätstyp:	RCA
Leistungshöhepunkt pro Kanal:	300 W
Eingebautes Crossover:	Ja
Output Widerstand:	8 Ohm